Ford 6.0L Power Stroke Diesel :: 2006 - How To Get Out Thermostat From Housing
Apr 26, 2017
'06 powerstroke, 215k stock
Doing a coolant flush, took the thermostat out but cannot figure out how to get it out of the housing.
Apr 26, 2017
Advertisement
Ford 7.3L Power Stroke (1999-2003) :: Rounded Off Thermostat Housing Bolts
Tried to flush it and got as far as draining everything. I can't hook up my T and begin the flushing process because I can't remove the thermostat. I have a buddy who can get the bolt out but I'd have to be able to drive the truck to him. I've tried just about everything to remove it. I did manage to find some replacements for when I do get the last one out though .Is there a way to still flush this thing like maybe just hook up the hose to the t and run the engine with the heat on to open the thermostat?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - No Heat From Thermostat?
Went today to check out a buddy's truck, 06 F350 164k egr and cooler delete. He finally did his thermostat yesterday, after not having warm heat for months. Today on the way to work, had great heat for about 10 miles, then it went cold. Pulled over to check coolant, cracked cap loose, let pressure out, now had heat again. Same thing on the way home. Had the white streaks down from the cap, lost a small amount of coolant, just at min line now. He's owned this truck since 48k and no heads have never been off.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Thermostat Housing Broken Bolt - Replace Water Pump?
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Serpentine Belt Started Squealing - Coolant Leak Behind / Below Thermostat Housing
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
Ford 6.0L Power Stroke Diesel :: 2004 - How To Replace Thermostat In E350 Van
I bought a 2004 E350 van that has been driven 9000 miles in the past 6 years. Replacing a thermostat in an E350 6.0 Powerstroke van?
My van is running on the cold side ECT 176-180 when idling. It will reach 190 when I am driving. The EOT is 6-10 degrees higher.
I am flushing the system with Restore and plan to replace the T-stat soon when it arrives from Amazon. I have 3 gallons Cat ECT-1 full strength coolant and a lot of distilled and reverse osmosis water for the flush.
Is it a long procedure? There is not much room in a van to work with ease. If it's too involved, I will find some over time at work and pay my mechanic to do the install.
Ford 6.0L Power Stroke Diesel :: Bleed Air Out Of Coolant After Thermostat Replacement?
I'm about to replace my IPR and my thermostat, and just watched a video saying after replacing the thermostat you need to bleed the air out of the system to get rid of air pockets so you don't overheat the engine. Is this true and if so how do you do it? Also, how much coolant do I need to drain before taking off the upper radiator hose?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Housing Cracked?
]I am in the process of swapping my oil cooler. When i pulled the smaller cover off of the cover that goes over the oil cooler, i heard a pop. The cover, not the one that bolts onto the motor the one that bolts to that, is cracked...bad. is there a place i can get one? need to know parts illustration with numbers?
View 14 RepliesFord 6.7L Power Stroke Diesel :: DFCM Housing Broke?
I was twisting off the DFCM housing when I heard a pop and alot of fuel leaking. It appears I sheared off the 32mm plastic nut. I know for a fact that I was turning it counter clockwise just like the manual stated. Now what do I do? I cant run my SD can I? The simplest solution is to get another housing and install it but im not sure ill be able to get the remnants of the original housing off with out the nut to twist it. I watched Epics video on changing the filter and his came off with little effort? My same story just different result.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Bell Housing Drips Twice?
So I have a bit of an oil leak, bell housing drips once or twice while it is parked for a day or so and usually has a drip hanging off of it. Where the starter mounts also has some oil and there is some of the driver side. The valley is totally dry and I have new CAC boots so it isn't coming from up there. When I look through the inspection port it doesn't look like it is from the rear main. I figure this leaves either bedplate or cam/crank sensor. Any thoughts on how to narrow it down further? Maybe put dye in the oil? It looks somewhat oily up by the cam sensor but it is so hard to see that thing I can't tell very well.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Time For Thermostat / Stock Or Higher Temp?
Truck has an SCT tune from Innovative Diesel.
View 6 RepliesFord 6.7L Power Stroke Diesel :: Coolant Running Down All Over The Bell Housing And Oil Pan
The same day that I noticed my coolant temp was running high as I was driving around in my 2011, i was driving around in my corn field cutting wood and i noticed i was dragging something under the truck. when i got out and looked under the truck, there was coolant running down all over the bell housing and oil pan. i was a bit worried that it was my head gaskets leaking but once i got it in the shop and looked at the heads, all looked good. i wasnt sure where it was coming from! so i looked up common coolant leaks on the 6.7 on youtube.
First video was one of the coolant line on the turbo leaking. so i crawled up on top and shoved a mirror down by the turbo and sure enough i could see coolant leaking around the connector fitting coming out of the turbo. apparently the gasket goes bad around this fitting allowing it to leak. i was just wondering if this is really that common of an issue? I did the work myself. and its not really that hard to get to the turbo, its just time consuming removing all the crap around it. all i had to do was remove some connectors that were attached to the plastic intake and remove the intake then you can reach into that fitting. total time was around 2.5 hours.
Ford 6.0L Power Stroke Diesel :: Oil Leak Under Turbo Compressor Housing
I have a small oil leak that is showing up under my turbo compressor housing. It's starting to show a little in the valley. Not a big leak, just not sure were the source is and would like you opinions and recommendations. I have been cleaning it up every few days, drive it then use a mirror and rag to try and locate the source.
Here are some pics, I hope I took some that are good enough. Unfortunately I cleaned up the oil before the pics, but I circled and marked the location.
Concerned about the turbo, but I don't understand this leak since it's not coming from the center section. The turbo drain pipe is new and it does not seem to be coming from there. The leak is not enough to show a change on the dipstick the last 3-4,000 miles as far as I can tell.
Ford 6.0L Power Stroke Diesel :: 2005 F250 Running Really Cool / Thermostat Replacement?
I recently noticed my 2005 F250 6.0 was running really cool, like barely making it out of the 170's. I guess it is time to replace my thermostat which I just replaced about two years ago. The question is should I replace it with another stock 192 degree thermostat or go for a 200 degree Mishimoto? I found where some where going to that one and it is supposed to make everything run better and the thermostat lasts longer. Any pros or cons to installing a hotter one?
View 7 RepliesFord 6.7L Power Stroke Diesel :: Lower Fuel Filter Housing Broke
This past week my wife and I took a short trip and returned on a gravel road. I went to start my truck the next morning and there was a puddle of diesel fuel on the driveway. When I looked under it, I noticed that the tip of the fuel filter housing is gone and is leaking slowly from there. I called the dealer and they would not fix it on warranty, the truck has 20k on it. The service man said he would not turn this into ford. I've had the similar problems with this particular dealer. It's obvious that a protective cover is needed for this. I kept the part and am thinking of sending it to ford.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Major Oil Leak Accumulating On Top Of Housing
I bought a 2003 F350 with the 6.0L. It had injection, EGR, and oil cooler issues. I tore into it, did the injectors, EGR delete, new oil cooler, turbo seal kit, and several other non related things. Put everything back together and when I started it, it was leaking oil at the paste of 1/2 qt and minute. I did all sorts of searching on this site and went back to work on it.
I re-installed all new gaskets and O-rings, replaced the ICP and IPR sensors. Started it back up, exact same thing. From what I can see, oil is accumulating on top of the oil cooler housing around the area the turbo oil supply connects. But, its not leaking from turbo supply, or from where the filter housing attaches. Im at a loss. Its definitely somewhere on top of the engine and running down the back, only when the engine runs.
Ford 6.7L Power Stroke Diesel :: 2013 - Low Pressure Fuel Pump Housing Cracked?
This pump hangs down fairly low and appears easy for ice and rocks to hit on my 2013. Something hit mine and took a chunk out of the drain tube. No leaks yet but I am looking to get a new one and keep this as a spare, or just JB weld it. Can I just buy the lower section, or do I need to get entire pump?
Any creative protection bracket made? Would just have to take it off to change filter though. Any leak in this housing is a major show stopper when in the middle of nowhere! Maybe why it is getting brought into the tank on new models?
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Leaking Diesel From Fan Housing?
I'm presently traveling and my '02 F-250 with a 7.3 PowerStroke has developed a pretty steady drip of what I am almost sure is diesel fuel. It's dripping from the very front, from the shroud around the fan and radiator area.
I have some basic tools with me, but no experience on this engine or the fuel system. Does the fuel line go up into the radiator area? What should I be looking for? I'm stranded in a campground until I figure this out.
Ford 6.7L Power Stroke Diesel :: Coolant Leak Somewhere On Top Of Engine Running Down To Oil Pan And Bell Housing
I have a coolant leak somewhere on the top of the engine running down to the oil pan and bell housing. I have done some research and discovered it could be the coolant inlet tube to the turbo.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F550 - Inline Trans Filter Housing Seized
I went to change the small filter that is mounted just behind the radiator and is inline with the 5r100 . with a socket on the bottom all i was able to do was flex the brackets going to the 3 mounting bolts as this thing is on there real good. Looking for examples on unthreading the bottom cup to access filter?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Leak Appears To Be Coming From Secondary Fuel Filter Housing
I've got a leak that appears to be coming from the secondary fuel filter housing (the one in the engine compartment)... It's not coming from the filter, but from the side, where there are 4 allen bolts that attach a fitting to the side of the housing...Can I change out the gasket for that piece? I've already tightened the bolts, but the leak persists.
View 14 Replies