Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start - ICP Is Low - Code P0231
Aug 30, 2015
I got a 2006 F250 6.0 that won't start. It turns over perfectly. What I've done so far was change oil and filter, along with fuel filters. All fuses and relays are fine. I payed for the scan gauge 2 and monitored FICM SYNC, FICM voltage, ICP, AND IPR. Every thing checks out besides ICP. The ICP is reading under 400. So I unplugged the ICP. Still no start.
I decided to spray some starter fluid in the intake and turn her over. Boom starts right up and runs fine. I even drove her around for about 20 min. I get home and shut off the truck. wait a few minutes and nothing dead again. So ICP is low but the truck runs fine after some initial support from starter fluid. What I need to do next? I don't want to have to take it into the shop for something stupid I could do myself.
Also the code its throwing at me is P0231 Fuel Pump Secondary Circuit
View 4 Replies
Advertisement
Okay, I am having issues with a 1999 F250 XLT 7.3 with diablo programmer. I have searched and searched and have tried everything we could think of and it is a no go. The truck will crank, hesitate to start, start and die, other times it will only crank and not run at all. We can make it stay running by hitting the accelerator. The only code we were getting was the cps code, but that is suspected to be because of the excessive cranking and no start times. Previous to this issue getting this serious it would stall randomly, at idle, going down the road at constant speed, slowing down, or accelerating. We now have code P0231.
Through this we have tried:
IDM
(loaner) ECM
removing Diablo
3 CPS
shaving down CPS
Shimming CPS
IPR
Fuel pump
relay
fuel pump fuse
View 3 Replies
6.0 diesel 83,000 miles. My CEL is always on and my Edge gauge says it's lower than expected Mass air flow. I've changed the filter, cleaned the MAF with special cleaner and then replaced with new. I've replaced the EGR valve.
If I clear the codes and run it I don't get a CEL until I turn it off. But the next time I start it, there it is again. My Edge reads 0.0-0.3 MAF while running but what that means. One end of my cleaner box is slightly warped but I can't feel any noticeable leakage.
Everything runs fine but I would like to regain the ability to have that idiot light available to tell me if I have a new problem.
View 8 Replies
My 2006 F-250 6.0PSD has a new hitch. Tonight it would not start once hot. It cranked and cranked but no start. My scanner showed ICP readings of 366PSI during cranking. Far below the 500PSI needed before the computer will fire the injectors.
So is this the STC fitting at the HPOP that is failing? If so how long will she start cold and drive normal before she leaves me stranded? I have the fittings and new dummy plugs and stand pipes as well. I was waiting to to do this work until I had the money for an new EGR cooler and oil cooler.
I know my oil cooler is failing as my deltas are showing a 15-19 degree spread over my coolant temps.
View 14 Replies
06 6.0 F250 throwing code P0677 #7 glow plug circuit module. I don't think one bad plug would cause a no start, however coupled with too much oil possibly? Swapped my oil about 500 miles ago, I put in 20qts accidentally, drained off about 3-4 qts eyeballed, truck fired up and ran fine no smoke nothing. Yesterday morning I was leaving work and moved my truck from parking space to behind the bay at my fire station, I turned the engine off.
Loaded up my gear and turned the engine to the aux position and someone was talking to me so inlet it sit for a while in the auxiliary position. Went to crank no start, turned the key off then back on and it fired. Fast forward after 7 different starts throughout the day, I'm at dinner with my son we go to leave engine will not start at all, rolls and rolls and rolls nothing. Towed her home and scratching my head. Over filled oil with a bad plug cause no start??
Egr delete, new oil cooler, cat and muffler delete, upgraded Y turbo pipe. Also have an SCII throwing codes p0677 and p0401 egr code....
View 14 Replies
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 Replies
I have a 2006 Ford F-250 6.0 powerstroke with 100,000 miles and it puts out a puff of smoke at cold start up every time and also when I run it then park it for maybe 1 1 1/2 and it puts out a puff and also I noticed when I get to work with is about a 20 minute drive I get there around 8 then leave at 5 I noticed it puts out a puff then if I watch the exhaust I can see a slight haze but I figured it's just condensation.
Here's the list of stuff I have put on the truck... Oringed heads by librator performance, with oem gaskets every thing, arps head studs, egr delete, airdog 2 fuel system,mtw stage 2 turbo, bulletproof ficm,coolant filter, banks intake, fuel pressure set at 68 and fuel regulator return.
Here's a list off parts I put on trying to fix the smoke I put in 5 injectors because the ford ids had a slight change and after that it was straight line I put in hpop and turbo drain pipe and I tested the ficm and its 48 with the key on and cranking and running...
View 14 Replies
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
View 11 Replies
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 Replies
I have a 2006 Ford F-250 with the 6.0 with 99,000 that puts a puff of white with a tint of grey that smells like unburnt diesel smoke at start ups it will do it cold ever time and will do it when i let it sit for maybe a hour but not every time. I've noticed I had higher egts then before also not sure if it's related at all or not. I had on the ids the graph was a straight line for the injectors, pressure checked the coolant cold and hot doesn't loose pressure. No puking, New hpop. Here's what I have done to it, oringed heads,arp studs,remote oil cooler, factory injectors,egr delete,air dog 2 fuel system, coolant filtration, bulletproof ficm, regulated fuel return, stage 2 mtw turbo,CCV mod, banks air intake. I'm stumped!
View 14 Replies
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 Replies
I just picked up a 2006 F250 6.0. It was having hard starts. Anyways before I started using it I started tearing things apart cause I knew for sure the turbo was leaking so that had to be resealed. I just picked up a 2003 turbo today for it out of a used truck that had 144000 kms on it. (was in an accident). I am gonna post up a few pics here of the engine bay area, there is a huge amount of old oil I believe to be, I am wondering if it was a leak or spilled oil. I am going to be cleaning this up. Putting 03 turbo in here, doing a service and then plug my Tablet with torque pro and post up some numbers and see how healthy she is. Before I post any pics Is there a way to make these pictures clickable instead of them taking room up on the page?
View 14 Replies
I have a 06 6.0 no start . I was at a light felt a slight shudder went to take off felt another shudder and it just died. Changed fuel filters, unplugged icp no start still. No code at first now throwing p2291. Fuel pressure is at 62 when cranking. Hooked up air to the icp port and only heard air coming out of both valve covers inlets. Ipr was at I believe 60 to 65% when cranking. Little back round 2 years ago I did the whole sinister diesel top end kit and put the updated parts in. New o rings on everything that took them, new egr valve, standpipes and dummy plugs. On the injectors all new o rings and crush washers. I believe that's everything.
View 11 Replies
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
I am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
View 2 Replies
Ok just bought a '04 F250 Diesel. Loving everything but can't get the keyless code to work. The keypad lights when I touch it and I have retrieved the 5 digit code from the "Bosch" box behind the radio. No deal. Locks don't react at all to the factoy code. Know what? I read that there is a list of all the possible codes. Where can I get that list?
View 14 Replies
Bought a 2011 F250 with P1635 code. It has 35x12.50 tires my Sct x4 tuner only goes up to 34 inch tires. Im new to the 6.7 diesel game previously had 6.0 and want to hear from yall what to do.
View 1 Replies
I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 Replies
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
I have an 06 F-250 with 122,000 miles. When driving empty at 70-75 mph the coolant temp runs 194-200 and the oil temp 5 to 10 degrees higher at the most. When I pull my travel trailer the coolant temperature will start to steadily climb then abruptly drop down under 200. I have seen the coolant temperature pass the oil temperature when this happens.
The last time I pulled the trailer I was driving at 60 mph and the coolant temperature climbed to 220 then dropped to 196. A few miles later it climbed to 230 then dropped to 200. While the temperature was climbing I slowed to about 45 mph. As it was dropping I accelerated and the temperature continued to drop.
I have flushed the cooling system, replaced the thermostat and cap with no improvement.
The pickup has an SCT tuner set to street 1 and I was told by the previous owner that the egr was deleted, but the stock egr cooler is in place. It is possible that a plug was put in. I pulled the egr valve and the carbon coating on it is gooey like it has been wet.
View 12 Replies
