Ford 6.0L Power Stroke Diesel :: A/C Is Not Blowing Cold - Refrigerant Leak
May 18, 2016
So, trucks A/C is not blowing cold, and i replaced the compressor a couple years ago ( 40k miles?) took the truck to a shop to have them use one of them sniffers to check for a refrigerant leak. Was told that it needs a new evaporator core. Charged the truck up with refrigerant and it blew cold for a while but is now blowing hot again and it's summer time here in FL
So, replacing evaporator core here? I tried to find some how-to videos on youtube, but to no avail. I'd like to do it myself if possible. I think the shop quoted 3-400 in labor atleast.
View 8 Replies
Advertisement
I have noticed a refrigerant oil smell coming out of the A/C vents when I first start my truck with the a/c on.. smells like the PAG oil in the A/C system.. I got under the truck and stuck my finger in the condensate drain and it's oily, and has the same smell.. the A/C is still blowing cold, but the smell is getting worse..
View 10 Replies
Ac is no longer blowing cold air and was thinking about trying a can of ac pro on her. However, I have heard some pretty bad stories about people killing their compressors and overcharging the system. Is it not worth the risk.
View 7 Replies
Just as the title says the ac on my truck is not blowing cold like it used to, it has enough air flow but it's just not cold?
View 5 Replies
Blows cold, so not a freon issue, but it will sometimes just suddenly stop blowing cold as if I punched the "A/C" button disengaging the compressor. Sometimes if I just wait a while it will come back on by itself, sometimes I have to stop and shut the truck clear off and take the key out, then start it back up and all is well again and it blows cold again.
High pressure switch failing???
BCM issue???
View 6 Replies
So my Ac is not blowing cold at all. I can hear the compressor cycling. I filled the sys with freon. Still not cold I am pretty sure I have a leak but wouldn't it still blow cold? What do I need to check to fix this? The temps are getting in the upper 90's and 100 s I need Ac bad...
View 14 Replies
I have a 07 6.0 powerstroke, I had 2 bad injectors so I replaced all of them with reman's. I had a problem with them coming loose. the first time this happened it hydrolocked the motor, number 8 cylinder. so I pulled all the injectors and replaced all the seals and washers and torqued them down a little more than spec like 27 lbs. it runs great and starts great even at 25 degrees but I noticed this morning that when starting it up after it sits (cold) it blows blueish smoke until late it warms up and I accelerate. is this normal? should I check fuel filters? oil in fuel?
View 14 Replies
My 02 F350 7.3 new to me trucks ac stopped blowing cold. Not air gap issue (shims have been removed prior to my ownership-I pulled hub and checked), the charge is good (according to the shop I went to for evac and refill), and the compressor's cycling quickly. I'm no HVAC guy by any stretch. I have a cheapie gauge from days long ago that I connected to my low side port (which I know isn't definitive) and it reads from 25 to about 40/45 depending on the cycle.
Additional info that may not be anything:
1) Where the line goes from accumulator to evaporator the foam seal is slightly messed up and I feel ice cold air coming out of the housing.
2) The line is warm before the orifice and cold after it.
3) The lines going to the accumulator are both hot (after taking it to shop, before were lukewarm).
4) The condenser doesn't seem to have excessive plugging and I have rinsed it with garden hose sprayer with no difference.
5) The air from the vents blows good, just warm.
6) I've replaced the actuator for the blend door already.
View 14 Replies
99 f-350 crew cab. The A/C is not blowing cold as it should. Have already replaced the compressor and clutch, orifice tube and accumulator, also cleaned evaporator coil and put a new blower motor on, also a new blend door actuator. Also put a valve in to block coolant from the heater core. System has had vacuum pulled and charged correctly by my mechanic, he says he doesn't know of anything else to do, that it was as good as its going to get. Ive been in 2 more trucks identical to mine and the A/C will freeze you out, as to where mine will not come close. Temp coming out of the vents barely gets down to 60 degrees
View 14 Replies
I purchased 2011 F250 King Ranch Edition about 3 months ago. I'm loving the truck and not had any issues until 3 weeks ago. I locked the truck as usual using the key Fob, and upon returning to the truck, I noticed the doors weren't locked. After some brief trouble shooting, I discovered the the fuse was blown that according to the manual controls just the power door locks. I thought it was strange that a new truck would be popping a fuse so I replaced it...a couple of days later it blew again. This time I was locking the truck with the door key pad. I took it to the dealership and they checked it over and said they replaced the fuse and cycled it numerous times but could not reproduce the problem. The told me that they even put a call in to the Ford engineers and they said check the key pad for water intrusion. The dealership told me they disassembled the key pad and found nothing wrong....lock and unlocked the door some more and the fuse would not blow. I picked the truck up four days ago and the fuse blew again last night. Everything else works...alarm sets and goes off if any of the doors are opened. The only thing that I can find that doesn't work when the fuse is blown is the remote start.
View 14 Replies
Well it's that time of year to start using my air conditioning. Went to use it today and it is blowing nothing but warm air. Worked perfectly last time I used it last year. I thought about buying that 134a ac recharge kit from auto zone.
View 14 Replies
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
View 4 Replies
It only happens on a very Rare occasion.
When Cold, and when I start out as I open the throttle, it suddenly sounds like there is not a piece of quieting stuff on the engine. I mean its like I can hear right into the engine itself.
I back off, It goes away then I dont hear it again for another Month or two.
View 14 Replies
I picked up a 2003 6.0 awhile back went ahead and did studs,gaskets, delete. Was driving it and seemed to lose power, started coughing and carrying on blowing bluish white smoke then shut off. Ended up hydrlocking #5, Oring on injector was tore when took out. Put all back together, ran horrible, did a balance test with AE, showed #3 injector, replaced, ran horrible, did AE dropped #1 injector. So in process of replacing the rest of the injectors. Just wondering why it is or was dropping them 1 at a time. Ficm was showing 47.6 to 48.6 volts, could that be it?????
View 14 Replies
I just recently repaired issues with my 6.0 and now new issues has begun. The turbo keeps blowing the pipes out of the rubber hoses. Not sure what is happening or why so a little insight would be useful.
Oh yeah out of all the work completed in my previous post..don't bother replacing the solenoid section of the injectors. I replaced two the bad ones, rebuilt the other 6 with new everything including a cleaning and now I am getting codes for 3 that are going bad. Oh well I tried right...
View 14 Replies
Replaced the vacuum solenoid.. Thought that would fix the ac blowing threw the defrost when I switch to 4x4, but didn't fix the issue, 4x4 works great. There is another little diaphragm that has a vacuum line to it that opens and closes, could this be causing the air to go defrost? I'm going to go to a buddies house and test for leaks this Saturday, just trying to get a jump on it...
View 1 Replies
Have 06 super duty . Heater air blowing only on defrost. 4wheel drive. Is this a vacuum problem or some type of sensor or control problem?
View 2 Replies
6.0. 115,000 miles. Everything stock, except bully dog intake filter.
I replaced the FICM recently, with one that I bought from the guy who makes those cool You Tube videos, Diesel Tech Ron. I also replaced the EGR valve. I also replaced the intercooler boots on the hot side. I cleaned the intercooler pipes. I cleaned the intake filter as well. I'm still blowing out black smoke, if I floor it when I need to pass someone.
Follow up question: I bought those boots from Riff Raff Diesel and I bought new clamps, too. I'm not sure if I installed correctly. It's already blown one off (it blew the top of the intercooler pipe off, by the turbo, but the boot stays on the turbo) and I put it back on and tightened it all the way down, and I've had to re-adjust 2 times, now, since it acts like it still wants to slip off. Do I simply have the other ones misaligned???
View 14 Replies
I have a 2006 F350 6.0 litre diesel. The other day I started it up drove away and it was blowing huge plumes of white smoke out of the exhaust. Shut it off.....started it up again after a while then went on a long drive and it went away. What that was?
View 6 Replies
I have a 2006 6.0l f350 crew cab that blows air hard every time I accelerate. Sounds like you're going 100mph with the hood unlatched. It blows real hard for a minute and goes away if I accelerate through it or let off.
View 7 Replies
