Ford 6.0L Power Stroke Diesel :: 2006 F250 - Alternator Rebuild - Charge Light On Intermittently?
Aug 8, 2015
My 2006 F250 has a single alternator and recently the charge light is on intermittently and I have watched output voltage fluctuate between 12.4 to 13.5 ... sometime a .3 volt bounce one way or another for no noticeable reason.
So rather than buy a new alternator, I would like to replace the voltage regulator and put in some new brushes.
What are part numbers that I need to pick up?
View 6 Replies
Advertisement
2006 f250 egr delete banks intercooler / cac tubes. Afe intake ... Sinister egr delete plate..... Truck smokes when sitting at a lite upon take off. Removed down pipe found slight amount of oil. Removed turbo put a kit in it and it is worse now. The turbo was in bad shape. The thrust bushing was pretty ate up and it had a lot of shaft play. I cant believe it wasn't hitting the housings. My thought was maybe the housing is bad. If the orings fail on the vgt solenoid what happens ? The vgt is working cause i can throttle it with the auto ingenuity...
View 14 Replies
I am having a charging system issue. The alternator is making barley over 12 volts. With KOEO the battery light on the instrument cluster does not come on. I have already replaced both batteries and the alternator -before i noticed the battery light is not coming on.
View 2 Replies
I have a 2006 Ford F250 Superduty 4x4 6.0L Diesel with an alternator/battery problem. We have charged the batteries (had them tested at auto zone), and replaced the alternator and still cannot get the batteries to keep a charge. I'm not talking a slow drain, with the ignition switch on for less than a minute it drains about 4 amps and the truck dies. We also noticed a trouble code "TBC fault" and discovered that was to do with the trailer brakes. Disconnected the trailer brake system (have been noticing a "check trailer" warning occasionally recently). What could be causing such a massive drain on the batteries?
View 3 Replies
Alternator locked up in a parking lot. Replaced it and had to replace pigtail due to a loose wire in the harness. Now battery light comes on intermittently. New alternator is doing fine producing anywhere from 13.9v to. 14.4v. No output voltage correlation to battery light at all. The belt is still in great shape so I don't suspect slipping. Fortunately I caught the old one locking up almost immediately and had recently replaced the belt. Output voltage looks great. Are there any fuses for alternator?
Only thing I can think of that I did...when splicing in the pigtail that connects to the alternator, I briefly grounded whatever wire in the pigtail is hot. Was just a split second, but enough to see a spark and maybe enough to blow a fuse? I've seen people reference an "under hood" fuse box, but I don't seem to have one. My truck is a 2002 CC with just over 100k on the clock.
View 3 Replies
OK...I ask that you bear with me while I explain my question/issue.
I bought a used 2006 F350 Super Duty diesel last October (Oct 2015) and it has about 124,500 miles on it now. Last week, the power cut out as I was driving home from running an errand. Jumped it and got it back to the house. Suspected the alternator as both batteries tested low (according to AutoZone). Purchased the 110amp alternator and after a few days...I was able to get the alternator installed. AutoZone charged the batteries back up.
Today, I was able to start the truck and drive it around the block in order to make sure everyone was okay - before I took it out on the streets. Got back to the driveway....ABS light comes on, radio shuts off, odometer light goes off, etc. I shut the engine off and let it sit for a minute. Try to start it back up...and nothing happens. Ended up disconnecting both batteries while I ponder the root cause of the issue.
Is it possible the 110amp alternator is not strong enough to handle the power requirements (and that's why the dashboard lights went out)? To the best of my knowledge, there's only 1 alternator. The only "extra" that's installed is the tow/haul package (which I haven't used yet). According to the Ford Parts web site - after I enter the VIN for my truck - the results show a 110amp alternator (heavy duty alternator).
Would exchanging the 110amp for the 140amp be the most logical place to start? Or is there something I missed as a replaced the alternator?
View 14 Replies
I have an 06 f250 and my fog light lens are in bad shape. Can I just replace the lenses or do I need to purchase a whole new light?
View 3 Replies
Idiot light was on for battery charging issues. Sanded all ground connections. Soldered battery cable connections. Scan gauge showed sporadic inadequate charging. Installed new alternator. Scan gauge showed sporadic inadequate charging. Installed new interstate batteries. Brought old alternator to be rebuilt, rebuilder said it was strong as could be, needed no work, high output alternator. Reinstalled old high output alternator. Scan gauge now shows charge output of 13.9 V to 14.1 V
Idiot light still on, flickers like a loose connection, sometimes lights constantly.Occasionally speedometer fluctuates wildly, when fluctuating like this at idle, the truck will stall, so far it restarts...so far. When it has stalled the speedometer still fluctuates wildly for a few seconds truck will restart and seem fines but this will play out again next day or so. Occasionally ABS light comes on, occasionally water in fuel light comes on and they go away after abit, some times after a restart, not always though
Thought it might be cam positon sensor however not certain with the instrument lights also acting as they do. Have had one cam position sensor open circuit code once, about to trip out west to Monatana & Colorado and back home to Ma in a couple of weeks, hoping not to be stranded somewhere in between those places!
View 14 Replies
I have a 2006 f250 with 120k. I am having trouble getting the water in fuel light off. I drainned the water out and replaced both filters and the fuel water sensor. The check engine light is now on and the water in fuel light is as well. I'm stumped and can't figure out what to do next. Will the check engine light come on as well with the water in fuel light or is it two different problems?
View 2 Replies
I just wanted to share with you all a cautionary tale about belt tensioners and idler pulleys. I am now a firm believer in installing the aforementioned items when you replace your drive belt. 15000 miles ago I replaced the drive belt and didn't heed the warning of some here on the forum.
For the last month or two I have noticed what sounded like road noise which I dismissed because I had just had new tires installed that had a more aggressive tread pattern than my previous tires, I also noted that the ECT had been a bit higher than normal, like running in the high 190's to low 200's on average.
Well while driving today I get the alternator warning light and lose power steering and soon after the brakes got stiff, this was followed by ever increasing ECT which got to 242* before I could get it off the road and shut down. It is too early to tell if the noises and the ECT temp rise were the result of this tensioner going out...
For what its worth the only tools required were a 10MM end wrench and a bit of skin to get the job done.
View 5 Replies
I have a 06 F250 6.0 My battery light has been coming on. Doesn't stay on but I'm planning a trip back east and don't want any issues to occur. I was thinking maybe the batteries. So I stopped at the local Oreilly's Auto store and had them tested. Told the guy what it was doing and he said it sounded like the alternator. He tested it and said it was going bad. He also tested the batteries and said they were good. So I went looking for a replacement alternator and they have different amp sizes. So I'm not sure on what size the original one is and if the replacement should be a bigger size amp wise.
View 11 Replies
Ok, so I have a 2004 F250, with 6.0L. when driving at a steady speed (doesn't matter what speed), the engine will run rough when coming to an idle, and stay running rough until I shut it off and let it sit for a bit.
After I cycle the key a few times it will fire up and run fine, so I came to the conclusion that air is getting in the fuel system. I then took the filter cap off that is located in the engine bay and cycled the key, which produced a lot of bubbles, which I am assuming shouldn't happen.
I guess my question is, should I have air bubbles in the filter bowl, when cycling the ignition?
View 1 Replies
We've got a 2012 F550 6.7 with 138k. It recently got a battery light. The batteries are right around 12 volts with the truck running or off. I also tested the output on the alternator and its not charging. I put a new alternator in it and still no charge. All the connections are tight and clean. The batteries load test ok. Where to look next?
View 4 Replies
So I have been having this little issue for a few weeks now. I will be driving along and out of nowhere my batt light will come on and my gauge cluster,radio and windows stop working and the ficim volts jump to 15.5-16.5. This is an intermittent issue. Yesterday I put my multi meter on the alternator and I am reading 13.5 or so this number was done at idle and the batt light was NOT on .
View 14 Replies
My ABS light keeps coming on randomly. Sometimes it's on for a full day sometimes a few seconds. It's pretty weird because it doesn't throw a code or anything. Where to go from here.
View 10 Replies
Had to do the icp sensor originally. went in from the top and discovered my oil cooler was failing too. so i did that. with weather (too tall to fit in the garage) and life getting in the way it's taking me 2 months a little here n there to actually get it done so she's sat for a while. yesterday was moment of truth to get it started again. the batts were old before i started working on it. so i replaced those yesterday.
I've tried and tried to get it to start and it won't turn over. it did for one tenth of a second try. nothing since. I saw that my shifter wasn't exactly in park so i wiggled it and tried to crank it again and now it won't even crank. I have a feeling somehow the transmission isn't reading in park or neutral so it's refusing to crank. I really don't want to tow it.
View 13 Replies
I have a 2006 F-250 4x4 with no cat, and no egr but the valve is still connected. It has about 146,000 miles. Just recently when warm, it has a slight miss every once and a while when stopped and in gear. Just a slight drop in RPM then recovery. Its mainly used on the highway and 99% of the time I set the cruise and its smooth as silk. Every once and a while I feel it stumble once or twice, recover and it is fine for the next 80 miles with no issue. It started as once every few trips but now It seems to be happening at least once every other. I use Motorcraft filters (maybe 6K on the fuel filters) and rotella oil. My scangaugeII shows no codes and no Injector pressure issue (1200-1400 at 75 mph depending on grade) and the FICM voltage stays between 48.5v and 49.0V. What should I check?
View 2 Replies
Running down the road today and the battery light came on. Went on and off intermittently as I drive home and the tuner showed 11.5v. Got home, shut it off (didn't mean to) and restarted it. Tested voltage at the batteries and was over 14. Need to take it for a drive and see if it repeats.
View 14 Replies
Started having some crank no starts intermittently. Scanned and found codes for cam sensor. so I was in a pinch and a hurry on a sunday so I picked up a BWD brand cam sensor from parts store and installed. I have not seen this issue since but started noticing other thing going on. I noticed a few weeks ago my truck was starting a little strange. as it would spin over before firing off, it didn't sound right. I couldn't pinpoint if it was due to slightly low compression on one cylinder or one cylinder had a little fuel or oil in it and that one cylinder was actually firing while cranking over.
I also was noticing a little longer crank times than normal. didn't matter if engine was cold or hot. sometimes would fire up quick and sometimes it took a few seconds. most of the time I couldn't catch it on my scanegauge if the ICP was low due to the lag on the scangauge.
Well one day on my way home from work (50 miles one way) I stopped about half way to fuel up. after filling up and attempted to restart the truck it really acted like it didn't want to start but did after cranking for about at least 10 seconds and started rough. and of corse my scangauge decied to hate me this day because it would show any data until I unplugged it and plugged it back in. so started home. felt like it had a very very light miss on the way home. when I slowed down to turn onto my road the truck died. took forever to get it to start back up. this time the scangauge was reading and I could see ICP was between 300-400 and IPR was 85%. so low pressure and not reaching the 600 needed to fire. once it started I limped it home. scaned it with my Auto Enginuity and it didn't show any codes.
So that much I can see I have a leak on the HPO system. but I done a lot of work to the truck about 2-3 years ago. roughly 80k-100k miles since the work. what I done included...
OEM oil cooler
OEM (updated)dummy plugs, standpipes & STC fitting
OEM head gaskets and ARP studs
BPD EGR cooler (I should have deleted)
ALL other engine gaskets(Bed plate, oilpan, front&rear cover, ect.)
OEM glow plugs and harness
OEM blue spring upgrade
Cleaned turbo veins
2 OEM REMAN injectors. (cant remember which two) had contribution codes one on each side.
This is all I can remember right now. Now have yall seen the updated dummy plugs and standpipes leak? I have not pulled valve covers to air test the HPO system yet.(don't have my air compressor at my new house yet). Here is what I have done so far:
Fully charged batteries.
I did do a bubble test. pulled upper fuel filter cover off and removed filter topped the bowl off and turned engine over using the wire by the passenger side battery. some bubbles but not a bubble bath.
Checked fuel pressure (not running) its 60psi. did not start truck because I need a different fitting so I can run the truck and check pressure while running.
while doing the bubble test I could hear that one cylinder is low on compression. but I do not have any misfire or contribution codes.
when I ran contribution test on AE its not showing any particular cylinder lower than the rest. but the line is not very solid at all.
Here is what I plan to do.
Compression test on each cylinder.
Looking at the Harbor freight kit. Looks like it has fittings for glow plug and injector holes.
If I can do compression test on both glow plug and injector holes this should show weather my injector orings are the cause of the low compression.
Then I have to airtest the HPO system and find the leak.
Am I on the right track? what else should I check? Guess I should add that the truck currently has 297K miles.
View 9 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
If I had to charge the batteries, Do you charge only the primary battery or do you charge both?
View 4 Replies
