2007 6.0 my dash lights will flicker when the key is turned on and the truck wil crank but won't start, but when the lights stop flickering truck starts .. How to fix the flickering dash light?
View 2 Replies2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 RepliesWent out to start my truck this morning and it wouldn't start. Cranks fine and almost started once but died. Checked all fuses all my voltages are good. Oil and coolant are good. When I turn the key on I can hear the fuel pump and sounds like it's priming correctly. Might be an issue with a clogged fuel filter? Maybe? Haven't had any problems or issues otherwise.
View 6 RepliesLike usual, i have a problem that no one else has and it sounds like its something electrical/sensor/PCM related.
Every few mornings, ill go out to my truck and go to fire it up...and it'll just crank away. After i give up on cranking and shut the key off, go to try again, it fires up instantly, like nothing is wrong. Sometimes in the morning itll just have an extended crank but eventually start. Regardless...it always starts. Sometimes it cranks really strong the entire time, sometimes the crank gets weaker the longer you crank...i don't think its HPO related, but i definitely could be wrong.
Ficm voltage looks good KOEO, cranking and running. I had my batteries tested at ford a few weeks ago and they "said" they were good (motorcraft 850ccas). Alternator is strong. When cranking, ive seen the voltage drop anywhere from 10.2 to 9.4v. I never know when this is going to happen and i can't hook up AE every morning and sit and wait, but based on my scangauge, i see ICP shoot up to over 1500 as soon as it fires.
Only code I've gotten is P0148, which is fuel delivery error/engine speed higher than expected. I've gone ahead and replaced my camshaft position sensor with a ford sensor a few days ago...it hasn't done a no-start yet, but it did do an extended crank. I think my next stop is PCM replacement...
New alternator, fairly new batteries....after sitting 5 days or more, it cranks but no start.....put on charger for four hours, it fires right up...
Voltage on the multimeter shows 12.45 on both batteries......could there be something drawing down the amps? If so how do I find it?
My truck usually starts up great, but every so often it takes 3 to 4 long cranks before it will start. By long cranks I mean more than 4 or 5 seconds of turnover. Seems to be no real rhyme or reason to this. It does it engine cold or hot. I have iPhone engine monitor app and numbers seem fine. BTW it's a 2005.
View 12 RepliesI got a 2003 6.0 powerstroke cranks but wont start once it gets hot let it sit for a couple of hours and it fires right up already replaced high pressure pump no leaks visible and when running its great will run till run till fuel runs out. what to check?
View 3 RepliesLately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .
View 7 RepliesCouple weeks ago fuel tank started coming apart clogged all filters. Replaced tank filters and fuel pump and blew out all of lines. Started and ran fine. Stays plugged in over night but now it'll crank but wont start. No codes showing up or anything...
View 1 RepliesI drove the truck Sunday to 3 different places, parked it around 3:00 pm. Went to take it to work the next morning and it just cranked with no start. I pulled the codes as I have an edge insight. I got a P2614 code so I figured it was the cam sensor. We after some reading to what everyone had to say I checked to see if I had RPM when I got home and I did so that put me back to having no clue. I took as many readings as I could to see if any one might see something that I am not.
ICP psi 1280 cranking 23 key on
IPR 41% cranking 14 key on
IPW ms 0.00 cranking and key on
Fuel Pressure 63.1 cranking
ICP voltage 1.6 cranking .3 key on
Mass Air flow 8.3-10.7 cranking 0.00 key on
Engine RPM 166-205 cranking
FICM 47.0-47.5
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesI have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 RepliesI have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesI have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 RepliesI'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 RepliesI have looked through every post and idea possible with no remedy for my no start condition. I have tried everything that I am capable of doing without diagnostic computers and other specialized tools. A little history of what happened. While idling in the parking lot for a few minutes, truck all of the sudden start running rough, and acts like it is going to quit. Hurried out of the parking lot to make sure that I made it home, but the the truck would only get up to about 25 MPH, but I finally made it home(about 3-4 miles).
NOW, the truck won't start at all, but just cranks. Some more detail about how it cranks. It cranks fast, I separated the batteries by disconnecting the grounds on each, and made sure both are charged. Batteries are only 3 months old from Ford Dealership. As the engine cranks, oil pressure registers after a little while, (longer the first time for some reason), and as soon as oil pressure shows up on the dash indicator, black smoke starts coming out of the exhaust. The engine is trying to start a little bit, but it mostly just cranks.
Things that I've done: Changed fuel filters, Motorcraft (new orings). At first the pump was pumping large bubbles through the line up into the upper fuel filter, but after sitting it appears that it is not pumping bubbles anymore, and I cycled the Key more than 10 times. Did the bubble test while upper filter was removed. Unplugged ICP sensor. Pulled EGR, installed new one. Pulled oil filter and made sure that oil is pumping.
Checked FICM voltage, with key on Injectors buzzing, also engine cranking for quite a while. Never dropped below 48.5 V. Pulled FICM just incase and performed repair procedure, still same volts and no start. Coolant level is good. Checked oil level. unplugged EGR. Checked filter Minder. checked for chafing on FICM harness. Unplugged MAF. Checked FICM relay operation, Fuses all around. I need this truck to run.
jump in my warm truck head out anywhere and go inside after shuting the truck off. come back 15 min later and ya she wont start. crank all day long don't make any difference. wait till the oil temp comes down to 60 deg celcius and boom she starts like nothing is wrong. from everything I have read and that's a lot since this has been going on for 2-3 weeks, seems possible to start with the stc fitting. seems to have only become an issue since I did an engine oil flush and oil change. the truck was new to me in early august. truck has 310000 km. the oil change was done mid oct. my issue started once the temps started dropping to -0 deg cel over night. I don't cold start now that its -10 or colder always plugged in for 3-4 hours before heading to work.
View 11 Replies07 6L gave me a fit the other morning. I spent the night in the mountains Saturday night. Sunday morning was -5. With no place to plug in the block heater. When I started it it bucked and hawed and didn't want to run... It keep surging for a while and finally smoothed out after about 3 mins... Is there an additive that will work for this for the times there is no place to plug in? Oil additive or fuel additive?
View 14 Replies07 f250 I just replaced the power steering pump. I put the serpentine belt back on and when I started my truck I now have a squeaking noise. It's driving me nuts and the more I push the pedal it gets alil louder. Now before I did the ps pump I did hear a little noise like of bearings squeaking when I put my ear to grill.... I put the old ps pump pulley on the new pump but I don't think that is it because it is pressed on. Would it be a bad idler/tension pully? Is it just a coincidence after I do ps pump that it now decides to squeak?
View 10 RepliesI have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 Repliesi have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 Replies