Ford 6.0L Power Stroke Diesel :: 2005 - Quit Running Now Won't Start?
Jul 18, 2016
I'm working on a 2005 F350 with a 6.0. The customer was driving the truck when it suddenly quit running and now it won't start. The only code stored in the memory is P2290 - ICP too low. With my scanner connected the IPR is showing 85% duty cycle and the ICP is only showing 5 psi while cranking. I disconnected the ICP sensor while cranking but still no fire, so I removed it and connected a pressure gauge which shows zero psi while cranking. I hooked up a cylinder leakdown gauge to the ICP port and with 100 PSI of air pressure I'm showing less than 2% leakage with the IPR energized at 60% duty. Thinking the hpop was bad I replaced it but still no change. I also tried a new IPR but no luck there either. I removed the oil filter cartridge and verified the low pressure pump is pumping oil while cranking. Could the inlet screen be plugged inside the oil cooler? I'm at a complete loss.
View 7 Replies
Advertisement
So just recently my remote start quit working. It's worked fine for the last two years. Now after I hit the buttons the truck just honks. I tried going through the setup on the dash and turning it off and back on. Still just honks at me.
View 8 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
I have a 2005 F250 with 6.0 Crew cab
Wanted to change out factory bulbs to LED's. The factories were working just fine, just wanted LED's. Broke a couple of center bulb holder's/clamp. Don't really know what they are called. Went to junk yard got a couple of used ones, those worked because when we opened the doors on wrecked trucks Dome lights came on! Got home put them in and NOTHING. No dome, no map lights with LED's. Changed back to factory bulbs and only map lights come on, NO dome lights on front or back and my 3rd brake light quit along with the 2 bed lights. Checked the wiring plug and have power to one wire. What fuses would I need to check or to check where next? Owner's manual is not very specific about which fuse.
View 1 Replies
I recently noticed my 2005 F250 6.0 was running really cool, like barely making it out of the 170's. I guess it is time to replace my thermostat which I just replaced about two years ago. The question is should I replace it with another stock 192 degree thermostat or go for a 200 degree Mishimoto? I found where some where going to that one and it is supposed to make everything run better and the thermostat lasts longer. Any pros or cons to installing a hotter one?
View 7 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
Early build 6.0 (2003) starts fine in CT winter weather as long as its plugged in, HOWEVER, will not start after engine has been running! It just started doing this a week or so ago and after plowing all day yesterday, it just wont start after the engine is up to operating temp. It will start on a shot of ether but I only did that once to get it home.... Other than that, the truck runs great! I changed the oil today, checked the ficm (48V) and the injectors were all done less than a year ago. The only code I get every once in a while is Cyl 1 injector circuit low and that goes away on its own. I'm not really sure where to start.....
View 4 Replies
Well, I've read a lot of threads on this problem! Try to do my own repairs, so I'm learning and not spending a lot of cash at repair shops.I have an 04 6.0 Super Duty Crew. Starting running rough on way home. Pulled over ,then it died.wouldn't start. Had towed home. Replaced ficm circuit board. No start. Replaced Harness,
icp...... ipr Sensors. Still no start. I noticed there is another circuit board inside ficm. Should I have bought the whole ficm unit?
View 4 Replies
I was towing a trailer about 600 miles truck was running great, pulled in for fuel and truck was running rough, refueled and was on my way then when going down a hill (Idle) it just quit, had to tow remaining 200 miles.
After reading the forums I replaced the ICR (ICR screen was damaged) Truck now starts but its very loud and missing like crazy. and surges if i give it a little gas. codes 0268, 0281, 2284, 2288 I also replaced the ICP.
should I replace the injectors? what causes this?
View 14 Replies
2005 6.0 133000 miles... Truck has been stuttering and running rough for about 2 weeks, warms up and is somewhat better. Would stutter in the RPM range of 1600 to 2100 RPM, can push down on accelerator and power through it with no problems. Checked codes and got PO269 Contribution Cylinder 3. Changed all filters and oil change along with a bottle of hot shot secret in the oil. Truck is now blowing blackish grey smoke under throttle and when idling that smells like fuel. No coolant in oil, and no oil in coolant.is the injector shot, or injector sleeve bad?
View 6 Replies
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 Replies
Driving home from work last night my truck just died. I was under load, going up hill, and she just shut down. No power, completely dead.
She'll crank, but not start.
Ever hear of this?
View 14 Replies
My 05 F350 will not start hot, occasionally stalls when hot as well. Starts immediately when cold and runs smooth as silk. Truck has 138k miles on it, I bought it studded and deleted, running 5w40 Rotella T6 with Archoil. Some history on the issue: Started out with a rough idle, found low FICM voltage along with a bad battery. Replaced both batteries and FICM, problem fixed. Soon after developed a misfire with a cyl 5 imbalance and injector code, replaced all 8 injectors which fixed that issue.
About 2 months ago I had a no start problem, turned out to be a bad ICP, replaced that and the harness and was all good for about 3 weeks. That's when it started becoming hard to start when the motor was warm, and then no start at all when hot and would stall occasionally at idle, wait an hour and it'll fire right up!
Ran the air leak test, found a leak on the right bank standpipe, replaced the dummy plugs and standpipes, no start still remained. Went on to replace the IPR and STC fitting which didn't work either. Now it throws a P2285 code, low ICP. Ran the air test again and I don't hear any leaks. HPOP seemed to have good compression turning by hand.
View 14 Replies
I have an 04 F2 50 with 6.0 with approximately 225,000 miles. I filled up with gas last Wednesday and every so often the truck will start running really rough and then it will clear up. Is it possible to of gotten some bad gas if so what products are out there to clear that up. Could've been injector going bad what are the best products for cleaning injectors. No check engine light on, gauges are good, nothing different on the scan gauge.
View 3 Replies
I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
View 5 Replies
This has me puzzled to no end. After my son had put fuel in my truck it began to run rough, and had to be towed home, and now won't start. Now the first thing I thought was that he put regular gas in. But he was sure he had not ,and the receipt from the pump indicates diesel. It was hard starting before this happened.
1st Misfortune of having gas put in instead of diesel and did your vehicle run afterwards.
2nd Here are my readings from my scangage:
Sync Yes/1, Ficm main power 48.5 v, ICV .17 (2.01 when cranking). ICP 1572. IPR 50.7.
Checked upper fuel filter for bubbles, none.
Engine oil pressure comes up immediately on cranking.
Don't know what else to check, these readings look fine to me. Only the fuel is something I'm not 100% sure of. It does smell like diesel not gasoline.
View 14 Replies
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
View 14 Replies
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
Traveling right now. Limited access to FTE.
On the way to the airport this morning at 4:30 am, the engine simply did while running down the interstate. Absolutely no symptoms leading up to it. Turns over fast but will not start. White smoke from tall pipe while trying to start.
I unplugged the fuel bowl heater and checked the IPR tin nut and the ICP sensor connections... Nothing obvious.
Problem was CPS and the engine is now running fine again.
View 14 Replies
Where can I send pcm off to have checked out.
View 6 Replies
Brother in law company 6.0 died on him in his driveway after a night of plowing
It stalled out, his boss sent out a "tech" and he said it doesn't have "nearly enough" oil pressure
Now I want to further diagnose the truck myself with my scan gauge II but haven't used it for that......yet......
What should I check for IPR pressure psi or %?
I know I can get ICP pressure in PSI on my SCT x4 not sure about the Scan Gauge......
I assume a blown IPR or failed STC fitting......
Truck is a 2005..... I can figure out the scan gauge I just need to know what to look for for an idea of a blown IPR or STC or ICP.
View 14 Replies
