Ford 6.0L Power Stroke Diesel :: 2006 F350 - Codes / White Smoke And No Start
Apr 14, 2017
We have two 6.0 trucks and one is having issues. A couple days ago it started to have white smoke like crazy upon startup, and when you slowed down you could see smoke, any speed and it dispersed so it was not noticeable. It got worse very rapidly and I haven't ha. A chance to work on it, it's also burning antifreeze, that's what the smoke is. Recently the egr started to act up so I cleaned it and the code for a sticky egr went away. It came back after a few months so I cleaned it, it went away for a few days then came on with the symptoms I just described. It has been moved at work a couple times the last few days, but not driven. Today I had to move it and it would not start, no white smoke either while cranking. I read the codes and this is what it has:
P0674- cylinder 4 glow plug control
P0404- EGR control circuit range/performance
P0299- turbo underboost
P0403- EGR control circuit
P0405 EGR sensor A circuit low
I would say it's a head gasket or EGR cooler, no? What course would I take to find out what's wrong? The truck in question is a 2006 F350 SRW King ranch. It has 115k on it, and the majority are work miles pulling trailers.
View 9 Replies
Advertisement
I would like the hear what others have to say about the problems I'm having with my 2006 F-350 sd xlt 6.0 with 113,000 miles on it. It's being used as a tool truck mostly going from a shop on the property to close by buildings on the same property. In other words very short distances. Used occasionally to take a dump trailer to a close by dumping ground.
1. White smoke from exhaust. I've read this is most likely an ERG cooler that needs replacing. Any other possible causes? If I end up having to replace the cooler is there a stock cooler that is reliable or should I get the one by bullet proof?
2. Diesel is dripping from the muffler weep hole. Last full tank lasted only 60 miles. Could this be the oil cooler? Anything else? If so is the Ford replacement cooler OK or should I go with an upgraded cooler?
View 14 Replies
Ok I bought a 2006 Ford F350 with 6.0 after driving for about 3 weeks I noticed a little bit of coolant was disappearing out of reservoir. So yesterday I was driving with a load Reservoir overflows replace coolant with one gallon of coolant and finish trip with no issues. I started truck today and it will not stop smoking it is also not overheating after hearing about head gaskets. I'm hoping it might be EGR cooler white smoke smells like raw diesel fuel. What to do?
View 3 Replies
I have a 2006 F350 6.0 diesel with 110K miles. it takes me about 10 tries to get the engine to start. When it finally starts there is a lot of smoke and engine runs really bad. This isn't the case if I have the engine warmer plugged in. After warm up the engine runs pretty good.
My engine light comes on sometimes and will go out other times. I have tried sever attempts at adding injector cleaner with no results. Am weary about taking it to Ford for an analysis. Where to start with repairs? I did take it to Orielly auto and had the engine checked on their scanner. Approximately two pages of possible repairs come up.
View 3 Replies
06' with 85,000 on it started smoking yesterday. When idling , and stopping at red light, and then sometimes it doesn't. Run it this afternoon for about 10 miles, let it warm up. Ran good and smooth didn't smoke when cranked then at the red light it started to put out a little white smoke. Drove back home, pulled egr valve and it did have a little wet on it, the coolant level has dropped some to. I scanned it and it didn't have any codes, no misfires or anything! Is it safe to say that the egr cooler has a small crack in it and its just starting to leak?
View 14 Replies
2006 blowing white smoke and sluggish until its driven for a few miles ..smells like fuel .. New head gaskets and the works started after 20 days over below freezing temps nights at 5 to -5 ....
View 14 Replies
My 06 6.0 is blowing a fair amount of blueish, whitish smoke only on initial startup, then continues to blow smoke slightly for around 10 min until it's warmed up. It seems to be getting a little worse as time goes on, only on startup though. truck has no other issues otherwise, has an egr delete, and some old edge tuner. I don't think it's head gaskets, no other symptoms.
View 6 Replies
I noticed about 1 year ago I had diesel in my coolant but wasn't sure.. took it to a Ford Guy about 45 minute's away.. He seems to know his stuff but when he tested the coolant the results said less than 2% diesel.. But he did find an injector issue and swapped it out..
Forward to present.. there is diesel in my coolant now , since the level is rising to almost overflow and I believe this has been doing on for quite some time as I have that smell you get in the cab..
BTW - All injector cups have been done about 3 Years ago.. On another note , I get white smoke on start up especially if the truck has sat for a day or 2.. What can cause diesel in the coolant.. I did a complete coolant flush this summer and was super **** about getting all the old coolant and gunk out.. Ended up with only clear water coming out the degas
View 14 Replies
I have a 2006 f350 with 75k on it, has a mild sct towing tune, and 4' turbo abck dual exhaust. It recently started blowing whiteish smoke, so i did an EGR cooler and valve delete kit, and it stoppe dsmoking for a while.. coinsidence?
It has recently started again, at idle there is no smoke, and taking off slow from a stop, it doesnt ALWAYS smoke. but leaving a dead stop, if i get right into it, it billows whiteish smoke, and if im cruising, romp on it, let off it, then get on it again it will smoke.
Ive been told fuel pressure, injectors, turbo seal etc. when i had the down pipe off, no sticky black residue was present, so im counting out turbo seal (for now). I purchased the blue spring upgrade for fuel pressure, because i was told its not getting the right amount of fuel, once i get that ill throw it in and see if it fixes it.
whats yall's opinion? is it worth have it checked for a failed injector? as i said, no EGR in the truck, no loss of coolant either, oil is clean. It does seem a little sluggish at times off the line now as well.
View 11 Replies
I just got a 2006 ford F250 lariat fx4,and it's already at the shop.. when cold start it has some white smoke, but once I get up to highway speeds the truck jerks and bucks. turbo is putting out normal boost. I've changed oil and filters along with fuel filters. also put on a new serpentine belt and pulley, air filter and have everything cleaned real good. the truck is acting like it's starving for fuel. FICM or injectors ?
View 14 Replies
I have a 2006 F350. It started running rough and white smoke from the exhaust. I did an injector buzz test and found no codes. Cylinder contribution check showed cylinder one was not functioning. I replaced number one injector, cleaned injector cup installed new injector and copper washer. Engine runs the same. If it was a wiring harness issue should that have shown up in the buzz test?
View 8 Replies
2006 overheats and starts blowing white smoke, smells like antifreeze, added 2 gals of water to make it 1 mile home. Smokes on the way @195 temp and when I shut it off it smokes out tailpipe for another 3 min. Smells like the head gaskets just went, what should I check? The eot and ect have been 10 deg or less.
This has 225,000 miles on it ran great before this, so would it be stupid too not get a redone set of heads while I'm doing the gaskets and studs?
I was thinking of getting heads from here, UCF Machine Shop - Precision machining, engine rebuilding and more. Cummins + Ford Rebuild Specialist. And a Sinister Diesel Complete Solution For Ford Powerstroke 2003-2007 6.0L. Are these the right places to deal with or should I look elsewhere?
View 14 Replies
I just bought an early 04 (01/04) and it starts hard when it's cold. It starts just fine when it's warm. It idles a little rough it seems and it's putting out white smoke, but not too thick. There are no codes on the truck.
I performed the "bubble test" and got no bubbles at all. I have found that it is common for oil rail o rings and dummy plugs go bad and I'm being told that is what the problem is.
Could the oil rail seals be the problem? It makes sense to me only because there are no codes and I feel anything else would have thrown a code.
View 8 Replies
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it). Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 7 Replies
I have a 04 f350 with 175k on it. At around 160k it had new head gaskets, 2-reman heads, egr delete, new oil cooler and it is studded and tuned with SCT and custom tunes.
Since after the head gasket change it seemed to have started blowing a little smoke on the cold starts mainly. In cold weather the starts seem to be harder or slower also. Now for the last 6k-8k miles there is a little smoke at a cold start. But if the motor is warm and it sits for a bit maybe 10 min or less it blows a nice puff of blue smoke or burnt oil.
The smell of burnt oil is mainly on hot starts not cold starts. It does not burn oil running. It will dump some black smoke under acceleration or load. Could this be an injector problem? Or something else? Can't figure it out.
View 5 Replies
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 Replies
2007 6.0 6 speed, 187,000 miles. The other day started truck, had been running about 20 minutes before. Started fine, go to drive, chugging white smoke, smelled like unburnt diesel, baby truck home, seemed to run ok at low rpm, truck warmed up and ran fine. But I also noticed turbo boost was acting funny. Truck ran fine next few days. Then this morning, started cold fine, started to drive it and same chugging white smoke, it quit by the time j got to the end of my driveway, but drove to work, it quit smoking, ran pretty smooth, but will not build any boost. Truck is bone stock except for exhaust, it's straight piped. Ok. So this eve I borrowed my dads edge cts, here's all the engine codes:
P0069
P0269
P0299
P2262
P2269
The last one is water in fuel, since it started this crap I did notice it was right after it came on in the dash. I'm trying to figure out where to start....
On another note. VGT duty shows 85% at idle ?
Ficm voltage is constant 48 volts
Newer batteries
View 14 Replies
no change, changed stand pipe and dummy plug on driver side, no change and guess what? Now I am stuck on the side of the road waiting to give my last $100 to a tow truck! Engine is hydrolocked, fuel pressure is low, starts off at around 20 and works up to 54 with key on engine off, and that is as much as I know from the side of the road with out my AE. Blew white smoke also. Smelled of unburnt diesel. I think it's linked to my rough running issue. Maybe a bad injector? But every time I did the click test they all passed. Idk, I'm gonna remove the glow plugs and see which hole is loaded and with what. . .
View 14 Replies
yesterday I went out started my truck and white smoke started coming out my exhaust so I turned it off waited a bit started it back up let it run for a bit smoke went away drove it about 60 miles. Later that night it did the same thing but I was 2 gallons short on coolant drove it another 60 miles ran fine. Next morning decided to take it to a shop put more coolant in it drove maybe 20 miles to shop got there turned it off everything was fine never over heated once. So this shop is now telling me my trucks hydro locked and I steamed the EGR valve. And there telling me it's gonna be $8000 to fix it .
View 3 Replies
I have a 2006 Ford F-250 6.0 powerstroke with 100,000 miles and it puts out a puff of smoke at cold start up every time and also when I run it then park it for maybe 1 1 1/2 and it puts out a puff and also I noticed when I get to work with is about a 20 minute drive I get there around 8 then leave at 5 I noticed it puts out a puff then if I watch the exhaust I can see a slight haze but I figured it's just condensation.
Here's the list of stuff I have put on the truck... Oringed heads by librator performance, with oem gaskets every thing, arps head studs, egr delete, airdog 2 fuel system,mtw stage 2 turbo, bulletproof ficm,coolant filter, banks intake, fuel pressure set at 68 and fuel regulator return.
Here's a list off parts I put on trying to fix the smoke I put in 5 injectors because the ford ids had a slight change and after that it was straight line I put in hpop and turbo drain pipe and I tested the ficm and its 48 with the key on and cranking and running...
View 14 Replies
I have a 2006 Ford F-250 with the 6.0 with 99,000 that puts a puff of white with a tint of grey that smells like unburnt diesel smoke at start ups it will do it cold ever time and will do it when i let it sit for maybe a hour but not every time. I've noticed I had higher egts then before also not sure if it's related at all or not. I had on the ids the graph was a straight line for the injectors, pressure checked the coolant cold and hot doesn't loose pressure. No puking, New hpop. Here's what I have done to it, oringed heads,arp studs,remote oil cooler, factory injectors,egr delete,air dog 2 fuel system, coolant filtration, bulletproof ficm, regulated fuel return, stage 2 mtw turbo,CCV mod, banks air intake. I'm stumped!
View 14 Replies
