Ford 6.0L Power Stroke Diesel :: 2006 F250 - CEL Is Always On / Error Code P1102
Jun 26, 2017
6.0 diesel 83,000 miles. My CEL is always on and my Edge gauge says it's lower than expected Mass air flow. I've changed the filter, cleaned the MAF with special cleaner and then replaced with new. I've replaced the EGR valve.
If I clear the codes and run it I don't get a CEL until I turn it off. But the next time I start it, there it is again. My Edge reads 0.0-0.3 MAF while running but what that means. One end of my cleaner box is slightly warped but I can't feel any noticeable leakage.
Everything runs fine but I would like to regain the ability to have that idiot light available to tell me if I have a new problem.
View 8 Replies
Advertisement
So when I first bought my truck the ABS light was on. Pretty sure that code is P0107. The other code I'm getting is P1102. I started getting that after I bought this SCT X3 from a guy. It has Spartan tunes. So when I tune my truck my check engine light doesn't come on, but whenever I shut it off and turn it back on the check engine light comes on and I get that P1102 code. Why? How can I fix it all
View 4 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
I got a 2006 F250 6.0 that won't start. It turns over perfectly. What I've done so far was change oil and filter, along with fuel filters. All fuses and relays are fine. I payed for the scan gauge 2 and monitored FICM SYNC, FICM voltage, ICP, AND IPR. Every thing checks out besides ICP. The ICP is reading under 400. So I unplugged the ICP. Still no start.
I decided to spray some starter fluid in the intake and turn her over. Boom starts right up and runs fine. I even drove her around for about 20 min. I get home and shut off the truck. wait a few minutes and nothing dead again. So ICP is low but the truck runs fine after some initial support from starter fluid. What I need to do next? I don't want to have to take it into the shop for something stupid I could do myself.
Also the code its throwing at me is P0231 Fuel Pump Secondary Circuit
View 4 Replies
I bought a 2011 F-450 with 205,000 Miles on it with a blow engine. Local shop installed a Ford NEW complete engine. Unfortunately we had Code P24A5 EGR Cooler Bypass Control Stuck after the swap. Truck drives fine just has CEL on. Goes to FORD and they test Vacuum from engine, on line, and on compents say all is good. Replace Vacuum switch and Control and neither fix it. Ford stumped and quits responding. So i go get my truck back since they wont respond and had it over 2 weeks.
I get it back and now it has Codes P04DA Closed Loop EGR AT Limit - Flow to high and P1102 Mass Air Flow Sensor in Range but Lower than expected. I also have a P21BO for the reductant level sensor "C" Circuit High.
Since picking it up from Ford, Truck has almost no throttle until oil temperature warms up. I clear codes, truck runs good after warming up and no CEL comes on. Drove it for over an hour. Next key cycle, and CEL is on with all the above codes. Could something be hooked up wrong? Where to start?
View 14 Replies
06 6.0 F250 throwing code P0677 #7 glow plug circuit module. I don't think one bad plug would cause a no start, however coupled with too much oil possibly? Swapped my oil about 500 miles ago, I put in 20qts accidentally, drained off about 3-4 qts eyeballed, truck fired up and ran fine no smoke nothing. Yesterday morning I was leaving work and moved my truck from parking space to behind the bay at my fire station, I turned the engine off.
Loaded up my gear and turned the engine to the aux position and someone was talking to me so inlet it sit for a while in the auxiliary position. Went to crank no start, turned the key off then back on and it fired. Fast forward after 7 different starts throughout the day, I'm at dinner with my son we go to leave engine will not start at all, rolls and rolls and rolls nothing. Towed her home and scratching my head. Over filled oil with a bad plug cause no start??
Egr delete, new oil cooler, cat and muffler delete, upgraded Y turbo pipe. Also have an SCII throwing codes p0677 and p0401 egr code....
View 14 Replies
My CEL is on and I pulled this code...I made the mistake of using a Hypertech programmer and the code came on soon after. I do have a stock code I saved from my SCT, would it fix it if I put it back in?
View 14 Replies
I just did a test drive with my 04 6 liter, I did the stealth egr delete. I had a P0400 error code any concern?
View 14 Replies
I've had the Ford Remote Access installed on my pickup for over a year now and it's worked great up until about a week ago when I changed cell phone providers from AT&T to Verizon. Now when trying to use the app I get the error code 00011000. I up-dated the app to reflect the new carrier but it still doesn't work. And yes, my subscription to the service is current. What I need to do to get this working again, with winter just around the corner I'd sure like to have this functional again. I figured I'd give the forum a shot before I resort going to the dealer.
View 14 Replies
I am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
View 2 Replies
Ok just bought a '04 F250 Diesel. Loving everything but can't get the keyless code to work. The keypad lights when I touch it and I have retrieved the 5 digit code from the "Bosch" box behind the radio. No deal. Locks don't react at all to the factoy code. Know what? I read that there is a list of all the possible codes. Where can I get that list?
View 14 Replies
Bought a 2011 F250 with P1635 code. It has 35x12.50 tires my Sct x4 tuner only goes up to 34 inch tires. Im new to the 6.7 diesel game previously had 6.0 and want to hear from yall what to do.
View 1 Replies
I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 Replies
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
I have an 06 F-250 with 122,000 miles. When driving empty at 70-75 mph the coolant temp runs 194-200 and the oil temp 5 to 10 degrees higher at the most. When I pull my travel trailer the coolant temperature will start to steadily climb then abruptly drop down under 200. I have seen the coolant temperature pass the oil temperature when this happens.
The last time I pulled the trailer I was driving at 60 mph and the coolant temperature climbed to 220 then dropped to 196. A few miles later it climbed to 230 then dropped to 200. While the temperature was climbing I slowed to about 45 mph. As it was dropping I accelerated and the temperature continued to drop.
I have flushed the cooling system, replaced the thermostat and cap with no improvement.
The pickup has an SCT tuner set to street 1 and I was told by the previous owner that the egr was deleted, but the stock egr cooler is in place. It is possible that a plug was put in. I pulled the egr valve and the carbon coating on it is gooey like it has been wet.
View 12 Replies
My 2006 F-250 6.0PSD has a new hitch. Tonight it would not start once hot. It cranked and cranked but no start. My scanner showed ICP readings of 366PSI during cranking. Far below the 500PSI needed before the computer will fire the injectors.
So is this the STC fitting at the HPOP that is failing? If so how long will she start cold and drive normal before she leaves me stranded? I have the fittings and new dummy plugs and stand pipes as well. I was waiting to to do this work until I had the money for an new EGR cooler and oil cooler.
I know my oil cooler is failing as my deltas are showing a 15-19 degree spread over my coolant temps.
View 14 Replies
I have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 Replies
I just bought a 2016 F250 with the diesel and thought I'd share an early ownership experience. At about the 1300 mile mark the check engine light came on and other than the remote start not working the truck continued to run great. I pulled a P0170 code, Fuel Trim Bank 1. And since the truck was still running fine, I considered clearing the code and see if it would come back. But since it's under warranty I decided to bring it to the dealer. They checked it out and diagnosed a bad Fuel Rail Pressure (FRP) sensor. They swapped it out and it seems to be good to go (no more light). While I was in there I asked them to turn on the DPF percentage full screen which they did.
View 3 Replies
I have a 2006 f250 6.0. the truck has 101k miles and to this point I have had zero issues. I am having trouble loosing power after running at highway speeds. Once I stop and begin to accelerate the truck looses power for a few seconds ,Belches smoke and begins to operate normally. I had an egr code, so I replaced egr and the problem persist. It is intermittent and does not happen if I stay under 50 mph.
View 12 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
