Need to know if you can mount a 04+ turbo on a 03 engine without changing the intake with the cross in the back ? Or does the intake have to be changed. If the intake does need to be changed will the egr need to be change as well ?
View 4 RepliesWhat's the purpose of the pedestal sensor
View 1 RepliesAre we supposed to put anti sieze on the turbo to pedestal bolts. They were really hard to break loose when I pulled it Cheater bar tight. 18 ft. lbs sound right ?
View 2 RepliesAny success story on converting 2003 or 2004 f350 with leaf spring front end to the 2005-2007 f350 coil front end is it possible?
View 8 RepliesHaving an issue with my 05 f350. Seems when I chomp on the the throttle I get tons of boost 30 lbs plus with no power. Seems most prevalent when starting on a hill , or hard on the throttle off the line . Also getting turbo "bark " when backing off throttle. It's less prevalent when feathering the throttle and usually more noticeable 1/2 throttle or more. I'm thinking could be the Vgt actuator or clogged/ dirty ebp sensor?
View 10 RepliesThe 2004 and 2005 turbo is interchangeable and can you replace the bearing in it.
View 8 Replies2005 F250 SD, Crew Cab, Diesel 6.0L...
Hauling my jeep (close to 16,000 pounds all in F250+trailer+jeep) on a highway going a little over 70mph up a hill when I seemed to have lost some power and the check engine light came on. The turbo PSI was well over 20PSI (according to the gauge in the dash). I have a Scan Boss but I have not been monitoring turbo boost PSI.
I was only 10 miles from the final destination so I continued without stopping. It seemed that the turbo was limited for the rest of the trip. Later in the evening, no more check engine light but I haven't really driven the truck since then.
What do you think the problem was? What should the course of action be?
My 1999 F-350 7.3 is leaking from the turbo pedestool o-rings, from what my mechanic tells me. I would like to do this myself as it does not seem overly hard. This is my first diesel truck and am not quit sure how to do it. Looking for instructions or pointers on the process? I am a decent mechanic, but just have no clue on diesel engines and hoping to learn.
View 7 Replies2005 f350 6.0 all stock except egr delete. My turbo is spooling up and down constantly. I can actually watch my VGT duty cycle fluctuate while sitting at an idle too. I've cleared the codes and p0299 always shows up first, but then I'll get p0069 BARO/MAP, and a p0470 exhaust pressure sensor eventually. Sometimes it takes an hour of driving before those show up. I can watch all these values on my torque pro, and nothing seems out of the ordinary other than the turbo opening and closing at will. What can cause this? I hate to just start throwing sensors at it.
View 11 Replies2005 f350 188000 on the clock had a bearing get loose in the turbo . Installed a new power-max but if the bearings are oil fed should i also change it? There are no signs of metal in the oil or the old turbo . The oil has 600 miles on it with archoil.
View 1 RepliesI've been having issue with my truck lacking boost over the past month or so. The psi levels are normal in the morning when I start it up cold, the problem almost always occurs at start-up when the truck is somewhat warm and has been sitting for an hour or more after use. I've had boost levels at idle from -0.14psi to -0.56psi and as low as -1.2psi when driving as the problem is occurring, but it eventually kicks on and goes to normal levels after several minutes of driving. After originally taking the truck to a local diesel mechanic I was told it had EGR codes and they recommended installing an SCT tuner and cleaning the EGR valve to solve the problem. I had them install an SCT 5015 tuner and clean the valve but I've still been having the problems with boost.
View 2 RepliesDid the swap and all works good except the boost is often at 3psI then sometimes it works good. Used the 03 harness. So did I need to change a wire or sensor or use 03 pcm?? I was told maf sensor might cause issues but no codes for it.
View 10 RepliesI have a 2003 Excursion with a 7.3 and 240,000 miles. I have oil leaking around the transmission and the local diesel shop found the pedestal leaking. I installed a new pedestal from Rotomaster Part # A1382205N. It came with new O-rings and turbo bolts. I ran the truck and it began leaking again. Thinking I had pinched an O-ring I pulled it apart again but found nothing. I cleaned and inspected everything and reinstalled. Its still leaking. I used a straight edge to ensure the sealing surfaces were straight.
View 14 RepliesI have a 2005 F250 with 186K miles. I do minor work on my vehicles but have little experience working on my diesel. I was accelerating when I heard a pop and a hiss similar to disconnecting an air hose from an air compressor. Total loss of turbo power. No turbo reading on the turbo gauge on dash. No loss of oil. No smoke. Oil and coolant look fine. Took off turbo and everything appeared to operate like it should (according to YouTube videos). Inspected lines and rubber boots.
Rubber has some cracks but not certain if they are holes. How small/large of a hole would cause total loss? Was originally scared to take it to a shop knowing they could name their price. Not opposed to taking it somewhere now knowing the turbo works but obviously would rather save the money. Any tips on troubleshooting? I'm not opposed to proactively replacing parts/sensors as the truck has given me 186k and I plan to keep it as long as possible.
I am replacing the turbo on my 2005 f350 6.0. I have the passenger side mounting bolt and the rear mounting bolt out, but cannot get the driver side bolt to budge. I have sprayed it with WD40 and PB Blaster and tried a breaker bar. No luck breaking it loose. I am afraid I might round off the head even though I am using a 6 point socket.
View 12 RepliesFor a month or two now my truck has been making a squeal and the turbo has been sticking after hard acceleration. The sticking was a woebegone unison ring and I was hoping the squeal would be resolved when I cleaned the turbo but it didn't, in fact, it got worse.
It used to be occasionally and go away after warming up, but now it's more constant than not. It goes away when the VGT does its idle cycle and once you get up to speed.
Here's the sound - YouTube.....
This is is a truck I hardly know anything about. My wife bought it while I was deployed for herself and when it comes to vehicles she's an idiot. No, really she told me she bought it because at horse shows everyone else has one.
I noticed an oil leak and had a reputable shop look at it. They told me it was coming from some seals on the turbo. Long story short there is a brand new turbo on there, stock replacement. Now it seems very under powered and shifts hard. Pressing down anything more than 25% throttle will cause hard shifting or no shifting at all. It'll stay in second until I ease off the throttle.
I tried searching a few terms but I'm not sure what to look for. I don't know if someone has messed with the tuning. Broken clamp on the turbo. Replaced and everything is back to normal...
I'm curious to know if it is theoretically possible to (some-day) swap out the V8 gasoline engine w. a VW DIESEL/Turbo power plant. Are any of the VW Diesel engines directly compatible w. the V8 transmission, mounting brackets, electronics, etc. etc. The Glow Plug indicator in the dash, though not required for me, would be nice to have as a reminder.
View 9 RepliesHaving a turbo shaft that broke? My 03 F250 turbo shaft was just replaced by the dealer, actually the whole turbo. This is the 4th turbo. Truck has 48000 miles on it. 1st 3 turbo's had sticking unison ring & vanes but this one had a broken shaft. Mechanic said unison ring & vanes were fine.
View 4 RepliesI have an '03 powerstroke 6.0, 4 inch turbo back exhaust. truck had lost boost and would cut in and out if i got on pedal and now a little bit of oil is collecting at tip, could this be because of bad turbo seals? And could the turbo still be alright? Another thing, I'm losing coolant, and I have noticed when I took the EGR out and cleaned it, the valve itself was the powdery black carbon, the cooler was wet, and I know it's not supposed to be like that. I am not thinking head gaskets yet, cause if it had a blown head gasket, I wouldn't be able to drive it. It is currently sitting, and I'm just trying to fix it. Would I be able to fix the turbo seals myself?
View 4 RepliesSo I just purchased my first diesel a couple weeks ago (2003 f250 Lariat). I love it! However, I'm having concerns about my turbo whistle on it. At idle and while in higher RPMs is sounds ridiculously loud (even at 0 PSI in the boost). I've been doing my research on it and I know the 03's have the loudest sounding turbos because they have less vanes than the later models. I know without a video it's going to be hard to diagnose, but I am wondering if a loose boot would cause a turbo whining sound through the exhaust? I have yet to hear ANY other diesel in person that has a turbo whine as loud as mine.
View 14 Replies