Ford 6.0L Power Stroke Diesel :: 2006 - No Start While Hot
Aug 18, 2017
I just bought another 2006 model to take some of the strain off my first one with 435,000 miles. This one is a completely stock 250 with 171,000 miles and the previous owner said it would not start when it got hot.
So I started with the air test, had a leak in one of the stand pipes. Fixed it and still a no start while hot.
Pulled turbo and checked if the stc had been replaced. It hadn't so I replaced it. Air pressured checked, all good. But still no start when hot.
The thing that baffles me is if you run it till it gets hot, shut it off and try to restart it will restart each time you try until you let it sit for 2 or 3 minutes and then it will not build over 250 icp psi.
The only code I'm getting is a b1318.
View 1 Replies
Advertisement
Background: My 06 started up and ran fine until #7 injector took a crap.I had the injectors replaced with 155/stocks from warren.
Well no we're having an issue with a hot no start. Starts and runs just fine cold but once up to temp and you shut her down you can't start it again till it cools. Air tested it 3 different times can't find any leaks. Swapped out the ipr with a new one my mechanic had just to see and no change, unplugged it and no change.
What it could be. When warm and trying to start it only gets 300psi. The only other thing i can think of is hpop, but to go just like that without any trouble before hand has me puzzled.
View 11 Replies
I've been having an intermittent problem with a no start condition when hot. It has lately gotten worse to the point that I was dead in the water for about 25 minutes while i had the hood open to allow things to cool off. I closed everything back up hit the key and it jumped to life just like it was new. I've read through the tech folder as well as several other threads regarding no starts but haven't run across anything that is pointing me in any one direction. It cranks over very strong on new interstate batts that are only 6 months old and the SGII shows sync on the FICM and I'm getting a good RPM signal showing about 160-170 cranking RPM.
Good logic power and showing 47.5 to the injectors. I'm running an atlas 40 from Ed in the FICM. I've wiggled wires and done a cursory look but I would think that if there was any chaffing that cooling off wouldn't affect it and it would be dead until fixed. Once it is running I have no problems, never let me down or quit on me while under way. Again, it is intermittent where I'll have 3 weeks or a month of no problem at all and then run into long crank times for another couple of weeks.
I've made no mods to any of the HP oil system and have no leaks that I can see, no consumption between oil changes. I'm in the middle of building a house right now and need the truck to be reliable. I'm pretty good with a wrench if I know what the problem is but I don't know where to start on this. It's an '06 model but an '05 build date on the motor.
View 1 Replies
My 2006 F-250 6.0PSD has a new hitch. Tonight it would not start once hot. It cranked and cranked but no start. My scanner showed ICP readings of 366PSI during cranking. Far below the 500PSI needed before the computer will fire the injectors.
So is this the STC fitting at the HPOP that is failing? If so how long will she start cold and drive normal before she leaves me stranded? I have the fittings and new dummy plugs and stand pipes as well. I was waiting to to do this work until I had the money for an new EGR cooler and oil cooler.
I know my oil cooler is failing as my deltas are showing a 15-19 degree spread over my coolant temps.
View 14 Replies
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 Replies
This truck is bone stock FYI. I get in it to crank it and I get nothing. Batteries are good, everything in the cluster lights up, and looks normal. No codes are thrown. I can hear the solenoids click under the dash and hood. I check the voltage of ignition cable at the starter and I get no reading.
There is a single thick yellow with light blue stripe coloured wire on the passenger side of the engine compartment, beside the vacuum pump with a "squeeze and pull" type disconnect. Disconnect it, and connect the male half of the connector to the passenger side battery positive terminal. Do this with the ignition key in the RUN position. Does the truck start?
This is where it gets weird. The truck does start and after i reconnect the wire it it starts normal. I started it several times throughout the day. The next morning I get in the truck. No start. I have to use the wire and manually connect it to the battery and it starts right up again. This time I get a "Tow/Haul" light blinking on the dash. It will go into gear but pressing the acceleration pedal does nothing. I turn it back off, attempt to start it normally and it starts right up. No it will go into gear and drive. Now I am thinking maybe the neutral safety switch?
Could it be a solenoid sticking or the neutral safety switch or something else entirely?
View 14 Replies
I have a 2006 Ford F-250 6.0 powerstroke with 100,000 miles and it puts out a puff of smoke at cold start up every time and also when I run it then park it for maybe 1 1 1/2 and it puts out a puff and also I noticed when I get to work with is about a 20 minute drive I get there around 8 then leave at 5 I noticed it puts out a puff then if I watch the exhaust I can see a slight haze but I figured it's just condensation.
Here's the list of stuff I have put on the truck... Oringed heads by librator performance, with oem gaskets every thing, arps head studs, egr delete, airdog 2 fuel system,mtw stage 2 turbo, bulletproof ficm,coolant filter, banks intake, fuel pressure set at 68 and fuel regulator return.
Here's a list off parts I put on trying to fix the smoke I put in 5 injectors because the ford ids had a slight change and after that it was straight line I put in hpop and turbo drain pipe and I tested the ficm and its 48 with the key on and cranking and running...
View 14 Replies
06 6.0 f250, I went out of town for 2 weeks came back home and went to jump in my truck and it seemed like it almost started but didn't then slowly each time I tried it seemed like the battery was draining down. Is this just from it sitting for so long without cranking or is it something else my scangauge says I'm getting 11.5 volts. Do I need to just jump it off or get a whole new battery. Or is it another issue?
View 2 Replies
Just replaced injector 4, oil cooler and did egr delete. Ficm is at 48 and truck will not kick over. New batteries installed.
View 14 Replies
176,000 miles. Replaced heads and oil cooler approx 25,000 miles ago. Haven't had a lick of engine problems until today. Just got my '06 out of the shop getting new brakes and rear wheel bearings today. Drove to the store to grab something for dinner and it wouldn't start.
Checked my scangauge and only getting 350lbs HPO.
View 14 Replies
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
View 11 Replies
So my 06 6.0 4x4 is just about to break 200,000km and I've done most of the upgrades and work myself. (All the updates are in my Sig). My problem is that when I'm cruising and the engine is at full operating temp, if Im bellow 80-100km/h nothing but as soon as I break into that speed range about 2000rpm the truck will start to shudder. Almost feels like its not firing properly is the best way to describe it. Why this could be happening or causing it?
View 7 Replies
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 Replies
I have a 2006 Ford F-250 with the 6.0 with 99,000 that puts a puff of white with a tint of grey that smells like unburnt diesel smoke at start ups it will do it cold ever time and will do it when i let it sit for maybe a hour but not every time. I've noticed I had higher egts then before also not sure if it's related at all or not. I had on the ids the graph was a straight line for the injectors, pressure checked the coolant cold and hot doesn't loose pressure. No puking, New hpop. Here's what I have done to it, oringed heads,arp studs,remote oil cooler, factory injectors,egr delete,air dog 2 fuel system, coolant filtration, bulletproof ficm, regulated fuel return, stage 2 mtw turbo,CCV mod, banks air intake. I'm stumped!
View 14 Replies
My wife and I went on vacation for our anniversary and the truck ran fine for a while then we went back to get ready and when we left it started up and everything seemed fine but it died about 200 yards later and is now cranking but not starting. Left my toolbox at the house (stupid!) And truck is new to me so I don't have gauge or reader. Checked the fuel filter under the hood and fuel pump is pumping. Any other tips on what to do that could be the problem without buying parts?
View 14 Replies
I have a 2006 f250 with a 6.0 and I am having some issues with a hesitation and lose of power. The hesitation is worse when under load and other times is not so bad. Also it is non existent at higher RPMs (2500 and up). I changed the egr valve 2 months ago and it seemed to fix the issue (95%) but now it is running bad again. I used Hot Shot oil additive 2,500 miles ago and I changed the fuel filters and changed to 5w 40 Rotella synthetic oil, nothing has changed. I had the FICM changed a year ago with new software updates, still didn't fix it 100%.
Now I am having a "hard" start issue. It takes a bit for the truck to turn over. My batteries are 12 months old and I just replaced the alternator so I am not sure how to proceed.
I did just buy a Scangauge II and I am still figuring out how to use it. It says there is no codes.
View 2 Replies
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 Replies
I recently purchased a 2006 f350 with 6.0 power stroke. I drove it approx 15 miles shut the truck off, let it sit for approx 3 he's. Then I drove another 15 miles and shut it off. When I went back to it. To start it up would not start. The dealer said brand new injectors when I bought the truck. I tried to start it for approx ten min. I didn't want to bog down the battery. So when it wouldn't start I sprayed a shot of starting fluid and it took right off. But when you shut it off it won't start again.
View 14 Replies
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 Replies
I have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 Replies
Ok the icp .hpop.ipop.crank ps and ficm is all good but still no start. I've sprayed alittle starting fluid and still don't start idk what else to do this truck is driving me up the wall it's been down for 2 weeks.
View 5 Replies
