I just got a 5 inch turbo back Magnaflow stainless exhaust system installed on my 2007 F 450. The downpipe rests directly on the firewall and causes a horrible vibration and noise at times. I have been on the phone talking directly with Magnaflow trying to resolve this issue
View 6 RepliesOver the weekend I replaced the passenger side up pipe with one that doesn't have a spot for the EGR cooler. After putting the turbo back in it has a pretty bad exhaust leak. Sounds like it is on the drivers side somewhere near the Y pipe. When replacing the passenger up pipe I didn't loosen any manifold bolts or anything and I am thinking that the Y pipe is out of alignment with the turbo. What is the proper procedure to loosen everything up and get it aligned on the turbo? My guess is remove turbo, loosen drivers side manifold, loosen passenger side manifold, loosen passenger up pipe and tighten it again now that everything isn't under tension, install turbo and clamp to Y pipe, tighten manifolds. Is that the right idea?
View 8 RepliesI just bought a 2007 F350 CCSB 6.0 auto 4x4 with 113k miles on it, it does have the 5th wheel goose neck trailer hitch in the bed...anyway of course when I looked at the rig everything checked out and now I am getting a U1900 for ABS CAN communication...I should add that the ABS Light itself is not on, just the CEL...I have a feeling it has something to do with the wiring that the PO maybe had done to wire for his 5th wheel hitch?...I checked all the ABS related fuses in both fuse boxes and they're all fine...
While reading another post on the possibility of the brake pedal position switch up on the pedal itself being bad, someone mentioned that the wiring may be jacked up due someone adding wiring in for the 5th wheel hitch...I also checked the brake pressure switch on the nose of the master cylinder and that looked clean although I didn't test it...should I just replace these since they're pretty cheap or is there something I should look for in the wiring underneath the dash? Oh and of course my cruise control isn't working either...likely because of this ABS wiring issue..
I try to turn on my truck today and it will not crank. The day before I had change two injectors and I turned on the truck when two fill up my tank and I put a full bottle of injector cleaner with it. When I drove off, a few blocks down the truck turn off on me. I started to turn on the truck and every time I did it would blow heavy white smoke out the tail pipe and then it would shut off. I did this about 10 times until I decide to call a tow truck. The next day I empty out the fuel tank and fill it with diesel only. I tried to turn on the truck and it would not crank. I ended putting two new batteries and still the same result. What can this be ? 2007 6.0 Diesel ...
View 14 Replies2007 F-350 6.0L, Wife phoned and said that the truck backfired a couple of times and there was black smoke from exhaust. When she stopped at idle there is now alot of white smoke but coolant level looks fine. She has about 200 km's to go before she is home pulling a 20 foot horse trailer with 1 horse.
View 14 RepliesI have 07 F350 6.0 never heard this out of any of my 6.0s. it's almost a whine but can hear it w turbo and out of empty exhaust. Almost like a supercharger noise stumped almost leaning towards actuator for turbo? Noise got real loud swapped turbos used same actuator noise is there but much quieter.
View 1 RepliesI have a 2000 Ford F350 7.3 with the auto and 262,000 miles on it. As far as I know everything is stock on this truck. It has been a great truck but lately its been making a strange noise. It almost sounds like an exhaust rattle or vibration but it is intermittent. Its not really loud it can be heard best in the cab at idle. I've looked all over on the truck and haven't found anything. I can't pinpoint where it is coming from. I tried starting the truck with the serpentine belt off no change.
I took the inspection plate off the bell housing and couldn't see any cracks the torque converter bolts appear tight, and the starter is not engaged while running. I've read a few forums on the torque converter going bad. It looks to me like its more the 99 trucks that had trouble with that. Did the torque converter issue carry over to the 2000's? Would a torque converter/transmission problem be intermittent?
I have a 2011 that does not currently have the complete factory exhaust system on it and no muffler. With the nice weather I have been driving around with the windows down and hear a noise out of the exhaust that sounds like tires spinning on wet pavement when I let off the throttle or at some shifts of the transmission. Boost seems normal, and don't hear any noise while under load. I think it is just the VGT closing and making the noise. With deleted sys heard this noise in exhaust?
View 4 RepliesI had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
Truck is an '07 F350 Supercrew, 8ft bed, SRW, 2wd. I bought the truck last month and noticed a low frequency driveline vibration starting at about 45 mph and is noticeable to about 65 mph. Feels like a bad u-joint. So I pulled the drive shaft (two piece) and checked the joints. They seemed find so I sent it to a commercial truck shop that does driveshaft work. Had the joints replaced and the shaft rebalanced.
Re-installed drive shaft and went for a test drive. No real change in the vibration. The hangar bearing seemed fine so it wasn't changed. Doesn't feel like a wheel out of balance. My experience tells me its a drive shaft.
I have a code for #6 low contribution and a thumping noise out the exhaust. When I turn number 6 injector off the popping/ thumping goes away. Truck is straight piped and deleted. It started doing this after getting on it hard to get on the high way. Sounds like beating an empty pop bottle on something
View 14 RepliesI just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
On my way home from picking up or new Voltage 5er, I could hear a loud squealing noise when we pulled up to the house. After crawling around the under side of the truck I found the last exhaust thermal couple had either blew out or just fell out.
View 9 RepliesBlown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
I ran about 500 miles today loaded up pretty good and noticed every bump I hit that was enough to rock the truck and trailer that there was a noise I've never heard before. It was like the difference between asphalt and concrete road surfaces, but was only present when the springs were sufficiently compressed. Temps were between -10 when I left to 10 or so above when I was destinated. Would that cause the noise?
View 3 RepliesI have a 2007 Ford F-250 6.0L that's making a vibration noise when I come to a stoplight with my foot on the brake, just idling. I just recently replaced the front brake pads this past weekend. I looked under the hood and visually checked for any obvious things that could be making the noise and did not find any, I did notice my power steering pump is damp with fluid. Now this noise only occurs when my foot is on the brake, anytime my foot is off the brake, it goes away.
I checked brake fluid level and power steering pump fluid level, both are fine except power steering fluid looks like chocolate milk. I don't know if the power steering pump would be the cause of this, but I'm going to replace it because it's leaking and I'm guessing the fluid for the power steering is way overdue. I've only owned this truck since March of this year and it has 128,000 miles on it. Hopefully this video link to youtube works, the sound in the video is the same noise that I'm hearing from the truck. Where this noise is coming from.
Vibration noise powerstroke - YouTube....
For a while now, I have been hearing a very high pitch whistle noise from the turbo/exhaust area. Everybody told me it was an exhaust leak, but I never could pin point the leak. While I was under the truck last weekend I found the flex joint on the passenger side up pipe was broken a leaking.
I ordered a Dorman replacement pipe that comes with a new gasket and hardware.
I will be the first to admit, I am not a fan of Dorman parts... BUT, this pipe is really nice. It looks identical to the pipe being sold on Dieselsite.com, it doesn't have the scoop inside to direct exhaust gas to the EGR cooler and it comes with all the mounting hardware.
[URL] ....
Once I got the turbo down pipe out of the way and soaked the bolts with penetrating oil, I had the broken up pipe off in 30 minutes.
So at low idle my fan is running like 230rpm according to torque pro. I think this is causimg my ect to rise when at idle. It's usually 192-194* but if I'm idling in traffic or just In general (after it's been running a while) it climbs to 195.8, 197, 199.2, 201, 203, 204.8. Haven't seen it get higher than the 204. Now once I get moving again it will lower back down. I can see where I have flow into the degas not to mention the water pump is new. Could my low fan speed be my issue? I believe it should be more around 500rpm at low idle.
View 14 Replies I have a 4 inch MBRP turbo back straight pipe and I hear a lot of other 6.0 that sound much louder.
just curious as to why that may be?
Would there be much oil in the down pipe if the oil deal was leaking on the turbo? I broke it loose to look at it and not much there, one small area that looked like it has had on it..
View 13 RepliesPrevious owner of my truck installed a front leveling kit (2" aluminum shims under the coil spring seats) and was told by a dealer that it definitely lead to the wear and tear on the front end, specifically the track bar and track bar ball joints. They also stated it causing the truck to still pull to the left even when aligned because the geometry was off. My truck has 56k miles on it.
I was informed of this after months of trying to correct the death wobble. After 4 alignments at NTB, I took it to the dealer for diagnoses. I paid them to do the labor of replacing the track bar, but elected to remove the leveling spacers myself. Came out in about 45 mins, but had to purchase the shorter stock seat bolt from the dealer which was only available as a package with the coil spring seat...
Truck now rides better and seems perfectly aligned, before it pulled hard to the left. Wish I would have known about this earlier...