Ford 6.0L Power Stroke Diesel :: 2006 F350 4x4 Won't Move - Trans Busted?
Oct 28, 2016
I have a 2006 F350 4x4 dually (6.0 diesel obviously) automatic. It's got 200kml on it and a second motor (found the sticker on the valve cover). I just bought it a month ago and have only driven it like 100-150 miles. Previous owner imported it to Finland 3 years ago, but never registered and only drove it like 500-1000 miles (with temporary plates to carry his racer few times). Original owner was a company in Southern Midwest that had some equipment on back. (It's was sold as a chassis cab new.)
Now I was getting the truck tested for registration yesterday. Drove it there 30 miles (country roads and highways), no problems. Then we had to do the smog-test, which is a bitch. They rev the engine to limiter (4200rpm) couple of times and measure the particles flying out. Passed it flying colors, but when trying to pull out the transmission wont engage!
Shifter linkage ok. Oil in tranny clear and plenty. When I put on R or D the engine RMP rises very slightly (maybe 50-100 rpm) and then settles back. But nothing else happens.
Luckily got a friend with large flatbed that we used to carry my baby home. But now I don't know where to start... ...well, I do have couple of ideas what could be broken. Specially if there's something simpler than dropping the whole tranny out (it's HEAVY and it's cold&wet out there) and rebuilding the whole damn thing.
Previous owner told he had some shifting issues couple of years ago (maybe 500 miles ago) and they "rebuilt" the tranny. He DID replace the hydraulic "logic board" and solenoids + new packs while at it. Naturally new filter & oil too. He said the torque converter was "tested" to be in good condition and they used the old one. I can tell the tranny has been out of the truck and the seller felt legit (a car guy too).
View 14 Replies
Advertisement
I have a 2004 6.0 with the 5L110 transfer and torqueshift transmission. While test driving after installing everything, I didn't get 7 ft down the road and the tires locked up and she came to a dead stop. Now I only have reverse but I can still feel the tranny engaging into drive but will not move.
View 2 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
View 10 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
Took my '11 F350 CC 6.7 Lariat with 31k miles on it into the dealer to have the tranny fluid leak looked at. I noticed this leak a few weeks ago as the bell housing was damp with fluid and the bolts heads on the underside of the poly engine oil pan were pooled with fluid. It is a very slow leak as I have parked it for 3 days and there were no drips of fluid on the ground, just collecting on the grid like pattern on the oil pan. Checked Fluid level and it is also full.
Anyway, the dealer put dye in the tranny fluid and told me to drive it for a few days. I took it back in on Monday and called this morning for an update. The mechanic informed that they ordered a new torque converter and some other parts to be "proactive" because he believes the TC is the issue. I asked if the cab would have to be pulled and they informed that all the work could be done from underneath. Glad I noticed this before the B2B warranty expired because this would have been expensive. I will be THOROUGHLY inspecting the entire vehicle from top to bottom before I hit 36k.
View 11 Replies
My Father In-law has a 2012 f-350 Dually with 4K miles. He tows a 9K lb camper and until our last trip the truck ram flawlessly. On our return from Myrtle Beach to central NC we were on a freeway traveling at 63 MPH and his tranny would not shift into 6th gear. Tow haul was on. There was some headwind (10MPH) but no large grades or any reason we can think of not to allow an up shift. His display did show a countdown to empty of the exhaust fluid 450 miles to empty.
He took the truck in for service and no codes were found. Dealer did not find any TSB's addressing the tranny issues. Is the sixth gear up shift in tow haul set very conservative? Does it hold 5th unless the load is below a certain value? Other trips we have been on have been mountain towing so 6th gear shift would have been on down hill or level sections. Dealer wants us to bring it to them when it won't up shift next time but dealer is not along a freeway.
View 14 Replies
Bought this truck (06 F250 cclb diesel) earlier this year and (as far as the seat is concerned) worked perfectly until about 2 weeks or so ago, when I learned that the passenger power seat works in every direction except for to move the seat back. Since every one that got in the truck didn't believe me and now the seat is almost at the glove box I finally decided I should do something about it. I have removed the fuse and let is sit with the the fuse out for about an hour, no change. I had read on another fourm that if you recline the seat back a few times it resets the module, attempted with no change. It is to the point I need to get into a bit more serious diagnostic processes however I am unsure exactly where to start.
View 2 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
I would like the hear what others have to say about the problems I'm having with my 2006 F-350 sd xlt 6.0 with 113,000 miles on it. It's being used as a tool truck mostly going from a shop on the property to close by buildings on the same property. In other words very short distances. Used occasionally to take a dump trailer to a close by dumping ground.
1. White smoke from exhaust. I've read this is most likely an ERG cooler that needs replacing. Any other possible causes? If I end up having to replace the cooler is there a stock cooler that is reliable or should I get the one by bullet proof?
2. Diesel is dripping from the muffler weep hole. Last full tank lasted only 60 miles. Could this be the oil cooler? Anything else? If so is the Ford replacement cooler OK or should I go with an upgraded cooler?
View 14 Replies
So this '06 F350 is blowing fluid from the steering pump fitting when you move steering wheel to either side all the way(lock). Is the internal o-ring blown in the fitting? Do these have the teflon seal at the pump? Pretty new to the 6.0 scene. Got a new line ordered.
View 6 Replies
I have a 06 f350 superduty with a 6.0 I have had injector problems before with the motor even hydro locking no start this is the problem my truck started blowing white smoke with a strong diesel smell everyone said it was oil cooler but I took it to a ford garage the guy said I had 2 injectors hung open and wasn't hydro locking and suggested to put all 8 in so I did 3400.00 not I went to pick it up had no power at all turbo was not kicking in so I took it right back to them they checked it out said turbo was sticking had to clean it it would take 6 hrs. said the fuel In the motor caused it it was working fine when I took it to them now they say maybe a new turbo are they giving me the run around or is this possible....
View 9 Replies
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it). Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 7 Replies
My dad recently bought 2006 6.0. He has had it about 2 and half months. Has the egr delete kit installed. The truck has ran great. Up until Wednesday the 3rd. My dad headed to Ut to pick up our new quads. While heading up a small grade with empty trailer in tow. Truck went to limp mode, fan kicked on, orange wrench came on on dash board. He pulled over let her cool down turned her off.
Checked fluids Then started her back up and she was fine. That has happened 3 times. Now he is on his way back (tow haul mode turned on) and it is doing it again. She hasn't went into limp mode yet. As soon as the fan kicks in my dad pulls over immediately and puts it in park. And lets her cool down checks fluids. This issue only happens mid way up a grade. So my question is...... What is causing this? How do we fix her and make her a happy truck again.
View 7 Replies
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
This truck is bone stock FYI. I get in it to crank it and I get nothing. Batteries are good, everything in the cluster lights up, and looks normal. No codes are thrown. I can hear the solenoids click under the dash and hood. I check the voltage of ignition cable at the starter and I get no reading.
There is a single thick yellow with light blue stripe coloured wire on the passenger side of the engine compartment, beside the vacuum pump with a "squeeze and pull" type disconnect. Disconnect it, and connect the male half of the connector to the passenger side battery positive terminal. Do this with the ignition key in the RUN position. Does the truck start?
This is where it gets weird. The truck does start and after i reconnect the wire it it starts normal. I started it several times throughout the day. The next morning I get in the truck. No start. I have to use the wire and manually connect it to the battery and it starts right up again. This time I get a "Tow/Haul" light blinking on the dash. It will go into gear but pressing the acceleration pedal does nothing. I turn it back off, attempt to start it normally and it starts right up. No it will go into gear and drive. Now I am thinking maybe the neutral safety switch?
Could it be a solenoid sticking or the neutral safety switch or something else entirely?
View 14 Replies
I have a 2006 6.0l f350 crew cab that blows air hard every time I accelerate. Sounds like you're going 100mph with the hood unlatched. It blows real hard for a minute and goes away if I accelerate through it or let off.
View 7 Replies
I was just wondering, is it normal when plowing to get stuck in the snow? Last year I got stuck and had to get pulled out, yesterday I got stuck again and when I have it in 4x4 hi, one front and one rear wheel spins. 4x4 low, the opposite front and opposite rear spin from hi. I want ALL 4 WHEELS TO SPIN! I'd NEVER get stuck if that happened! How do I get that to happen? I hear of a detroit locker. Do you need one for each wheel? I always thought as I was flying past everyone in the snow with a huge smile on my face, that all of my wheels were powered.
View 14 Replies
Went today to check out a buddy's truck, 06 F350 164k egr and cooler delete. He finally did his thermostat yesterday, after not having warm heat for months. Today on the way to work, had great heat for about 10 miles, then it went cold. Pulled over to check coolant, cracked cap loose, let pressure out, now had heat again. Same thing on the way home. Had the white streaks down from the cap, lost a small amount of coolant, just at min line now. He's owned this truck since 48k and no heads have never been off.
View 8 Replies
I bought an 06 6.0 f 350 4x4 dump bed cheap. seller said it was sitting for 1-2 years and wouldn't start. ficm is at 48 volts fuel pressure is at 100 oil pressure builds fine, then checked compression and reading no compression in any cylinder. My mechanic says new motor or possibly both head gaskets are blown.
View 14 Replies
2006 F350 6.0 ... I am piling up parts for a bulletproof party later this summer. It has gotten grumpy ahead of schedule. I will hook up the AE tomorrow for consultation.
In the meantime. Running rough at 50. Seems to accelerate from a stop semi ok. Sitting at idle, holding rpm at 1750 I hear kind of a thump under the hood and the rpm drops 300, then slowly finds it way back to 1750 and it repeats itself.
This thump has not been noticed in the past. Could this be the VGT not working as expected?
View 4 Replies
I have a 2006 F-350 4x4 CC LB. I recently had my check engine light come on coincidentally on my way to the auto parts store. Asked them to plug in the scanner and read the code. It had around 20! This truck has 40000 miles on it. All of the codes were dealing with injector voltage being low. All eight cylinders. So I'm thinking ficm is going out. I replaced the batteries shortly after this. I driven it a time or two after this and it started cutting in an out going down the road. Seemed down a few cylinders for a few seconds and pouring black smoke from the tailpipe of a stick truck. Made it home after it did this there times. Stated it up to move it a few days ago. Some white smoke that clears quickly and ran rough for a few, pulled it in gear surged forward and died. I cleaned the EGR valve and re o ringed it. Tested the drivers side pin on the FICM and have 47-48 volts with key on and cranking.
View 4 Replies
