I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 RepliesTruck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 RepliesI'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesI have been debating if i should use seafoam engine treatment. My truck has been having issues with the first cold start of the day. I've noticed the rough idle that accompanies the cold start. I live in Denver so this truck sees alot of stop n go traffic. Will seafoam do anything about the dirty fuel injectors. They have to be replaced here soon but will adding seafoam solution buy me more time. If so, what are the steps on how to add. The can isn't very detailed on instructions and Internet isn't being useful. I have an 04 F250 Lariat Power Stroke 6.0L diesel
View 14 RepliesI have an 05 f250 6.0. We have started to reach 38 at night here in northern IL already. The trucks been having a rough time starting and it's not even that cold yet. Any recommendations on the truck that I can do to have easier starts. Sometimes cycling the glow plugs 4 5 6 7 times isn't enough to get her going. I plug it in most of the time on bitter days in the winter but sometimes I leave it parked where I cannot plug it in. The batteries seem just fine. I think one is a little weaker so I will get new batts.
View 6 RepliesI have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 RepliesI have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 RepliesMy '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesI just bought a used 2007 f250 with the 6.0 power stroke. The truck has approx. 160,000 miles on it. He is having a issue with the truck overheating when it is cold out. When the air temp is above 30 degrees or so, he doesn't have a issue. So,my he overheating only occurs when driving down the highway in low temperatures. It can idle in the cold fine.
View 8 RepliesI have 2007 6.0, rough idle starts, rough and no power till engine reaches running temperature, runs great after that. If the engine is off for half hour, and restarted, runs rough again till engine temp is back again.
View 3 RepliesI have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
This is tough one to search on. Most of the results talk about a poor idle or the high idle mod. I simply have no cold idle up. It used to work a few years ago but doesn't anymore. I live in Colorado and it's definitely cold enough for the high idle to kick in. I have no codes, nothing bad shows up on the Auto Enginuity.
View 14 RepliesI'm having a bit of a cold start issue, need to know if it is normal or something is wrong. I live in southern Indiana and it's gotten down to a VERY cold 50 degrees (lol) and the past two mornings I have started it up and it seems to have a misfire first thing in the morning and it will kick into high-idle mode and after I shut it off and start it back up about 20 seconds later after the ECT gets above 100* and it runs perfectly. It has brand new 190/100 injectors from Warren, an IDP tune, and I am running 13 quarts of FoMoCo 15w-40 oil with 2 quarts of hot shot stiction eliminator (tried it before installing new injectors). And also throwing no codes. Is this normal or should I be looking for a problem?
View 13 RepliesMy truck was running rough when cold, I went to check the ficm voltage while wife was cranking and coolant shot right into the ficm and cooked the sumbitch. Stop laughing that stuff happens to me all the time. Anyhow, got a new ficm and truck wont start. Starter kicks out after a few revs. I ran my own solenoid wire to the starter and it cranks just fine. ficm at 48.5 koeo and cranking, icp 1100+, ipr from 14.8 to around 40%, ...
It takes a few seconds for the cam/crank to sync but it does. I changed the fuel filters and primed it, Got new batteries, and threw a crank sensor for s+g. With the key on and me cranking it using the solenoid wire, it almost starts. But from the key it will kick out after a few seconds. All fuses and relays are good. I hear the pcm also controls the starter, could that have cooked when the ficm went or would it blow a fuse? Diagnosing using a scangauge2 ....
My IPR value on torque pro koeo is at 14.7. Is that normal? Usually idles around 23.7-24 but when I experience a slight rough idle IPR will be 26-27. When I was under the truck last week I did see there's been oil leaking somewhere seems leaving evidence on the drivers side rear of bellhousing. Any relation?
View 14 RepliesMy 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 RepliesHave a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesI recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...