Ford 6.0L Power Stroke Diesel :: 2005 - Transmission Temp Gauge Dropped / Tow Haul Began Flashing
Mar 6, 2016
Okay so I just peaked 100k and (of course) my 6.0 has an issue. I was driving along when suddenly my Transmission Temp gauge dropped to nothing, the tow haul began flashing and my check engine light came on. My transmission hard shifted and wouldn't shift up from 3rd. I let the truck sit for a few days, no leaking was observed and no blown lines. I added 4qts of tranny fluid and went to take it for a spin. The truck did fine for about 20 minutes and the same issue occurred. I parked it and checked the dip stick and it was full. What could the issue be.
View 5 Replies
Advertisement
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
View 10 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
So driving the other day and tow haul starts flashing. I come to a stop sign and goto take off and it barley takes off. It will barley roll if my foot is off the pedal sometimes wont even roll. Also won't shift into 6th. Once it gets rolling though say till about 25 it's fine. Just doesn't wanna take off? I scanned the trans but got no codes. And here are some pressures and stuff but I don't know what I'm looking for with the trans. This was all done in park.
View 14 Replies
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 Replies
My co-worker has an 06 F250 SC 4x4 and is getting a P0713 code. 2006 Ford F250 6.0L Diesel ... Tow/haul light comes on flashing at random times. Truck is reading a P0713 code which is the TFT Sensor Failure/Replacement
Ford dealership is telling me that I also have to pull the valve body and install the new upgraded wiring harness (3-3.5 hours labor) but a thread on this forum stated I just needed to replace the sensor in the tranny pan and reconnect the wire harness. Do I need to upgrade the wiring harness?
View 3 Replies
I am at work and dont have access to my manual. I was driving into work today and the outside temp gauge dropped from 40 to 39 then chimed and flashed as if to say "he it dropped below 40 outside" then it showed a little snowflake picture next to the temp. I have only had the car since summer-so why was it telling me it dropped to 39?
View 11 Replies
Well, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
View 5 Replies
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 Replies
I have an 05 Excursion and I drove and parked it, no problem. Came back out and the trouble began. I looked on this site (always do for the best guidance and info) and replaced the trans position sensor, put tunes back to stock. Since then, I have had intermittent issues with the truck only starting with the code reader plugged in, idle jump to 750 rpm, and the tow/haul light flash and won't shift into OD. It also seems at full stops it is not in the low gear. I am driving it to the "stealership" today to have the computer flashed. Additionally, the blinkers won't flash, they only illuminate. All this started at once. Where all the ground straps/wires are??
View 6 Replies
2005 Ford F250 4x4 XL 5.4L 5R110W WITH 177,600 MILES... Tow Haul light flashed after 78 miles (along with other codes) after purchased. I purchased it used. While driving transmission would stop pulling as if it went into neutral and slam back into gear, at same time Tow Haul light be flashing...
Code is P0760 shift solenoid #3, I read from the forums on the site one caused could be the ground wire. We installed a ground strap from battery to tranny
Still does the same.
I have a shift solenoid ordered if needed, knowing the location of #3 solenoid in the tranny is the key to not having to keep dropping the pan. I love this site and have been reading it for long time.
View 9 Replies
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies
So I recently bought a '04 F-250 early build with the 6.0 powerstroke. Truck drove fine for the first 1000 miles. Drove from Fort Hood back home for leave. Got home and truck sat for two days, started it up and it ran for 15 minutes, then shut off on me. Temp gauge read normal, but after it shut off, I turned the key off and back on and temp gauge was maxed out. And truck has to cool down before it will start again. Replaced the IPR Sensor to no luck. Not sure if I have an ICP sensor issue or what it could be.
View 11 Replies
I have a 2003 Excursion 6.0. I didn't post this in the 6.0 section because it may not be just a 6.0 issue. (See what I get) On cold starts, anything under 150 degree water temp reading on the SGII. I get a CHECK GAGE light on accompanied by the check engine light. No codes read on the SGII pending or stored. Just some of the time I get a water in fuel light too. This tends to go out fairly soon after driving. (Even after I just drain the fuel pump it still happens.) other issues that accompany the lights are as follows.
The trans temp does not give a reading to the dash. The oil temp does not give a reading the dash. Both show proper temp on the SGII. When in reverse the back up alarm beeps as if something is behind me. And the auto door locks will not activate after 10 mph. The tach also will not show a reading in the dash. SGII shows the numbers. Now the kicker, this ALL gets resolved the instant the water temp hits 150 degrees. The only lingering issue is the that the tach will surge or drop every now and then. The tow/haul light does not come on when this is going on. I've checked the battery terminals all are clean. Both batteries are brand new.
View 9 Replies
Driving my 2003 today seen the "check gages" light on and the trans temp gage pegged on hot. CRAP, tranny time! look at the edge evo and it reads trans temp as -60F ???. Plugged in the torque pro and it reads 8,240F. At that point I figure its PROBABLY not that hot. Let it sit for a while and back to normal. Watch trans temp on torque pro as I drive it and everything is fine till it gets to about 150, then it jumps to 60F, then 30F, the 8240F. The cooler lines and trans pan are both feel normal. Picked up a new temp sender on my way home.
View 5 Replies
I have a 2007 6.0 that this has happened to twice now. It's fine around town but I never hear the can come on. Friday when on the interstate my my temp gauge started to rise past normal operating temperature before fan came on. Is this normal? After the fan came on it stayed at normal temp for the rest of trip....
View 5 Replies
I had this issue a few years back, but the problem disappeared. You can read about it at this link. Now the problem is back.
[URL] ...
2005 F350 6.0
New International ICP (two weeks old)
New pigtail
Truck starts and runs fine. When it gets up to temp, usually about 20 minutes into my 40 minute commute, the ICP psi at idle will go to 875 psi, steady. I believe the pcm is defaulting to 875 at idle. I still get a ICV reading (changing with RPMs) when in this condition. After driving like this for about 10 more minutes, the wrench light comes on and I throw code 2286 High ICP.
I have found a couple places in the wiring harness under the turbo where wiring got hot and melted the wires. I removed the portion that was melted and soldered in new wiring. Problem remains.
Here are a couple snapshots of scanguage II, one at idle and one at koeo. I still think I have an intermittent open in my wiring harness.
View 14 Replies
Today was drive my x 2000 v10 limited 4x4 114k miles). It was 90 degrees Out and was driving in light traffic going 40 and noticed my temp gauge almost up to h then dropped fast. So shut the ac off and it continue to rise and drop fast I went few more miles to where I was going checked everything could see no problems it sat for about 30mins then left on my drive back home 36 miles and had ac on and no problems stayed where it normally is. I am thinking of just replacing the belt cause I never have. No weeping from water pump. Or any smell.
View 6 Replies
2005 F250 Superduty Crewcab 4x4 6.0L diesel/auto
Wife drove the truck before me and bunched the floor mat under the pedals. I didn't notice the mat issue when I drove the truck today. I accelerated fully after doing a left turn onto a busy highway. The motor spun up hard with the accelerator floored but because of the mats, the pedal stuck all the way down. I was approaching stopped traffic while under full acceleration and I shut the engine off and pulled over to the shoulder all while braking hard ( it was a hell of a ride!). I freed the pedal and restarted the engine.
Now, despite a bit less than 1/2 tank of fuel (I have the 38 gal tank), the dash readout was showing "Low Fuel", the gas gauge was below E and the engine was running like it was running out of fuel. I turned the engine off again and left it off for 1/2 hour before restarting it but the gauge and engine still behaved the same. As I drove to the nearest diesel station, the engine was not running "right". Of course the station I pulled into had 1 diesel pump and the pump was broken.
Because I thought I might actually be out of fuel, an understanding stranger took me to the store to buy some gas cans and then to another station to get 6 gallons of fuel. I got back to the truck and added the 6 gallons of fuel. When I turned the key on, the fuel gauge immediately came up to 1/2 tank. I then drove to that other station and added another 15 gallons of fuel to fill it. This confirmed that I had about 18 gallons of fuel in truck when the "Low fuel" warning occurred.
So, what the heck was going on with the fuel gauge? I am sure the "Low Fuel" warning is tied directly to the gauge but why was the gauge reading low? Is it possible that the "Key-off" while under full acceleration followed by hard braking had confused the ECU? I am just trying to figure out if I have a fuel sender problem or a confused computer that corrected itself. Until this incident, the fuel gauge has never been a problem but the wife messing up the mats has been an issue!
View 3 Replies
I'm looking to buy a used 2005-2007 6.0L and bought a ScanGauge to take with me when I look at the next truck I'll be considering. I dont have a truck now and I see that the ScanGauge derives power from OBD port of the truck. Is there any other way to set it up in advance?
View 9 Replies
I just got this f350 6.0l and I experienced an electrical problem with the trans gauge, started flicking a lil then go all the way up to over hit and check gauge light go on and my tow light starts blinking..
View 4 Replies
