just overhauled my 6.0. run great for about 3 days now runs really rough when cold. new heads injectors rings pistons ficm fuel pump icp sensor ipr valve fuel pressure is good. Engine rolls smoothly when cold also.
View 14 RepliesTruck is bucking and missing every 10 seconds or so and will stall when taking off in drive sometimes but fires right back up? I got a lot of codes in the torque pro app but some are in grey. Not sure what that means. EGR has been deleted so that's why I got those codes. I was cleaning the back of the truck the other day and found a can of quick start . Guess that might be why i got codes for glow plugs also. I'm gonna post up pic of my codes and numbers of truck running at idle in drive. So far I see I got a code for cylinder 6 contribution? It's in grey tho whatever that means.
View 8 Replies2006 F350 6.0 ... I am piling up parts for a bulletproof party later this summer. It has gotten grumpy ahead of schedule. I will hook up the AE tomorrow for consultation.
In the meantime. Running rough at 50. Seems to accelerate from a stop semi ok. Sitting at idle, holding rpm at 1750 I hear kind of a thump under the hood and the rpm drops 300, then slowly finds it way back to 1750 and it repeats itself.
This thump has not been noticed in the past. Could this be the VGT not working as expected?
I have 1 bad injector well it's missing when it's cold and two others that are "weak" I'm wondering what kind of job it would be to do by myself?
View 14 RepliesI have been having a problem for a while now where my truck will miss/buck at WOT. This only happens at higher RPM's. From a standing start 0-60 it is fine. However when I downshift full throttle from about 50 MPH it initially goes, but then it will miss/buck consistently until I back off the throttle.
I have so far replaced the CPS, re torqued injectors, checked valve cover harnesses and fuel pressure stays in between 64-58 full throttle. No codes show up.
My truck runs great except as I described above. I would think an injector or two are bad, but the truck runs and idles great. My initial guess was that it was a fuel pressure issue, but fuel pressure holds strong. Could it be air in the fuel?
My truck has been having this issue pretty much since I have had it, but it seems to be getting worse, or so I think.
When the truck is cold, it does not want to move very well. Like it's missing, and it does this until it gets warmer. Also, I have puffs of blue smoke come out the tailpipe when this occurs with it cold.
Injectors? Injector o-rings? Stiction?
FICM volts are good at 46.5v-48v when cranking.
I have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
I've got an issue with my truck, I was towing home my camper this weekend and my engine started missing out and vibrating very bad, then it overheated... pulled over and check codes, p0263, p0299, p0300, p0301. Oil all over engine, tons of blow by, definitely a dead miss on cylinder 1. Smokes bad out of exhaust, zero power, and blows cap off of oil filler when loose, tons of smoke and oil from ccv.
My question is, could it be in the valve train? Or is it going to lie in the piston/rings? Blown head gasket? It did overheat, but didn't puke out of bottle, turbo timer kept it running for a bit after I shut it down roadside, egts were definitely high. Also the egr is deleted, have a predator programmer with custom tune for she delete.
I Have A 2013 F250 I Have A H&S On It. I Have It Delete. And The Cel Comes On In The Morning, Ill Get The Code In The Morning. But It Has Something To Do With Coolant Temp Sensor. It Also Does Like A Bucking/Power Surge. Boost Goes From 0-10-15 ,When you Hold Pedal Steady. Do I Need To Update My H&S Or What?
View 14 RepliesWe are on vacation pulling the 5th wheel. On the last of the three days driving the transmission starting doing something I have never seen. When running about 60mph and starting up a grade, when I push the pedal and it should shift from OD down, it bucks really bad. It only does it under those conditions and only when towing. It does it when the tow/haul is on and tow haul is off. Also, in the afternoons on the last two da,ys the A/C has started to turn off. The fan still runs but the cooling cycles off. After a while it comes back and is ice cold but then cycles off again. It only seems to do this when the engine fan is running to cool off the engine under load. I have it scheduled at the local dealer for a transmission service and A/C check....
View 12 RepliesWhen I am on the highway, my 2005 Excursion (6.0) will hesitate/sputter/buck intermittently, usually between 70-80mph/ 1800-2200 RPM, but especially triggered by hills and inclines. Each sputtering episode usually lasts about 5-10 seconds and then will go away for minutes at a time. Does not sputter upon take off or initial acceleration. There is no smoke of any kind. Just got it out of the shop where the mechanic replaced ALL 8 injectors and the fuel pump, as well as flushed the fuel lines, and new fuel filters, and oil change (2 injectors were bad, but there was metal in the fuel filters, so to be safe I replaced all of them - ALL OEM PARTS for everything, including filters).
The week before, I had the IPR valve replaced. Also, recently had the back pressure sensor replaced and the EGR was deleted - and turbo cleaned when the EGR was deleted last month. I also tried unplugging the ICP sensor to make sure that wasn't the issue. Dropped $6k into this thing in the past month and about to lose my mind (and wallet). All research points to either clogged EGR or bad fuel injectors, but both have been addressed, so I am not sure where to look next. No current codes showing up. No signs of leaking oil.
Have just about 1,600 miles on tuck born on 12/14/11. Love it, but.. When going slow in subdivision I am getting some hesitation/bucking when going in the upper 20s/lower 30s. When I feel it I look down and I am usually in 3rd. Is this the transmissible thing? When it happened Sunday it felt like it was going to die. If I start off with a quicker start (to get to highway speed) it shifts fine. It just started the last few weekends......
View 14 RepliesTruck is running bad when first cranked in the morning, is bucking and running rough until warmed up, think the oil needs to be changed and which additive is better the archoil or Rev x?
View 14 RepliesI have a 2006 F350 6.0 diesel with 110K miles. it takes me about 10 tries to get the engine to start. When it finally starts there is a lot of smoke and engine runs really bad. This isn't the case if I have the engine warmer plugged in. After warm up the engine runs pretty good.
My engine light comes on sometimes and will go out other times. I have tried sever attempts at adding injector cleaner with no results. Am weary about taking it to Ford for an analysis. Where to start with repairs? I did take it to Orielly auto and had the engine checked on their scanner. Approximately two pages of possible repairs come up.
Since our weather has returned to the cold side......my truck has started bucking and hesitating at 45 mph with EOT @ 130 and ECT @ 140. I can gas on it and it will clear up/let off and it would start up again once it gets below 50 mph. Once the deltas reach 150+ it clears up completely. Its never done this until this week. FICM volts are steady @ 48V. What is causing this or what to look for?
View 2 RepliesI have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
2006 F450 6.0 that I've owned since new. It has had 2 injectors replaced previously, EGR cooler with BPD, and a few other problem parts. As it is getting older, I have recently noticed it runs like absolute dog crap when it is cold. It can't even reasonably accelerate onto the hwy when cold. Once it is up to operating temp, it runs better. It still does not pull like it did when it was new and under 50k miles...but it is at least driveable once warm. I need to do some heavy trailer towing soon and need to get this thing back to accelerating good. What should I be looking at first for the horrible running condition when cold?
View 14 RepliesSo, I was on my way back home driving through the middle of nowhere Utah late at night, when I had an injector tip crack. I was able to identify which one and unplug it so I could get to Grand Junction, CO (about 350 miles away) where I have family. After a power nap I started calling parts stores and found an injector from Advanced Auto Parts (I couldn't find a motorcraft reman, but I was restricted for time). Installed it and all seemed good so I hit the road again. However, nothing changed. It still had the bad miss (rough idle, jerking/bucking when the torque converter locks up) just like when I had the injector unplugged.
The truck is an early 2004 6.0. It's the number 4 injector. I finally got home and hooked up my AE scanner to discover a #4 injector circuit low P0270 code and circuit contribution/balance fault P0272. It's definitely missing because disabling it has no effect. This could be a loose connector at the injector or FICM, because I can't afford another injector right now.
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 RepliesI have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
To start off. I have a 2004 F350 with the 6.0 in it which just had a top end rebuild done on it due to the head gasket blowing on it. During the rebuild the EGR cooler was also deleted, ARP head studs, Heads were milled down to make them flat (shop said they had to take 9 thousands off to do so), new up pipes installed, new back pressure sensor installed due to the plug head snapping off, new glow plugs, new glow plug rail harness, oil rail rebuilt due to bad o-rings on the ball tubes, injectors were installed with all new seals and had polished the spool valves hoping to avoid stiction (however its spelled can never remember), and lastly the EGR was deleted electronically with tuner. Also had to get 2 new batteries as they were stone dead and would not take a charge. And had to get a new alternator due to low output. Not sure if the alternator killed the batteries or the batteries killed the alternator either way it needed replaced to.. Unfortunately after i got that fixed i had to get a new starter as it died 3 days later.
Ever since its gone back together Ive had a consistent intermittent miss with the truck. Ive searched every article i can find but seems most complain about misses when cold. Mine is the exact opposite as it only does it once the engines up to normal operating temp. It accelerates hard and fast like it has no issues. While its cold it doesnt miss at all. Once its warmed up sometimes while cruising it will feel like its missing on every cylinder or better description would be as if your driving on a cobble stone road.. If you mash the pedal for a couple seconds till it kicks down and raises the rpms it stops.. Its most prevalent at idle though.. You can literally hear the difference in the engine when it starts missing. Truck will shake as if its got a large lopey cam. Odd part while sitting at idle it will cycle back and forth between running smooth and missing. But same with at cruise as soon as you get on the throttle it goes away. If its doing it while sitting idle at a light, it will take a couple seconds once your on the throttle for it to smooths out. But always does.
Ive tested the Ficm hot and cold, KOEoff and KOEOn.. getting a steady 48v from the main board.. Scan gauge says the Logic boards reading steady 13v... Also from the scan gauge it says my ICP pressure is in the 640 range at idle (full throttle highest ive seen is 3600psi so dont think its a pressure leak) and volts bounce between .80-.90.. but oddly once it starts missing the ICP pressure jumps up 20 psi.. IPR at idle reads 23.5-25.5.. at cruise its up around 45ish.. fuel pressures said to 70 psi.. which its usually around that most times, cruising itll be around 66psi. I had 3 injectors replaced not this past spring but the year before (ironically same symptoms).. Injectors 5,7,8 were replaced then.. ICP sensor was also replaced at the same time as it split and shorted out the connector which was the initial reason i took it in that time since it was dumping the oil on the ground.
I dont have any way to perform a cylinder contribution test and after spending 6K on a rebuild I really cant afford to take it in to have someone else do it. A local guy was able to scan the truck for me but he couldn't do the contribution test either but was able to buzz test them. Everything passed there but we also found some hidden fault codes my code readers did not find. The ones we found hidden said that injectors 2, 4, and 7(again??) are reading low contribution. Of what I've read 2 & 4 sit on either side of 7 in the firing order so have wondered if they're not pulling down 7's results.
I really cant afford to replace the injectors till near the end of next month. Is there anything else I can look at that might actually possibly be causing false readings or intermittent misses only when warm.