Ford 6.0L Power Stroke Diesel :: ABS Light Goes On / Flashing TowHaul With CEL?
Oct 20, 2016
Okay I have a 2007 F350 crew cab powerstroke dually that is totally stock and motor has 32k/cab has 130k. She normally runs perfect, I've replace the unison ring in the turbo, one fuel injector was replace, the EBP sensor was, cleaned the EBP tube was cleaned, EGR stuff is newish, new altenator and upper motor was cleaned of all the carbon. All of that was done in last 6 months and I use Rotella T6 with OEM filter. So this morning I start her up just fine and go to get coffee, when I'm leaving my ABS light goes on. I pull over to shut her off then restart and ABS light goes away.
I drive for 15 minutes go inside this office for 10-15 minutes then get back in my truck and leave. While I'M driving I hear this slight tingling every so often, like something is touching the brake dust shield on my L/F wheel. I fill her up with diesel then leave gas station to have my TowHaul light start flashing with a lit engine light. I scan with my scan gauge 2 and get P000, I've read the P000 means there are no diagnostic trouble codes. All the temps were within spec, she was still running gd, shifting gd and braking gd. The flashing towhaul light is a transmission issue rt, so if that's flashing there should have been a DTC besides the P000. Then the ABS light going on earlier is not a coincidence ...
View 6 Replies
Advertisement
I have an 03 excursions with 6.0. I downloaded the sct livewire ts and the problem started. Through truck has no power the thief light flashes codes for cam and crank sensor and on when it acts up the glow plug light comes on. On the on the ts monitor it says no key in the ignition.
View 11 Replies
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
View 10 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
View 12 Replies
My co-worker has an 06 F250 SC 4x4 and is getting a P0713 code. 2006 Ford F250 6.0L Diesel ... Tow/haul light comes on flashing at random times. Truck is reading a P0713 code which is the TFT Sensor Failure/Replacement
Ford dealership is telling me that I also have to pull the valve body and install the new upgraded wiring harness (3-3.5 hours labor) but a thread on this forum stated I just needed to replace the sensor in the tranny pan and reconnect the wire harness. Do I need to upgrade the wiring harness?
View 3 Replies
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 Replies
So driving the other day and tow haul starts flashing. I come to a stop sign and goto take off and it barley takes off. It will barley roll if my foot is off the pedal sometimes wont even roll. Also won't shift into 6th. Once it gets rolling though say till about 25 it's fine. Just doesn't wanna take off? I scanned the trans but got no codes. And here are some pressures and stuff but I don't know what I'm looking for with the trans. This was all done in park.
View 14 Replies
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 Replies
6.7 with 19k . Drove about 2 miles and noticed dash lights were flashing and ac was not working correctly . Pulled into garage shut off and truck wouldn't restart, no crank ! All my dash lights were flashing & dash was giving numerous messages.. At least I wasn't on my road trip 2 weeks ago! 3400 mile round trip. Truck was towed to dealer! My 6.0 never left me stranded & I had 3 of them..
View 14 Replies
Came on other day. No ses light or fault codes. What it means?
View 10 Replies
The heated seat button led flashes with no heat on seat pads. I'm guessing this means there's an open in the circuit somewhere?
View 4 Replies
Okay so I just peaked 100k and (of course) my 6.0 has an issue. I was driving along when suddenly my Transmission Temp gauge dropped to nothing, the tow haul began flashing and my check engine light came on. My transmission hard shifted and wouldn't shift up from 3rd. I let the truck sit for a few days, no leaking was observed and no blown lines. I added 4qts of tranny fluid and went to take it for a spin. The truck did fine for about 20 minutes and the same issue occurred. I parked it and checked the dip stick and it was full. What could the issue be.
View 5 Replies
The overdrive light is flashing but not all the time. What does this mean?
View 3 Replies
My F350, 7.3 L. is flashing the overdrive light. Had a pro do a scan that said no Turbine speed sensor signal.
I would like to know where the TSS is located and then see if it has corrosion other reason not to connect.
View 10 Replies
I am trying to make sense of a P0741 code accompanied by a flashing OD light.
The truck is a 2002 (12/01) build date) F250, 7.3,4x4, Auto, with 245,000 miles on it. The truck seems to shift fine but around 40/45 it feels like the TC does not lock, followed by the flashing OD light.
The transmission was serviced 500 miles ago but the OD light flash was intermittent until last week, now its been constant. I want to take care of it before I do any damage.
View 1 Replies
I have a persistent issue with the OD off light flashing on my 2001 7.3L auto 4x4. Scanning it with AE I get the P1832 code. The truck runs and drives just fine. It shifts nice, goes into overdrive, locks up, etc. If it weren't for that blinking light I'd think it was all perfect. I've checked all the connections, replaced the range switch / neutral safety switch, replaced the VSS on the rear axle, checked all light bulbs and fuses. I've checked MOST of the relays in the truck.
I pulled the tranny drain plug and poured out a bit of fluid into a clean pan, it looks and smells good. AE also tells me that it's not communicating with the ABS system (although there's no persistent ABS warning light on the dash), the Airbag, the Overhead Trip Computer, the Parking Aid (which I don't have...), or the Enhanced Powertrain. The temperature on my overhead display is reading -40F which is clearly wrong.
I've looked for a comprehensive wiring diagram for the truck, but can't find one. I'm trying to figure out if there's a connector or module that these various functions go thru that might be the problem. Am I missing a ground somewhere? The frame was just powdercoated......am I not getting a good ground connection? In complete disclosure, I have torn this truck apart and re-assembled it out of several different trucks as outlined in this thread.
[URL]....
View 8 Replies
I have a 02 f250 4x4 7.3l.... I drove it all weekend and no problems. It sat till yesterday I got in it to go to church. It started up and had a little miss was around 60 f. Then the od light started flashing. Not in any code just constant flash. I was parked down in my drive way. It idled fine but acted like it wouldn't take fuel. So looked around and found the hose on the map sensor was broke.
So today I fixed the hose. Checked the oil level and battery connections. Still running weird and flashing od light. I got under the hood and wiggled plugs I unplugged the ice. It revved up then back down and started running smoothly. Got in it and it backed out of the drive way. It ran and drove fine. What I need to know is why??? The ice is a new one from Ford.
View 11 Replies
I test drove my truck yesterday for the first time with the newly rebuilt transmission. I was gentle with the right foot and all seemed well. Once out on the main road it shifted by itself into overdrive for the first time and immediately the O/D light started flashing. I drove it home and shut her off. I test drove it 2 more times leaving overdrive off, no issues. With a snap-on scanner hooked up I let it go into overdrive and O/D light started flashing again, not immediately maybe 5 seconds after shifting into O/D.
Codes are:
p1316 IDM codes detected
P0717 Turbine speed sensor circuit fault
P0715 Turbine speed sensor circuit fault
P0500 VSS fault
10 minutes ago was my last test, O/D flashes only after it has shifted into overdrive. I checked the transmission wire harness and all connections are tight, trans oil level is good & trans temp never went above 150. Could this be a faulty VSS?
View 14 Replies
I have an early 1999 Ford F350 4x4 7.3. I purchased it used about a year ago. The trans was replaced with an ATS 4R100 and a billet torque converter. I have the paperwork for it to confirm it along with the mileage when it was installed. It currently has about 35k on the new trans.
Several months ago the trans heated up to about 200 degrees on my trans temp gauge that was already installed when I purchased it. Not a huge deal and after pulled over and high idling it off I went and no problems.
About a month ago I was towing my fifth wheel when I noticed the temp rising on a level grade. I also noticed the OD light flashing. I made it home and when I went to drive it the next day light was not flashing and it shifted and drove like normal without the trailer.
I towed the trailer again and same thing, OD light flashing and started heating up. I changed all the fluid and flushed it based on the trans flush procedure I got in this forum and replaced with an OEM trans filter. Towed the next day and everything was good. Temp was good and no OD light flashing but I lost 4th gear. All other gears shifted fine, no slipping, just won't go into 4th.
On my way back home the OD light started flashing again and instantly the heat started rising on the trans again. I was finally able to get it into 4th if I let off a little, but as soon as the OD light started flashing I lost it again.
I have a friend of a friend who works for Ford who offered to come over to hook his scanner up. When he hooked it up there was no stored codes from the OD light which we both thought was odd. Took it for a test drive and the OD light started flashing so we could get some readings. He said it showed an error shifting from 1 to 2 and another error when shifting from 3 to 4. I unfortunately forgot to ask him for the specific codes. He tried to read the torque converter info but said my truck was to old and the PID was not supported to read that info.
He said it appeared it was mechanical but without some type of break out box where he can physically shift the gears he couldn't say for sure if it was mechanical or electrical. He did not seem to interested in doing that test for me as he rebuilds trans on the side and said he could rebuild it for me.
It seems my overheating takes place when the OD light starts flashing. It still drives fine and shifts smooth with no issues with or without the OD light flashing. 4th gear usually doesn't work but on a rare occasion it will go into 4th fine which makes me believe it may be electrical.
I am new to diesels but have learned a lot about my 7.3 lately. I recently installed injectors, up pipes, hutch mod, and several other little things so I can get things done myself but am just a DIY'er who can follow good directions. I know very little to nothing about transmissions though.
While working on another issue I did notice there is a large wiring harness that connects up on the driver side of the trans. I unplugged it and was checking the wires and after removing the dirt and crud on it you could see the outside wire sheathing had deteriorated exposing the copper. I bought some liquid electrical tape and sealed everything up. I did look for a replacement wire harness at the time and the one I ordered was very similar but the plug was different so that is why I used the liquid tape at the time. I did not seem to have a problem at the time after fixing it but wanted to mention it here in case that may be an issue.
I also thought swapping out the solenoid pack may fix it. I did not want to drop the trans and send it for a rebuild if I did not need to. I know there are some other sensors associated with the trans like the TSS I think but don't know if they are even related to my issue.
I tried getting the codes from the guy but he does not have them and I can't get him back out. I have an OBDlink device connected to Torque on my phone but I couldn't get it to read trans codes. Could be user error.
View 10 Replies
Saturday morning my grandpa drove my F350 into town pulling our 4-horse trailer (With living quarters). I wasn't with him, but I was told the following: he started smelling something hot and noticed the O/D light start flashing. Now, this man is not the most intelligent man on the planet and uses the O/D to "slow down the engine" when he starts and stops - i.e. uses it as trailer breaks. I have asked repeatedly for him to quit, but as best as I can tell, he continues to do so.
After the burning smell, a driver pulled up next to him and pointed down - he looked to see smoke and the truck puking fluid everywhere. He said he thought the truck lost power because he couldn't get it to move. Ended up getting it towed. The tow truck driver checked my fluid level and said I had an extremely small amount of transmission fluid left in the truck...which made sense as the fluid was all on the ground underneath, lol. Fluid was NOT red and looked really gross and there was DEFINITE burnt smell to it.
My question is this - what in the world could have caused the truck to do this (I read that is could be from overheating?), and what should be my next course of action? It is home and in my backyard right now (Classy!). It starts and runs fine, but since there is little to no fluid left, you have to hammer down on it to get it to go anywhere. It does move, however.
View 14 Replies
