Ford 6.0L Power Stroke Diesel :: 2006 - Replacing Batteries Repeatedly - Parasitic Draw?
Mar 13, 2014
I have a 2006 F250. Past two winters my batteries have died. Last yr., bought 2 new batteries and a new alternator. This winter, battries have been replaced twice. I only drive the truck maybe once a week, about 5 miles total. I live in Indiana and we have had many sub zero temps this yr. Its been in the shop all week, the mechanic states that they are finding an extremely small draw but cannot find where it is coming from. The mechanic is wondering if I am driving it enough. Any thoughts on this? Also my batteries came from auto zone, the mechanics thought it was bad that I had bought them from auto zone.....not sure if that should even be a factor....
View 14 Replies
Advertisement
With the hood open and the hood light bulb pulled out, measured the parasitic draw on their truck? I checked mine because it appears my battery is slowly discharging if the truck sits 3 or 4 days. I got 0.24 amps which seems in line with running the clock memory and the computer. I have a feeling the battery is shot even though it is only 3 years old. When I bought the truck it had a ton of yellow fuzz on the terminals. That is cleaned up and with it running I get about 14.35 volts at idle so it is charging. 0.24 draw??
View 10 Replies
About how long do batteries hold up in this truck? I ask because in my 06 6.0 it was an annual event 2 batteries and an alternator.
View 14 Replies
2003 6.0 has had hpop replaced with adrenaline hpop, updated hpop cover, new oem oil cooler and gaskets, holder premium 175/30 injectors, new lpop and front cover, new cam and crank sensors, all new pigtails, rebuilt turbo with 360 bearing and kc billet wheel, egr delete, coolant filter. New ICP and IPR, oem filters and cap. All work done by reputable shop. Truck will run fine and then just die like you turned off the ignition. Everytime IPR is stuck open. Replace IPR and truck will run fine for a short period and then problem will reoccur.
View 9 Replies
My batteries go dead over night, had them checked but they say there good, can't figure out what's causing them to die.
View 8 Replies
My 2014 350 DRW has a battery problem......If it sets for a couple hours, it won't start. With a jump from a very small battery box, it starts right up. I charged it last week for 4 hours and still when in OKC it would need to be jumped at each restart. Do I have one of the batteries going bad.....
View 6 Replies
I didn't drive my truck for one day and the batteries are died. This is the second time this has happen. That is a pretty fast drain time. THe truck only has 2500 miles on it. And I;m talking the batteries a dead dead. I hate having to take the truck to the shop. Just a big inconvenience. And it only happens about three weeks apart. I bet that would be pretty had to find the problem.
View 5 Replies
If I'm giving a jump:
Assume I hook positive and negative cables to the respective terminals of one of the two batteries. The alternative would be hooking positive cable to one battery and negative cable to the other battery, or does that make 24 volts? I'm also assuming if it is just the one battery, it does not matter which one you jump from?
If I'm receiving a jump:
I assume positive cable to positive post of one battery and negative cable to a good ground under the hood somewhere? Again, does it matter which battery I use? I wonder where a good ground is on this crowded diesel engine and aluminum body. Front radiator supports?
View 14 Replies
In the last 2 months I've replaced my starter and 2 new batteries. I've tested the alternator and it's fine. What more is there? I'm guessing the FICM is going to crap. If I attach a scangauge 2 to it now would it tell me if that's the problem?
View 14 Replies
I have a 2000 watt inverter and I want to connect it to my 2011 F250 Super Duty. Which battery do I connect it too. This will only be used every once in awhile.
View 12 Replies
Is there a way to check to see battery health with Dashboss? I know I can check charging system, but is there a way to monitor if the batteries themselves are going south on me?
View 5 Replies
I have both a hydraulic dump trailer with two 12v batteries and an RV trailer with two 6v batteries to supply 12v. Both trailer's batteries are wired to be charged from the tow vehicle if the TV is equipped with a charge line.
Does the OEM 7 pin connector on a 2005 Ford 6.0 F250 CC 4X4 have a charging line on it? If so which terminal / pin is it?
What gauge of wire is it and how much amperage will it deliver to the connector? For testing, when is it hot? When the truck is running only? When the key is on? Is it hot all of the time?
View 11 Replies
I ve been noticing that the alternator isn't charging correctly, or at least it seems like it. We drive short trips sometimes two times a day, a mile or less. One day, night actually, I noticed it started to not turn over with it's usual enthusiastic sound. When the batteries get discharged to a certain point, the voltage at idle will be less than 12 volts. If I rev the engine for a bit, the volts jump up, but at idle it drops back to 12 or below. Seems to me that it should be at least 12v or above if the batteries are discharged, and more towards 12.5ishV if the batteries are fully charged.
After I put it on a 6A charger overnight, the voltage upon starting is above 12, sometimes over 13. But if the batteries start to dwindle down from short trips, the voltage drops to 12 or below at idle.
I did install the smaller pulley a few years back, and that worked massively. I couldn't get 12V at idle before installing the smaller pulley. But now it seems like I'm back to that same situation before installing the smaller pulley.
So, I m guessing that a alternator bench test is in my future? The batteries are fairly new, tho they have been down to nothing at least twice from boneheaded moves by yours truely!
And, I'm speculating that this charging situation contributed to the recent FICM replacement that I went thru.
View 14 Replies
I just bought the batteries I was asking about in this posting. Bought them at auto zone on my lunch hour today, they swapped them out right there in the lot, no problems. Watched carefully to make sure terminals were not crossed, etc. When I came out of work a few hours later, the #20 fuse for door locks was blown. I chalked it up to the battery change, and put a new fuse back when I got home. I come out an hour later to leave, and the fuse is blown again. I have not replaced it again, need to go get more of the proper amp rating.
No other changes to the truck other than the battery replacement. And that's the only anomaly. No other problems, nothing. Getting ready to head cross-country on a skiing trip, this Friday, so there really is no time to get to the dealer to get this looked at.
View 6 Replies
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 Replies
I replaced hv battery and starter tried one time to engage and then nothing. i replaced 12v and still nothing. switch powers on and when pushed again simply powers down.
View 9 Replies
This is my first dual-bat vehicle. 2011 F250 with ~60K. Dual alternators. Bought in August of 2010. One battery(passenger side) was leaking pretty badly in ~2012 and was replaced under warranty along with the harness as it was corroded.
Yesterday, I drove the truck quite a bit on ~20-25 mile trips and left idling during a couple of them while inside Home Depot. No indication of any trouble.
Today, would not remote start, and when I put the key in and turned it to the on position, the dash lit up for about 3 seconds but once it started waking everything up, it all went dead. Start results in a faint click. I got 11.2V from a trusted meter. I've got my 20A charger hooked to one side right now.
Is there any special trick or attachment procedure to charge a dual battery setup? What about jumping off? Does one bad battery cause both to "act" bad? If I can determine which battery is causing the issue, am I safe to replace just that one, or should I get two new batteries?
View 14 Replies
The truck is a 2004 f250. Build date is 7/ 03 so its an early 04. I have been in a parking lot for 3 days now with no money trying to get this truck to start. Me and my dad replaced the ipr pigtail and the ipr thinking this might have been the problem, because the ipr pigtail had a damaged connector.
Before doing this work the icp sensor connector had no oil in it, now after replacing the ipr and cranking the engine the icp has some oil in the connector, could this cause a short and not let the truck start, and if so will unplugging the icp allow the truck to start?
We were having trouble with no starts before this happened and when it did all we had to was push the ground wire back further that goes back to the ficm and the truck would start, but that is not working anymore.
Is it possible the ipr is not seated properly or the new ipr is bad out of the box? Or maybe the made in tawain pigtail connector to the ipr is bad?
We are thinking it may be a short somewhere in the harness since everytime we pushed the ground to the ficm up further to where it grounds before when we had no start problems this might have took the short out of the ipr or icp pigtails and allowing the truck to start. Injectors are buzzing when key is turned and I can hear the fuel pump.
View 14 Replies
Can you replace the passenger side up pipe without pulling the turbo, etc? My bellows blew out. Y-pipe is still ok. I've already deleted the EGR, so what's the best to put back? Go back to the original style or just put in a straight pipe? Where to get one?
View 2 Replies
Ran fine, did the head gaskets ,egr delete, oil cooler and 12mm dummy plugs. Primed the fuel system, oil pressure looks good on the guage , spins fine but doesn't seem to be making any attempt at starting . Gave it a shot of quick start and it never so much as kicked. Everything looks good, nothing leaking and nothing obvious. To top it off we are without power after Hurricane Mathew left his mark.
View 14 Replies
What is the correct way to clock the transfer case so it will line up with the new transfer case shift motor. I have read that you should not clock the transfer case shift motor.
View 8 Replies
