Ford 6.0L Power Stroke Diesel :: 2005 - Smoking White Or Gray At Idle But Blowing Black Smoke On Acceleration
Jun 20, 2016
Well my problem went from bad to worse. My 05 started running rough at idle, then smoothed out a bit but started smoking on acceleration a little. At this point it felt like it had more power than ever before and even ran smoother running up to 3k RPM before shifting (manual transmission). But now it's smoking so bad, I can't really drive it. It's smoking white or gray at idle but blowing black smoke on acceleration. I had a cylinder 5 contribution code but with the amount of smoke it's hard to believe only one injector is a problem. I pulled the EGR valve and it doesn't look stuck open but I'm going to replace it anyway.
View 3 Replies
Advertisement
I have a 04 6.0l and all of a sudden it started dumping white/grey smoke at idle and when I drive it it goes to black then let off throttle and back to grey/white I had an up pipe leak at the y pipe I thought it might be an issue with that but I just got done fixing it and the problem still there so iam guessing it's either a sticky injector or the ficm but it starts up nice and does not knock around egr delete is don with all the goodies arp studs ect also the injectors have only 30k so it's hard to believe but iam just stumped haven't tested ficm yet and my tuner doesn't pick up any codes
View 14 Replies
I bought a 03 6.0 dually a couple months ago. Got a good price on it. I use it very little, around town sometimes and used to pull a 7000 lb camper sometimes. My issue is, the other day I took off with the camper. Drove for maybe 5 miles then stopped and waited for traffic. When I took off again it was blowing gray smoke when I was accelerating and had little power. I was going about 30 mph for about a mile at about 3000 rpm up a very gradual hill. I was in the tow setting. When I got to the top of the hill it seemed to recover. I pulled over and shut it off then took off again without any issues.
The next day when leaving camping it was the same thing. Took off and saw gray smoke and had little power. After about 1-2 miles all was well again. Truck has 202k miles. Recently replaced oil cooler, egr cooler has been welded shut at both ends, turbo has been cleaned and all the filters and fluids are new. I have a Scan Guage 2 and monitored the ficm voltage and it maintained 47 to 47.5 volts. I know 2 injectors had been replaced when I purchased it as well and the egr valve by a dealer(they said it showed the cooler was clogging but like I said it was welded shut). What I should look for?
View 14 Replies
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
View 5 Replies
I went out to the store today all was fine came back out and started driving got 2 miles down the road to a red light and the truck about stalled no power it doesn't smoke at idle but revved up it blows black and some white and the truck shakes. I am thinking its stiction or bad FICM????
View 13 Replies
6.0. 115,000 miles. Everything stock, except bully dog intake filter.
I replaced the FICM recently, with one that I bought from the guy who makes those cool You Tube videos, Diesel Tech Ron. I also replaced the EGR valve. I also replaced the intercooler boots on the hot side. I cleaned the intercooler pipes. I cleaned the intake filter as well. I'm still blowing out black smoke, if I floor it when I need to pass someone.
Follow up question: I bought those boots from Riff Raff Diesel and I bought new clamps, too. I'm not sure if I installed correctly. It's already blown one off (it blew the top of the intercooler pipe off, by the turbo, but the boot stays on the turbo) and I put it back on and tightened it all the way down, and I've had to re-adjust 2 times, now, since it acts like it still wants to slip off. Do I simply have the other ones misaligned???
View 14 Replies
Driving home 2003 6.0 started blowing a ton of black smoke, cars wouldn't get behind me. Found an exhaust leak on the driver side up y pipe. Would that cause this much smoke? 2 codes were 0284 and 0281, I replaced those injectors about 10k ago, at the same time replaced turbo, hpop, egr valve and cooler delete, and new oil cooler.
View 9 Replies
Found a 2004 Ex, Eddie Bauer edition says it has injector issues, blowing black smoke........ It is apart cause he thought it was the EGR. Has 245,000 on the clock. If the body is super clean I'll give him a offer, it's going to get a motor either way and I'll have my Ex back.............I really miss that truck!
View 2 Replies
Ok I have a 2004 f250 6.0L, has 104k on it. A little back story... truck was running well when I started to get surging on takeoff and it was blowing black smoke when it surged. After it hit 1600 rpm it would blow out and run normal. So did some research and found it could be the FCIM, I have the 4 pin and tested it and had 48.5v so it tested good. Did some more research and found symptoms leading towards the ICP so I replaced that and the ICR also.
Upon doing this my surging issue cleared up but now I'm getting a miss around 1200 + rpm weather it's in park Reving it or driving, but it is not throwing any codes, I did check with my code reader. I have also changed both fuel filters and have the EBP sensor on order as I hear they can be troublesome. My question is what should I do next or look at? I was trying to avoid the dealer so I can learn more about the truck in diagnosis.
View 14 Replies
I have a 2006 F350 6.0 litre diesel. The other day I started it up drove away and it was blowing huge plumes of white smoke out of the exhaust. Shut it off.....started it up again after a while then went on a long drive and it went away. What that was?
View 6 Replies
2006 blowing white smoke and sluggish until its driven for a few miles ..smells like fuel .. New head gaskets and the works started after 20 days over below freezing temps nights at 5 to -5 ....
View 14 Replies
I recently purchased a 2011 F350 chassis cab with no bed installed. Have a few questions regarding the exhaust system. When I inspected and drove it noticed some black smoke when under hard acceleration, nothing major though. Other that that the truck drove great. Have not got the truck home yet, a friend is going to pick it up and deliver it in a few days. Based on the visible smoke I was suspicious of the exhaust system but I have no knowledge of what the system is suppose to look like. My experience with diesels and for that matter gas engines is mostly from the days of mechanical fuel injected diesels (70's era farm tractors mostly) and carberated gas engines.
My friend stopped by a local Ford dealer and crawled around under a new 2015 Chassis cab to look and compare to this 2011. It appears that the SCR and DPF are not installed on this truck. Where they would normally be is a section of pipe with a section about 2 feet long that is 6 or 8 inches in diameter. Looking at some threads on this site I'm guessing this is a muffler that has been added since the truck is not loud. There is no DEF tank and all the wiring for sensors that would be attached to the exhaust system appear to be tied off to the frame and not connected to anything. The dealer didn't know the history beyond he purchased it on an auto auction and he installed a new rear end in it. Car Fax shows nothing of concern.
My question is should I now be concerned since have determined much of the exhaust system has been removed? I've read some threads and it appears that the only way this can be done and have the engine run well without any codes etc is if the removal is done with some sort of tune. Is there any way to determine who has done the tune? Will it be an issue when take to a Ford dealer for service?
I know if wanted to put the system back to stock would be large dollars, as long as the system runs well and is reliable I will be happy. The anticipated use of the truck will be to pull gooseneck trailer and will probably not see more than 1000 miles a year towing and 5 to 10k total in a year. I drive with a very light foot seldom ever pressing any vehicle to its limits. If still have the truck in 10 years when retire or at least cut back on my work then it may see more miles.
View 9 Replies
My 2006 6.0 is blowing white smoke/steam and Im losing coolant (not out the top). Pulled the EGR valve and its wet down there. All signs lead to EGR cooler? I've been reading a lot on this forum and Ill do the oil cooler at the same time. I seems VERY important to flush the coolant system before I tear into this. I am afraid of hydro locking the motor or ruining the head gasket or stretching the head studs if I run the truck. How can I do this without further damaging the engine? I am doing this myself. I'll have 3 solid days to finish this job because I have to tow my trailer in 5 days.
View 5 Replies
I just bought this 2007 F250 a 126K miles on it. Drove it about 1500 miles with no problems. I changed the coolant to Rotella ELC, installed Sinister Diesel Coolant and Oil Filter Bypass, and changed oil to Rotella 15W-40. 3 days after I did this it was in the mid 30's in the morning when I headed to town. It was blowing white smoke, so I stopped and smelled it. It did not smell sweet. I saw what looked liked diluted oil dripping from the exhaust. As I turned around it stopped. I revved it up and no smoke. I headed back into town(around 10 miles) no smoke. Drove home and no smoke. I was at home for about an hour and when I started the truck it was blowing white smoke.
I revved it up a couple times and it went away. I drove about 125 miles and no smoke. I let the truck sit about an hour and when I started it was blowing white smoke and no matter how much I revved the truck it did not go away. I went to work and the truck sat for 3 weeks. I just installed the blue spring kit. Started the truck and no smoke at first. Then, when it went to fast idle a little wisp of white smoke. As soon as I revved the truck up it got worse. Then it blew out what once again looked like diluted oil about 5 feet out the exhaust( I have a huge tractor weight sprayed with this). My first thought was maybe with the thicker oil I am getting some stiction so I am planning to change the oil to 5W-40 and add Hot Shot Secret tomorrow. But blowing the oil like substance out the exhaust has me concerned.
View 3 Replies
After running perfectly fine all day my truck will seem to bog down and when I press the accelerator the reaction is extremely delayed and tons of black smoke will come out of the tail pipe before the truck actually gains power and takes off. The check engine light has been coming on but will turn itself off after the truck has been shutdown a few times....
View 10 Replies
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
My 04 PS was blowin white smoke constantly while running. I just towed a uHaul from Connecticut to Virginia Beach and had some coolant issues on the drive down (I was out of coolant on 95 in PA, added coolant and it made the rest of the drive no problem). I got here to Virginia and it was low on coolant again. I added coolant to it, and now I have some other issues. I had what looked like oil comin out the stacks onto the bed, so I pulled the turbo thinking it was seals. But the turbo was just rebuilt prior to me buying it with a wicked wheel in it. It still had stock EGR and it has 202K on it.
Checked and found EGR valve was wet. Ordered an EGR delete kit, and just finished installing it. Now with everything put back together, the truck doesn't want to start. It cranks but doesn't fire. I pulled the codes from my tuner and I got: P0403, P0405, P0683, and P2623. I know P0403 and P0405 are related to EGR but the others I'm at a loss on. The EGR delete kit I bought included the blank to remove the valve but what do I do with the plug that used to plug into it? Any way forward to get the truck back up and runnin again? This is my daily driver and not lookin to break the bank to get it goin again but I really need her to be reliable.
View 14 Replies
I picked up a 2003 6.0 awhile back went ahead and did studs,gaskets, delete. Was driving it and seemed to lose power, started coughing and carrying on blowing bluish white smoke then shut off. Ended up hydrlocking #5, Oring on injector was tore when took out. Put all back together, ran horrible, did a balance test with AE, showed #3 injector, replaced, ran horrible, did AE dropped #1 injector. So in process of replacing the rest of the injectors. Just wondering why it is or was dropping them 1 at a time. Ficm was showing 47.6 to 48.6 volts, could that be it?????
View 14 Replies
I have a 2004 f250 i purchased a month ago. Its been cold in Denver this last month which is why I didn't mind it much. But now that its been in the 70s im concerned. Its always the first start up that it acts up. I go to turn the truck on and it starts idling for only a sec or two, then shuts off. I crank it about 3-4 times before it actually comes on and stays on. There is black smoke not white smoke once it starts to idle. Once idling it stays on and drives the way it should. If i try to start the truck again it will do so with out hesitation. I just did a tune up at grease monkey including fuel filters and oil filter. again its the first start up always.
View 1 Replies
I have a 2013 GT and my wife a 2011 sedan.
[URL] .....
I've looked it up and didn't find any reports of it happening to the GT. (I admit I didn't look too hard!)
It happened to my wife's 2011 sedan when accelerating onto the highway. Just as described in the "massive smoke" thread. I couldn't see the car following behind me, the smoke was that bad. No exaggerating!
-- no check engine light
-- no change in temp
-- car drove fine immediately afterward (we babied it till we got home)
-- oil level and colour OK
-- coolant OK (overflow between lines)
-- next day car felt fine during full-throttle 80-120 km/h acceleration.
-- mentioned it at dealership, with service adviser, service manager and mechanic all listening to the story. They were stumped but offered to look at it. Adviser suggested a "BG Products fuel induction" treatment, which I'm assuming is bogus. (Haven't had a chance to check into it)
My web searching suggests the car had a "carbon blowout" cuz my wife rarely drives on the highway. I've heard of this but always thought it was just a myth. I mean, seriously, have you ever actually seen a car throw up a James Bond smokescreen just cuz it hadn't been driven hard? I'll betcha five bucks that if I took my mom's babied 1997 Camry onto the highway and floored it, nothing would happen. So what's up with the Elantra?
View 9 Replies
I was towing my camper uphill and my 03 6.0 started missing and blowing black kid smoke. Next thing I know I hear a loud pop and steam is coming from under the hood and the truck dies. I pull over and discover the degas lid is stuck on and the bottle came apart at the the seam and the truck will not start. 6.0 with 120k miles
View 1 Replies
