Ford 6.0L Power Stroke Diesel :: 2006 F250 - Engine Revs Up At Idle
Aug 15, 2016
I have a 2006 f-250 6.0. About 2-ish months ago, it started revving up while I was parked and hooking up a trailer. It ended up needing an ICP sensor and pigtail wires. Was fine after that until around 10 days ago, it died when I was driving down the road and wouldn't start back up. That time it was the IPR. Got it back Friday, drove home (40 min) and didn't need to drive it until today. I fired it up, and we're back to the revving/surging. I decided not to take it on the road, really tired of being stranded. Could it be the icp again? Something else? I'm so tied of throwing money at this thing.
View 7 Replies
Advertisement
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
Just bought a 2006 F250 with 6.0. A week or so ago, it surged once at idle at a light. Sort of felt like someone bumped into your rear. It has gotten more frequent over the last week or so. Now it does it often. It tends to rev up and then back down again over and over. Then it will clear up again. My brother said his 7.3 used to have a similar problem (as did quite a few others apprently) and it was the Cam positioning sensor (CPS). Where is it located?
View 14 Replies
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 Replies
04 f250 364000 miles 06 6.0. New fan clutch. Ac didn't work when I put the engine in found out the fan clutch was bad so I replaced it. Now it doesn't turn at idle until the engine warms up even if I have the ac on. In the mornings it comes on and keep the temp at 190. In the after noon when if finally comes on truck runs at 210 to 190. Fss 530 when on at 210 at idle. And 800 at 1200 rpm what is going on.
View 3 Replies
I am looking for answers on a 2006 F250 with a 6.0, at a little over 200,000 miles. Currently I have taken it to two separate dealerships in the area with absolutely no results. The truck drives fine, starts fine, and for the most part, runs great. Except when it dies. It dies with no warning, at anytime. Warm, hot, cold, on the interstate, back road, driveway, where ever. It doesn't stutter, miss or signal, just quits running. Both dealerships have kept it for weeks, and driven it daily, and of course, then it never skips a beat. No codes have showed up that would cause the stall, and they are baffled.
View 4 Replies
I've got an issue with my truck, I was towing home my camper this weekend and my engine started missing out and vibrating very bad, then it overheated... pulled over and check codes, p0263, p0299, p0300, p0301. Oil all over engine, tons of blow by, definitely a dead miss on cylinder 1. Smokes bad out of exhaust, zero power, and blows cap off of oil filler when loose, tons of smoke and oil from ccv.
My question is, could it be in the valve train? Or is it going to lie in the piston/rings? Blown head gasket? It did overheat, but didn't puke out of bottle, turbo timer kept it running for a bit after I shut it down roadside, egts were definitely high. Also the egr is deleted, have a predator programmer with custom tune for she delete.
View 14 Replies
I have a 2006 f250 with 120k. I am having trouble getting the water in fuel light off. I drainned the water out and replaced both filters and the fuel water sensor. The check engine light is now on and the water in fuel light is as well. I'm stumped and can't figure out what to do next. Will the check engine light come on as well with the water in fuel light or is it two different problems?
View 2 Replies
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 Replies
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
View 14 Replies
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 Replies
I have a friend with a 2012 F250. The truck has 100K miles and it does idle for extended periods. The other day his check engine light comes on so he took it the shop. They had not told him anything yet, but they did tell him that he had about a gallon to much oil. They said it was fuel.
View 7 Replies
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 Replies
My friends 2004 6.0 f250 has 280000 miles on it and it runs perfect "did" until I tuned it with my sct tuner to run a looney tune so he could see what it was like. The truck started he revved it up to 3'000 rpm then when it returned to idle it acted like someone shut the key off. The high pressure oil system is new and has 700 psi and the icp is good also the ipr. The truck Is not getting any fuel at all, no smoke from cranking at all. It is returned to stock and is still being difficult. It has fuel I checked the upper fuel filter, it has enough oil, and it also has a good motor just don't fire. Why?
View 3 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
I have an 06 F-250 with 122,000 miles. When driving empty at 70-75 mph the coolant temp runs 194-200 and the oil temp 5 to 10 degrees higher at the most. When I pull my travel trailer the coolant temperature will start to steadily climb then abruptly drop down under 200. I have seen the coolant temperature pass the oil temperature when this happens.
The last time I pulled the trailer I was driving at 60 mph and the coolant temperature climbed to 220 then dropped to 196. A few miles later it climbed to 230 then dropped to 200. While the temperature was climbing I slowed to about 45 mph. As it was dropping I accelerated and the temperature continued to drop.
I have flushed the cooling system, replaced the thermostat and cap with no improvement.
The pickup has an SCT tuner set to street 1 and I was told by the previous owner that the egr was deleted, but the stock egr cooler is in place. It is possible that a plug was put in. I pulled the egr valve and the carbon coating on it is gooey like it has been wet.
View 12 Replies
My 2006 F-250 6.0PSD has a new hitch. Tonight it would not start once hot. It cranked and cranked but no start. My scanner showed ICP readings of 366PSI during cranking. Far below the 500PSI needed before the computer will fire the injectors.
So is this the STC fitting at the HPOP that is failing? If so how long will she start cold and drive normal before she leaves me stranded? I have the fittings and new dummy plugs and stand pipes as well. I was waiting to to do this work until I had the money for an new EGR cooler and oil cooler.
I know my oil cooler is failing as my deltas are showing a 15-19 degree spread over my coolant temps.
View 14 Replies
I have a 2006 f250 6.0. the truck has 101k miles and to this point I have had zero issues. I am having trouble loosing power after running at highway speeds. Once I stop and begin to accelerate the truck looses power for a few seconds ,Belches smoke and begins to operate normally. I had an egr code, so I replaced egr and the problem persist. It is intermittent and does not happen if I stay under 50 mph.
View 12 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 Replies
