2007 350 the truck sat overnight (15 hrs) I went to start the truck and it had to crank for about 3 seconds which is abnormal for my truck?? It was about 80 degrees outside. Is there any reason for that?
View 7 RepliesI am lost on what I need to do with my 2005 6.0. Last summer it started giving me trouble once in a while starting. I turn the key on and wait for the wait to start light to go out. When it goes out, turn the key and it starts, most of the time. Last summer I went to start it the same way, only it cranked and did not start. I turned the key off, back on and cycled the wait to start light again and turned to the start position, it started right up. Whenever it would act up I just turn the key off then back on and it starts right up. Usually on the second try, but lately it has taken 3 or more tries. I am not finding any real pattern to when it wont start.
When it does not start I can crank on the starter until the battery dies and it wont even think about starting. Turn the key off and back on, it will start.
Another thing I have noticed, when I crank the engine I can hear a clicking from under the hood right before it starts. I think it must have something to do with the injectors. I will crank the engine a few seconds, hear the clicking then it starts. If I don't hear the clicking it will not start, so when it doesn't want to start I also do not hear the clicking sound.
The other day I started it, drove 5 or 6 blocks and shut it off. After 20 minutes or so went to leave. I had to cycle the key 4 or 5 times off and back on before it decided to start. It is getting worse, doing it more frequently, and taking several times of key off and back on to get it going. Where should I start looking to find this problem?
Truck is an '07 F350 Supercrew, 8ft bed, SRW, 2wd. I bought the truck last month and noticed a low frequency driveline vibration starting at about 45 mph and is noticeable to about 65 mph. Feels like a bad u-joint. So I pulled the drive shaft (two piece) and checked the joints. They seemed find so I sent it to a commercial truck shop that does driveshaft work. Had the joints replaced and the shaft rebalanced.
Re-installed drive shaft and went for a test drive. No real change in the vibration. The hangar bearing seemed fine so it wasn't changed. Doesn't feel like a wheel out of balance. My experience tells me its a drive shaft.
I just bought a 2007 F350 6.0 two days ago, so I was giving the truck a good wash today using a electric pressure washer. The engine bay was pretty dirty so I decided to take some soap and a brush to it. After cleaning it I let it sit for a while in the sun to dry. (engine was stone cold). After it had completely dried out I go in and it cranked right up. I let it idle for a good minute-minute and a half put it in drive and pulled away slowly, right when I touched the accelerator it started running rough, so I popped it into neutral and let it idle for a sec but it was still running really rough so I cut it off not wanting to damage anything worse.
I let it sit and tried to start it again, it just turned over and over. I checked the oil level it was good. So I pushed it back into my driveway to figure it out. I took ICP connector out and tried to start it, just turned over and over. took fuel filter out it was just replaced 2K miles ago it looked a little dirty but not super bad. I put that back in. took icp out again and tried to start it and it started but ran super rough and was dumping black smoke out.
I checked back all ficm connectors and they were all connected. I haven't checked the voltage on that yet, but plan to do that tomorrow. the previous owner had the ficm go bag about a year ago and he sent it off to ficmrepair.com and they fixed it for him. also he had the stand pipes and dumby plugs done as well as the stc on hpop. im kinda at a loss on where to go now other than to check voltage on ficm.
First off I'm new to the 6.0 powerstroke that being said, I bought a 07 f350 with 102k miles in VERY good condition and I'm planning on doing the bullet proof on it. But my question is that when I start the truck it will turn over about 5 seconds before it starts up. I've even cycled the glow plugs twice with no difference. If I shut it off after it's warm and start it right back up it'll still turn over for about 3 seconds.
View 14 RepliesI have an 04 ford 6.0. It is an 03 model. It has 165xxx miles. It fires right up cold but, once warmed up it will crank but not even try to start. A little starting fluid and it will fire right up. I sent the FICM in and had it tested and it is good. I put in new 850CCA batteries and a 185 amp alternator so my voltage is good. I changed the fuel filter and the oil/oil filter, synthetic 5w-30. It isn't throwing any codes. I am really hoping it's not the HPOP but, think it's probably that or related to it.
View 14 RepliesAbout a month ago my truck was cutting out at one point it wouldn't even crank, got it going took it to the shop found my driver side battery clamp cracked, replaced it aswell as the egr valve because I had a p0401 code. Valve was pretty gummed up. Now recently it started doing it again. It cut out and it started right back up then later that night drove it two blocks and died, turn the key on and my glow plug light stayed on and wouldn't crank, was checking over all my connections and nothing seemed to be wrong. And then randomly it seemed like everything reset and my injectors would buzz, glow plugs cycled and fuel pump kicked on and started right up and drove home.
I replaced the pcm relay because one terminal looked to have gotten hot. Let her warm up in the driveway and she cut out twice but started right up. Checked over the connections again, replaced and cleaned both batteries, took it for a drive and no problems, later on started up again and let her warm up and cut out again, this time I got the p0401 code again. (Egr insufficient flow). I'm at a loss not sure where to keep going. It's an 04 f350 with egr delete, banks turbo and intake, with edge juice with attitude tuner on level 3 never switched levels around. And some other add on and mods that could make the list go on.
03' F350 Crew Cab DRW FX4 Lariat 6.0
180k miles
Has EGR Delete
Blue Spring Kit and recent Fuel Filter Kit
Last Friday I got the truck back from a local mechanic that had replaced the water pump. Took it out to put fuel in it last night. About a mile from the house it felt like it bucked then died. While still rolling I stuck it in Neutral and started it back up. Got fuel and back home, no problem. Total trip around 4 miles.
This morning I get about a mile from home (other direction) and it does the same, engine quits and it rolls to a stop. Except now it won't crank. Has electric power, just won't turn over. Both batteries are pretty new Napa big CCA ( I believe 800 ).
I walk back home and get my '04 F250 6.0 (180k also) and drive back to the stricken 350. Thinking a battery may have crashed a cell I remove the ground from one battery and jump it off with the 250. No difference. Reconnected battery #1 and Disconnected battery #2 ... Same thing, no crank.
I didn't really think it was a battery issue since it started fine, but if one of them had crashed a cell it could have shorted. No dice.
Now I'm thinking it may be the fuel pump. Would not having line pressure keep it from at least cranking? IE like a safety feature so the injectors don't try and run dry?
I have a 2004 f350 6.0 powerstroke i recently fixed a oil leak in my remote oil cooler and after I was finished it ran fine and ran fine for a few days I noticed yesterday it had a bit of a rough start and some today but would start and run normal. Started the truck this morning and drove it a bit and then let it sit while I went to the dentist came back out and truck wouldn't start. I am getting 200-330 icp with the ipr cycle at 88.5 ficm sync is good and colts are at 12.5 unplugged icp sensor to see if it would start after that and it disnt start so I ruled that out.
I'm currently waiting on AAA to bring my truck home for me but trying to make sure I'm right to start working on it tomorrow. I am thinking the ipr valve is clogged. Am I right to think this may be the issue? When I first installed my remote oil cooler I had the same issue crank no start turned out to be the ipr valve was gunked up and I ended up replacing it 300 dollars later. Then it started and everything was fine. So basically am I right to start at the ipr valve or should I start somewhere else?
2003 6.0 will fire within 2 seconds when cold, literally a "bump the key" and she fires up scenario. Recently and only when the engine is hot I'm getting extended crank times and sometimes it takes several attempts for the truck to start. I replaced the HPOP with an upgraded pump after the factory HPOP went out at 311,000 miles. I know this sounds like a standpipe leak scenario but it doesn't act up all the time, sometimes it fires right up even when its hot. my thinking is a leak is a leak and only gets worse.
My IPR is reading in the 26% range, FICM is steady in the 47.5 to 48 volt range and at idle 585 to 600 psi on the ICP with a good FICM sync. I'm going to to use my scan gauge and see if I can catch an extended crank scenario to see if the ICP is reaching 500 psi but is there somewhere else I should be looking? FICM relays possibly? I've noticed when i turn the key on I'll hear the fuel pump,vacuum pump but the clicking sound is very brief or nonexistent (not sure what the clicking noise is from I assumed glow plugs but its absence is noticed)...
I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.
View 8 RepliesSo my recently purchased 2005 f350 has an abnormal long crank. I searched all the internet and everything pointed to STC fitting. Well I knew I had some other things I wanted to knock out so I ended up buying an update kit from sinister diesel. It included an updated fitting, new degas cap, updared turbo oil feed and return lines, blue spring update, and "dummy" tubes or something like that.
During the last few days I have removed the turbo, and finally got to the hpop. As I was removing the turbo I thought I might have the updated lines as there was no braided area in the feed tube. Sure enough I pulled the hpop and I have the one piece fitting. So now that I have wasted all this time removing all this stuff for no reason I still don't know what is causing my long crank. I am going to probably install the new fitting and lines anyway but where do I go from here?
I have a 2003 Ford F-350 super duty 6.0. A few weeks ago it starting loosing power, it wouldn't even go up to 15 mph. It now won't even move. There is 0 power. When I press the gas the motor bogs down to a very low idle and wants to die. I also had recent trouble with it starting. It would wind up to a very very low idle and about a minute later it would crank up to full idle. I changed the fuel filters (on top of the engine and under the cab) and also changed the fuel pump under the cab. After that I still have no power when pressing the gas it will still act like it wants to die.
View 14 RepliesI have a PS 6.0 in my '04F350 that starts very reliably but stalls within 1-2 seconds. Restarts after cranking for 5-30 seconds. This only occurs if the truck sits for more than 6 hours. The longer the truck sits, the longer it has to crank to restart. Also if the tank is full and the truck is parked pointing down hill this does not occur, if it is parked pointing up hill it occurs even with a full tank. Shows no codes. I've had several mechanics look at it and no one has been able to explain or propose a solution expect for wholesale replacement of parts. The symptoms indicate to me that air is getting into the fuel system but I'm not sure where to look.
View 10 RepliesI think my starter took a s hit like I said truck randomly doesn't crank all lights on dash come on can hear injectors buzzing turn key nothing. Took wire off passenger's side of truck yellow wire touched to pos post solenoid click no crank. So I had the old lady sit in the drivers seat well I hit the starter with my BMFH started right up could something else cause this or should I just bite the bullet and replace the starter?
View 7 RepliesMy nephew has a 2004 F350 that will crank but will not start. It will build oil pressure on the gauge. There is no injector buzz and no communication through OBD2 port. Is the PCM dead?
View 10 RepliesI went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 RepliesI have a 2006 F350 with around 208k mikes, automatic with a no start, 0 No FICM Sync.
The CMP and CKP has "no / 0" for synchronization and a "NO" synchronization from the FICM. Should this be "yes / 1" when trying to start?
The camshaft position sensor status indicated "yes fault".
FICM is at 48V,
DTC currently on
P2614 camshaft position signal output/open circuit - CMP
Glow plug circuit cylinder 2, 4, 5, 6 (these have been on for 12months and 1,000 miles and never had an issue starting)
B1352 - left front temperature damper motor
B1360 - left rear temperature damper motor
U1900 - CAN - communication BUS fault
I am running all OEM filters
The other day, I started having problems with the truck not starting when at operating temp. Went for a drive and stopped a a scenic overlook, and spent about 30 minutes taking pictures. Went back to the truck, and it wouldn't start. Outside temp was about 95 degrees.
I tried for about half an hour to start it, but all it would do is turn over. There was a work crew there with their heavy machinery, and I was able to borrow their starting fluid. One quick squirt into the intake, and it fired right up.
Although I do have an oil leak from the right valve cover, when I checked the oil, it was just off the full mark. The truck was parked on a slight angle with the driver side being about a foot higher than the passenger side.
2003 F350 w/6.0, 180,000 miles
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 RepliesI have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 Replies