Ford 6.0L Power Stroke Diesel :: 2006 F350 - Lost Power Then Stalled And Would Not Restart
Apr 19, 2015
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
Advertisement
Fuel injectors do this? They are off a 2006 Ford F350 dually with the 6.0 diesel motor! Have replaced all 8 fuel injectors got back drove for 200miles and fuel injectors 4 and 8 were throwing codes changed them out and high pressure oil pump oil coolant deleted egr valve changed the ipr valve feed tubes to the oil rails. replaced the FICM. Yet again drove for 2 days about 200 miles again and shut down (stalled) misfiring hard start. and now fuel injector 4 is throwing codes again. Have not drove it since we got it home from the last stall out which was a few feet from our drive way and we towed it home.
View 5 Replies
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
View 2 Replies
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
Currently truck is in the shop after having multiple episodes where it lost power. It has 47,000 miles on it. When pushing down gas pedal, just does not want to go. Very slow to shift through the gears and get to highway speed. Turbo was not there, and there was also a hard shift/jerking from 2nd - 3rd. Did notice the traction control sensor kick on a couple of times....which was just replaced since a hole rubbed through the wiring. (took it to Ford twice before they found the problem)
They told me today that the code generator said to look at wiring but they did not find anything (heard that before) and that the fuel is possibly contaminated with DEF. If that is the case, someone is messing with my truck! What I don't understand that if the DEF does turn out to be in the fuel tank, wouldn't we have the problem continuously and not intermittently over a month after driving thousands of miles and going through numerous tanks of fuel? We drive and average of 60 miles per day just for work, half interstate/city.
View 14 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
My truck ran great when I got to my house that I turned it off and tried turning it on again it wouldn't turn on I check the fuel pump it works I checked the injector if it was getting fuel it was .I'm a stand still, where else to check? What to do?
View 14 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
View 11 Replies
I have a late model 2004 F-350 6.0 powerstroke. 182K miles. Auto Transmission
What happened. Condensed version
Left house, drove out to highway, got on highway. Everything feels normal.
About 1 mile of going 70mph, I notice I can no longer accelerate. after 1/2 mile, I begin loosing speed, and engine will not rev past 1000 rpm. I eventually pull over (another mile), put in neutral and will not rev past 1000. put in drive and start to idle to highway exit. it gets about another .5 mile and begin going up a hill when it completely dies. Will not restart.
No prior issues with the truck. Full tank of fuel.
What I have tested so far. Ficm 48.5 volts cranking. Icp .225V KOEO, .875V Cranking. LPOP is registering pressure on the dash. No Fault codes.
I have gotten it to start twice now, one time it allowed me to rev to 750 rpm, where i used 4 low to make it onto a trailer. second time would not rev at all. idling at 250-300 rpm.
That same night as it died, I drained the transmission pan/ TP filter and filled with 8.5 Quarts of Mercon LV. This is the first time I have done this since purchasing @ 161K miles. Everything seemed normal, no leaks present.
Also my buddy showed me how to enter the dash test mode and we cycled through these. Not sure if this is relevant.
So, What do I test next? I don't think its HPOP issue since the ICP is reading .875 volts at crank. I did unplug the ICP and it still would not start. I don't think its the injector side of the ficm because they buzz as normal with koeo, but this is a possibility as I don't have equipment to test. Egr valve is clean for age of truck.
Would it be possible that the Mercon LV knocked crud loose in the transmission causing it to fail/seize? would siezed tranny cause the engine to behave in this manner?
Fuel bowl on top of the engine was full of fuel. I have not pressure tested it yet as I can hear the pump running during key on.
could i have a bad crank or cam sensor?
Multi-injector failure?
Bad Icp with HPO failure?
View 14 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
Had my oil changed on my 2011 F350, and the tech said that I lost one gallon of antifreeze coolant. Where could the coolant have gone? We could not find a radiator or hose leak. I am afraid that the coolant somehow got into the engine oil, and may have damaged the engine. I have 46000 miles on the truck.
View 14 Replies
My 03 F350 lost the Brake Lights, and Code B1483 came up, which is the Brake Light Switch. Switch was replaced with new switch, with no change. The new switch was tested, and is working. The mechanic even replaced all the bulbs, which did nothing. The tail lights and turn signals work fine, just no brake lights. The mechanic even called the Ford Dealer in Boise, ID, and their service dept had no clue. What is everyone missing on this issue?
View 14 Replies
My 6.0 stalls when its warm and it restarts no problem. no codes are given with scan gauge. No changes on icp or ipr when it happens. At idle icp ranges 577 to 737, fmp 47.5 to 48v, ipr 23 to 28, map 14.9, tfc .32. all at idle. all increase when rpm goes up. ive done the d plugs, sct plug ficm replaced 2 yrs ago. done egr delete, need to trouble shoot? Again no codes given...
View 14 Replies
A friend brought to me this 06 E350 with a 6.0, which stalled on him while driving. The van will crank over good and strong, but won't run. It will how ever fire, and almost run until you let the key back (i would describe it as it does run with assistance from the starter). the FICM has 12V in and 47.5V out. And ICP is around 650 psi till it fires then it raises to 1215 psi. there are no codes either - I'm not familiar with these 6.0l...
View 13 Replies
So this '06 F350 is blowing fluid from the steering pump fitting when you move steering wheel to either side all the way(lock). Is the internal o-ring blown in the fitting? Do these have the teflon seal at the pump? Pretty new to the 6.0 scene. Got a new line ordered.
View 6 Replies
I have a 06 f350 superduty with a 6.0 I have had injector problems before with the motor even hydro locking no start this is the problem my truck started blowing white smoke with a strong diesel smell everyone said it was oil cooler but I took it to a ford garage the guy said I had 2 injectors hung open and wasn't hydro locking and suggested to put all 8 in so I did 3400.00 not I went to pick it up had no power at all turbo was not kicking in so I took it right back to them they checked it out said turbo was sticking had to clean it it would take 6 hrs. said the fuel In the motor caused it it was working fine when I took it to them now they say maybe a new turbo are they giving me the run around or is this possible....
View 9 Replies
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it). Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 7 Replies
My dad recently bought 2006 6.0. He has had it about 2 and half months. Has the egr delete kit installed. The truck has ran great. Up until Wednesday the 3rd. My dad headed to Ut to pick up our new quads. While heading up a small grade with empty trailer in tow. Truck went to limp mode, fan kicked on, orange wrench came on on dash board. He pulled over let her cool down turned her off.
Checked fluids Then started her back up and she was fine. That has happened 3 times. Now he is on his way back (tow haul mode turned on) and it is doing it again. She hasn't went into limp mode yet. As soon as the fan kicks in my dad pulls over immediately and puts it in park. And lets her cool down checks fluids. This issue only happens mid way up a grade. So my question is...... What is causing this? How do we fix her and make her a happy truck again.
View 7 Replies
I have a 2006 F250 with an International 6.0 turbo diesel. Last Friday I was driving 70mph up hill when my truck slowed down (I wasn't hauling anything) and then stalled, I got it restarted my doing a moving restart. After that it stayed in limp mode and wouldn't go up into 4th gear it just would jump from 1st to 2nd them to 3rd if I was coasting and it would only let me go 40mph at the most, so I got a tester and tested it and the only code it gave me was glow plug 1 & 5 were misfiring so I replaced those.
After I decided to do a test drive I went 800 meters and my tuck still didn't go out of gear one and I couldn't get my truck to go more than 5mph, then it stalled, so after about 30 minutes and 2 other guys tinkering with everything, we got her started and she sounded perfect, so I took off again, same thing happened except I got her going 20 mph but her RPMS stayed under 2,000 and then it decided to sputter and then stalled.
When I went to restart her the ABS, TBC and the transmission light went off, now she won't crank over and she was clicking (starter or dead battery) and now the lights don't go off, the Windows don't work and their is no electricity flowing...... I understand the electricity, she has 2 batteries. (The first one starts i.e. Glow plugs, starter etc, the other just supplies juice to the system, I.E. Lights, fuel pump.. Etc) what is causing this?
View 6 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
