Ford 6.0L Power Stroke Diesel :: 2005 - Suddenly Whistling At Idle?
Sep 11, 2016
I have an 05 Excursion that has a rebuilt stock turbo on it, installed before I bought the truck. I installed a 3.5" downpipe/4" after exhaust with no cat and no muffler about a year and a half ago. It seems like suddenly my truck is whistling a lot more than it used to at idle. I'm not unhappy about the whistle sound, just wondering if this is possible (i.e. turbo vanes sticking or something else) or if I'm imagining things.
View 5 Replies
Advertisement
So I just purchased my first diesel a couple weeks ago (2003 f250 Lariat). I love it! However, I'm having concerns about my turbo whistle on it. At idle and while in higher RPMs is sounds ridiculously loud (even at 0 PSI in the boost). I've been doing my research on it and I know the 03's have the loudest sounding turbos because they have less vanes than the later models. I know without a video it's going to be hard to diagnose, but I am wondering if a loose boot would cause a turbo whining sound through the exhaust? I have yet to hear ANY other diesel in person that has a turbo whine as loud as mine.
View 14 Replies
Well, after getting the bed back on my '05 F350, I have been driving it on the road for a few days, but now I have a new problem.
Every once in awhile I get lag off idle for about a second, then the turbo spools and everything is fine. Other times, I step on the accelerator a bit from a stop, and the truck acts like its going to die for a moment, a puff of black smoke, and then the turbo spools and all is back to normal. It a combination of these two problems happens about 3-5 times out of 50 stops a day.
I have a scanguage and everything looks normal and I never get any codes when I check.
View 14 Replies
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
View 9 Replies
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
View 5 Replies
My 2005 Excursion, at 198K miles has become more of a 'hangar queen' in that I only use it for big jobs. I've kept it for towing/hauling and making long highway runs with more than 4 people.
The truck, 99.8% of the time, runs super. It pulls like a locomotive and gets decent fuel economy (17 mpg running 75 mph empty). I've got the 'blue spring', EGR delete, ARP headstuds, 4" MBRP, Banks intercooler, and run my SCT tuner all the time on "8000 lb tow".
But...there is this weird intermittent problem. It appears to only happen when it is warmed up and driving around town. Sometimes, when I pull up to a light, with my foot on the brake, the engine will sort of go into a 'lumpy race idle' and you have to clamp down on the brake pedal to keep it from lurching into the guy in front of you. Other times, it just runs rough and idles 'lumpy'. It has only died maybe 2 times when acting up. Often, the symptoms disappear on their own and don't come back. If I turn off the engine and re-start (to keep from scaring people at the bank drive-through) it usually runs fine after restart.
I've got an EDGE CTS monitor so I've been trying to find out from that what is going on. I can't seem to catch the parameter that might tell me. My local 'indy' shop can't find any codes thrown. The truck had new alternator, batteries, and starter motor installed in January this year. These symptoms have been going on for several years. Recently, they seem to occur more often.
I've searched on this site a few times, but with no definite 'hit'. I'll admit that I'm a big out of the jargon. I keep thinking this is related to FICM, but everyone seems to say the FICM would manifest as a cold start problem. I do know the FICM sits right on top of the drivers side valve cover. It has got to get hot.
FICM?
Injectors?
How do I kill this one strange problem?
View 7 Replies
2005 6.0l - codes are P0261 Cylinder 1 injector circuit low. PO263 Cylinder 1 Contribution/balance and PO270 cylinder 4 circuit low. Ficm still reads 48 plus or minus .5. What is really puzzling is how changing the oil cooler and the EGR cooler would create these problems. Did I screw up the injector harness. Vehicle does not smoke either white or black. Low idle miss and at 55 it chugs once up to speed. Don't want to go Ford if I can avoid them. Whats going on.
View 7 Replies
My truck is a 2005 f350 6.0, all stock except for an egr delete and 4 inch cat back exhaust. I recently did an oil cooler replacement and egr delete, resealed all 8 injectors, and fixed some wire chaffing at the FICM. it's running great with the exception of idling. It seems like it's idling low but the gauge stays at 750. If I hit the high idle switch, it does fine. Red lights are stressful because it shakes and sounds like it's going to die but never does. I'm posting screenshots of my Torque pro.
I have a SC2 as well but I honestly like Torque better so that's what I use most. I know my ICP is low, but 8 don't know why. No oil in the connector, and no change when I unplug it. The ICP sensor may be a month old with 1000 miles on it. This was taken at a hot startup, sitting in park. When i say hot, I mean I had driven about 60 miles. This is sitting still in drive. ICP voltage finally climbs over 1.0 when i get going about 15mph at around 1250 rpm. The second pic the ICPV is actually higher than normal. It usually stays at .8 until I give it gas.
View 5 Replies
A while back my 05' f350 6.0 was having rough starts and an erratic idle. It died coming up to a stop sign it started back up after 2 cranks and then it did that same on the way home. The next day leaving work it wouldn't start. I knew i had a couple injectors on the way out so i decided it was time to replace all 8 upon tearing it down i noticed my oil cooler was leaking so i figured it was time to rebuild that and finally do the egr delete that i had been wanting to do. well i put it all back together and got a no start.
The dash gauge on my oil pressure is reading normal when i cranked it so i went and bought a scangauge2 to read the icp its hitting 1500psi when i crank it. The ipr% is reading good. But my ficm main power is at 26v with the key on then it drop to 14v while cranking and eventually down to about 9v. Its never at the 48v that its suppose to be at. The scan gauge is also showing that my ficm sync=0. Would the sync be showing 0 since the ficm is bad? My batteries are fully charged and i have both of them on the charger while I am cranking it.
View 4 Replies
The last few weeks, I have been hearing a whistling/whooshing noise on WOT when going to pass someone.
It is coming from the right side of the engine compartment between the turbo and firewall.
At least that is where it sounds like. I have no clue how to verify that driving it. What to check?
View 3 Replies
Rough idle I have had for little bit.Would stall out at idle or a stop, but fire right up? No one could figure it out with the stalling, but now its bad, started yesterday. Have white/blueish smoke sometimes, ( white smoke smells fuel) on restart after warmed when it dies, first time it took 25 mins to restart, now only takes 5 to 15 mins, when I step on it INCREDIBLE full power, fuel mileage gone to hell also since yesterday. Had full tank, now 1/2 tank.
No problems on cold start at all, no check light, 325,000 and never had this before.
Bad fuel?
ICP?
FICM?
Recent work, new turbo, ( turbo was original turbo installed when built) cooling line to waterpump, oil change, new fuel filters, front brakes and 2 new batteries.
View 5 Replies
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 Replies
I have a 2005 f350 6.0 power stroke. I had a crank no start when hot issue. I bought an obd scanner with the torque app. IPR was at 85%. ICP pressure was low. I got the IPR out and bought a new screen because it was clogged. Upon putting in I broke the injector female side plastic connection.I bought the injector connector piece and installed it. After putting everything back together it starts but runs very rough,low power. The IPR was fixed. ICP,ipr and ficm are at good levels now.
IPR=14.7%-30%
Fcim sync=1.0
Fcim voltage=48.5
ICP pressure (idle)650-850psi
My fault codes are:
P0672 (glowplug)
P0674 (glowplug)
P0678 (glowplug).
Why it would be running/idle rough?
View 14 Replies
I've got a 2011 F350 Lariat crew cab and when i get up to 75 mph with a cross wind, there is a whistling noise. it sounds like a turbulent whistle as if its blowing across the ribbed portion down by the wipers. I tried to get audio but for some reason my phone wont pick up the noise, but its extremely loud at times. Sometimes it will wake up the kids if they're napping in the back seat.
View 14 Replies
Well my problem went from bad to worse. My 05 started running rough at idle, then smoothed out a bit but started smoking on acceleration a little. At this point it felt like it had more power than ever before and even ran smoother running up to 3k RPM before shifting (manual transmission). But now it's smoking so bad, I can't really drive it. It's smoking white or gray at idle but blowing black smoke on acceleration. I had a cylinder 5 contribution code but with the amount of smoke it's hard to believe only one injector is a problem. I pulled the EGR valve and it doesn't look stuck open but I'm going to replace it anyway.
View 3 Replies
I have 2003 f250 6.0, had the turbo rebuilt and I put it back in, my turbo is whistling but I'm also getting a humming noise kinda sounds like a when u down shift at high rpm's idk what's going on, I try and power break as well to build up boost and the tires do not even spin...
View 4 Replies
After 2yrs and 1mo, my DC power 270XP amp died. I put the almost 10 yr old factory alt back on and everything is good again, except for the glaring fact that I have a dead alternator. It is a month beyond warranty (of course).
Truck has been running great. Oil cooler, EGR bulletproof cooler, STC done in Dec at Ford due to high deltas. I have a small stereo - one 12" sub woofer, otherwise nothing that really stresses the electrical system. I did the "big three" with 1/0 copper - cost a fortune, saw no difference - but that could have been an issue for the alt.
I left a message today with etch support but did not get a call back. I hope they make good on this - I waited almost 4 mo's to get this thing and it was supposed to outlast my truck.
View 14 Replies
Blows cold, so not a freon issue, but it will sometimes just suddenly stop blowing cold as if I punched the "A/C" button disengaging the compressor. Sometimes if I just wait a while it will come back on by itself, sometimes I have to stop and shut the truck clear off and take the key out, then start it back up and all is well again and it blows cold again.
High pressure switch failing???
BCM issue???
View 6 Replies
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?
View 14 Replies
Driving home from work last night my truck just died. I was under load, going up hill, and she just shut down. No power, completely dead.
She'll crank, but not start.
Ever hear of this?
View 14 Replies
I was out for a short drive this evening and got on it just a little bit to hear that wonderful 6.0 sound and all of a sudden coolant started spraying up on the windshield like I was spraying it from the windshield wipers! My first thought was oh crap I've got a blown head gasket and it puking from my degas bottle. I had a short drive to the house so I eased it on home. My ECT got to 226 with the fan roaring but not cooling it down, luckily it never got over 226. When I got home I opened the hood expecting to see where a bunch of coolant had puked from the degas but instead I saw this. What could cause the radiator to rupture like that? I did spend a good amount of time on my knees on top of the radiator while changing out my oil cooler the first time, then again when I installed my BPD oil cooler. Also I posted in another thread a few days ago about my ECT temps being a little higher than normal, reckon my radiator was clogged and that caused the higher temps and the rupture?
View 8 Replies
