Ford 6.0L Power Stroke Diesel :: 2006 - No Start When Died After Shudder - Code P2291?
Apr 23, 2017
I have a 06 6.0 no start . I was at a light felt a slight shudder went to take off felt another shudder and it just died. Changed fuel filters, unplugged icp no start still. No code at first now throwing p2291. Fuel pressure is at 62 when cranking. Hooked up air to the icp port and only heard air coming out of both valve covers inlets. Ipr was at I believe 60 to 65% when cranking. Little back round 2 years ago I did the whole sinister diesel top end kit and put the updated parts in. New o rings on everything that took them, new egr valve, standpipes and dummy plugs. On the injectors all new o rings and crush washers. I believe that's everything.
View 11 Replies
Advertisement
I was working out here on a site north of OKC and the truck has been running great all day. I shut it off to do the job and 20 mins later it will not start. I pulled the codes P2291 low ICP. One thing I noticed is that I cant hear the lift pump running when I turn the key on. I even drained the bowl on it and still can't hear anything. So I'm thinking bad lift pump or something.
View 14 Replies
Which is, Injector Control Pressure Too Low. First filter change on this truck. Purged the truck six times. No start. Purged it six more times. The truck started momentary. I've been purging for the last two hours. Now I have the code. What next?
View 14 Replies
As the title says I am suddenly having a long crank when starting and low oil pressure when when warm (above approximately 100 degrees). IPR goes to 85% when cranking. Stored codes were P2290 and P2291. Other symptoms are low power and what sounds like a power steering pump with low oil whine and low power. (It is not power steering related however, I checked.) I pulled the oil filter and cranked engine and filter bowl filled in less than 10 seconds.
Oil did have a fair bit of air bubbles. Oil has 5000 miles and is Motorcraft 10w30 diesel. I have not added any since the last change. I do not have the new style pump so it's not the STC fitting. What my issue is? I do have AE if any other info is required. Particulars are in sig. The searches I have done combined with the mileage I have lead me to either the low pressure pump is failing, or the high pressure pump has lost the ball bearing out of the side.
View 6 Replies
I have a 2011 F450 with a 6.7. It has 99K. The whole fuel system was replaced about 10K miles back. I installed a dieselsite aux fuel filter/water separator after that. Has been running like a top till this am on the way to work. Right before I get to my biz the reduced power warning came on, fortunately I made it into the parking lot at my biz. Then the engine died and it would not restart. Hooked it up to auto ingenuity and I got the P0087 code. I changed the diesel site fuel filters and the stock primary and secondary fuel filters.
The diesel site had a little bit of sediment but no water whatsoever. The Ford filters were very clean and had no trace of sediment or water, but I replaced them anyways. I cleared the code and tried to restart the engine but it will not start. Checked for codes again and now has P0087, P2291 and P2539. The pump is kind of loud when trying to prime the system but there is pressure to secondary filter on engine. I do not have a gauge and adapter to check the pressure yet. I did pick up a replacement pump before the parts dept closed. Could the pump still be bad even tho I do have pressure at the secondary filter?
View 1 Replies
So my 06 6.0 4x4 is just about to break 200,000km and I've done most of the upgrades and work myself. (All the updates are in my Sig). My problem is that when I'm cruising and the engine is at full operating temp, if Im bellow 80-100km/h nothing but as soon as I break into that speed range about 2000rpm the truck will start to shudder. Almost feels like its not firing properly is the best way to describe it. Why this could be happening or causing it?
View 7 Replies
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.
View 2 Replies
My wife and I went on vacation for our anniversary and the truck ran fine for a while then we went back to get ready and when we left it started up and everything seemed fine but it died about 200 yards later and is now cranking but not starting. Left my toolbox at the house (stupid!) And truck is new to me so I don't have gauge or reader. Checked the fuel filter under the hood and fuel pump is pumping. Any other tips on what to do that could be the problem without buying parts?
View 14 Replies
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 Replies
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 Replies
was driving and the truck started spitting and sputtering then I turned it off and started it again it died then I started it again and it died? fuse 27 was good fuel pump relay I think was good but I think the code was still on the truck so im not sure if it would let the truck start or not with that code thrown
View 1 Replies
I got a 2006 F250 6.0 that won't start. It turns over perfectly. What I've done so far was change oil and filter, along with fuel filters. All fuses and relays are fine. I payed for the scan gauge 2 and monitored FICM SYNC, FICM voltage, ICP, AND IPR. Every thing checks out besides ICP. The ICP is reading under 400. So I unplugged the ICP. Still no start.
I decided to spray some starter fluid in the intake and turn her over. Boom starts right up and runs fine. I even drove her around for about 20 min. I get home and shut off the truck. wait a few minutes and nothing dead again. So ICP is low but the truck runs fine after some initial support from starter fluid. What I need to do next? I don't want to have to take it into the shop for something stupid I could do myself.
Also the code its throwing at me is P0231 Fuel Pump Secondary Circuit
View 4 Replies
Late build 03 f350 auto, I got a p0500 code and noticed sometimes after 2rd-3rd gear engages theres a shudder or fast vibration for few secs unless i let off, it didn't start this till i took batteries out, where is the location of the vss at, I am seeing some say at each wheel, on top rear diff, on top back of trans so not real sure?
View 7 Replies
2006 long bed with LS diff sometimes gets a fairly robust CLUNK! sound and feel when decelerating with tow mode engaged. It only happens once per 20 trips and only about a mile down the road, and it only happens once in a blue moon. It definitely is the rear end making the noise and brief shudder. Otherwise the truck runs extremely well.
I had the pumpkin off and fluid changed with Ford friction modifier added at about 100,000 miles. Truck is at 160,000 now. I just got done with a trip in the mountains of Idaho carrying a truck camper and used tow/haul mode extensively for engine braking and climbing, worked like a champ. This was just one trip of many this summer. This is about the only thing wrong that happens on my truck, but usually occurs before I get very far from the house. Should I just forget about it?
View 4 Replies
I have a 2006 F250 with a 6 liter diesel I got about a hundred sixty thousand miles on it I've had it bullet-proofed haven't had too many problems with it I thought the fuel pump went out yesterday so I replaced it drove fine for a few hours then it started losing power and like it wasn't getting fuel and died I got it home took a test light and check for power at the fuel pump I don't have any positive or negative power ran a hot wire and a ground straight from the battery and hooked it up to the pump and it worked but when I plug the factory wiring back into it and turn the key on I don't have any power I checked the fuses they're fine...
View 6 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
Left the cap off my degas bottle after checking it this morning. Drove a couple hundred miles and it overheated and died. Cooled it off, filled it up with water out here, now it won't start.
When I first tried, before I got it full of water, it barely cranked. Now, it cranks fine, even sounds like it cranks too fast. But nothing. Did I really blow it this time? I don't have my ScanGuage.
Strangely, the oil pressure gauge registers normal as soon as I turn the key on, and stays there while cranking. I'm used to them starting at O, then registering after cranking a few seconds.
View 14 Replies
Today I was driving my 04 f350 6.0 I got to a red light when it turned green I hit the accelerator and it would not go it would only go about 10 so I limped to a parking lot and it shut down, it will crank and it sometimes Will start but only rev up to a grand then put in drive and it dies I had someone run me out a new pre programmed FICM and I replaced it right there and still will crank but won't run so I had it towed to a ford dealer and dropped my key in the drop box, what it may be?
View 11 Replies
Truck died going 50 mph and would not restart. I turn the key to run and nothing. I can hear the injectors buzzing but it will not turn over or crank. I can jump from the battery and the truck will crank. However, it seems to be in limp mode. It will start off in 3rd gear and won't shift gear Tow/haul light is flashing.
The wire harness that goes down to the fan clutch is chewed up and frayed so I'm assuming that may have caused an issue. But i have unplugged the sensor to the fan clutch and it still won't start. I can hear the injectors buzzing but when I turn the key to crank it, it does nothing. Just clicks. I've cleared the codes and these keep coming back.
View 14 Replies
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 Replies
2006 f350 6.0..... I was driving for about 10 hours and truck ran fine. Until with no warning it just died. Got it towed home and now I try to start. It turns over fine but no fire.... I know not to use but we used starter fluid to see of it would fire thinking maybe file filter bit still no fire with the starter fluid. I find it weird that it won't fire even on stater fluid. The engine oil was very low as well but since topped it up.
View 14 Replies
