Ford 6.0L Power Stroke Diesel :: 2006 F250 - Rough Start And Idle When Engine Cold
Mar 10, 2015
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
Advertisement
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
View 14 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 Replies
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 Replies
I have been debating if i should use seafoam engine treatment. My truck has been having issues with the first cold start of the day. I've noticed the rough idle that accompanies the cold start. I live in Denver so this truck sees alot of stop n go traffic. Will seafoam do anything about the dirty fuel injectors. They have to be replaced here soon but will adding seafoam solution buy me more time. If so, what are the steps on how to add. The can isn't very detailed on instructions and Internet isn't being useful. I have an 04 F250 Lariat Power Stroke 6.0L diesel
View 14 Replies
My '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
View 6 Replies
I have a 2006 f-250 6.0. About 2-ish months ago, it started revving up while I was parked and hooking up a trailer. It ended up needing an ICP sensor and pigtail wires. Was fine after that until around 10 days ago, it died when I was driving down the road and wouldn't start back up. That time it was the IPR. Got it back Friday, drove home (40 min) and didn't need to drive it until today. I fired it up, and we're back to the revving/surging. I decided not to take it on the road, really tired of being stranded. Could it be the icp again? Something else? I'm so tied of throwing money at this thing.
View 7 Replies
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 Replies
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 Replies
I have an 05 f250 6.0. We have started to reach 38 at night here in northern IL already. The trucks been having a rough time starting and it's not even that cold yet. Any recommendations on the truck that I can do to have easier starts. Sometimes cycling the glow plugs 4 5 6 7 times isn't enough to get her going. I plug it in most of the time on bitter days in the winter but sometimes I leave it parked where I cannot plug it in. The batteries seem just fine. I think one is a little weaker so I will get new batts.
View 6 Replies
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies
I'm having a bit of a cold start issue, need to know if it is normal or something is wrong. I live in southern Indiana and it's gotten down to a VERY cold 50 degrees (lol) and the past two mornings I have started it up and it seems to have a misfire first thing in the morning and it will kick into high-idle mode and after I shut it off and start it back up about 20 seconds later after the ECT gets above 100* and it runs perfectly. It has brand new 190/100 injectors from Warren, an IDP tune, and I am running 13 quarts of FoMoCo 15w-40 oil with 2 quarts of hot shot stiction eliminator (tried it before installing new injectors). And also throwing no codes. Is this normal or should I be looking for a problem?
View 13 Replies
So after replacing all injectors, I was getting a rough idle and drive. Got an imbalance on 5 & 4. Cleared out codes and 5 still showed. The guy doing my work and I couldn't trace it to anything so we thought well maybe we got a bad one. Did fail the buzz test. So got a warranty one and put in. Wouldn't you know it's still not running quite right. Only thing we can think of is maybe the ficm is at the start of going out. Voltage reads good still though. Staying constant at 47/48. Is more noticeable to run rough when starting from cold then smooths out but you can still make out/feel an injector going in and out.
View 14 Replies
My 2003 7.3 f250 has trouble starting whenever the temperature is less than 65 degrees. If it is less than 50 degrees I have to plug it in for it to start. Once it starts it runs rough. I let it warm up and it still runs rough. Once I start down the road I'll get on it a bit and it takes off like something lets loose. It then runs geat for the rest of the day but does seem to still crank a little more than it should when I restart it through out the day.
The pickup has 152000k
List of repairs I have done to the truck:
-new gpr
-new glow plugs
-new uvch both sides
-new valve cover gaskets
-new blue cps
-new fuel filter
-new batteries everstart maxx 65n
The truck has an afe air intake, straight exhaust, and a super chips tuner set on mileage saving. It blows white smoke when first started but clears up pretty quick.
View 13 Replies
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 Replies
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
View 14 Replies
I have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
View 1 Replies
Just bought a 2006 F250 with 6.0. A week or so ago, it surged once at idle at a light. Sort of felt like someone bumped into your rear. It has gotten more frequent over the last week or so. Now it does it often. It tends to rev up and then back down again over and over. Then it will clear up again. My brother said his 7.3 used to have a similar problem (as did quite a few others apprently) and it was the Cam positioning sensor (CPS). Where is it located?
View 14 Replies
Fast idle 6.7 when cold remote start. My GM had what could be called a auto fast idle when it was cold it idle a lot faster.
It appears my 2012 f350 does not , Ford dealer said he could install a fast idle using one of the switches.
And then if I park truck with park brake on and switch on it when I start it will fast idle to around 1300.
My question is being if truck is started by remote , will not this switch be off and by being off fast idle will not work , is this not the case?
View 9 Replies
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
View 14 Replies
