Ford 6.0L Power Stroke Diesel :: 2005 F350 - Lost Power And Won't Start
May 21, 2017
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
Advertisement
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
View 14 Replies
Currently truck is in the shop after having multiple episodes where it lost power. It has 47,000 miles on it. When pushing down gas pedal, just does not want to go. Very slow to shift through the gears and get to highway speed. Turbo was not there, and there was also a hard shift/jerking from 2nd - 3rd. Did notice the traction control sensor kick on a couple of times....which was just replaced since a hole rubbed through the wiring. (took it to Ford twice before they found the problem)
They told me today that the code generator said to look at wiring but they did not find anything (heard that before) and that the fuel is possibly contaminated with DEF. If that is the case, someone is messing with my truck! What I don't understand that if the DEF does turn out to be in the fuel tank, wouldn't we have the problem continuously and not intermittently over a month after driving thousands of miles and going through numerous tanks of fuel? We drive and average of 60 miles per day just for work, half interstate/city.
View 14 Replies
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
2005 F 350 6.0
124000 miles. Drove the truck on a long road trip Saturday ran great. Didn't touch it Sunday. Went out Monday morning and it wouldn't start I noticed the fuel gauge said empty and the low fuel light was on. I knew there was plenty of diesel still in the tank but I still went and bought 5 gal and dumped in it fuel gauge then read over half full but still won't start. A buddy who's a mechanic swung by sprayed starter fluid in it fired right up then died he said I need a new fuel pump. I have been reading the forums. I just want to make sure is he right?
View 6 Replies
My friend has an 05 6.0. He's having a no start issue. He was driving and it cut off, he couldn't remember if it cut off quick or sputtered. I hooked up my AE and jumper cables and stated looking. Cranking the icp would only build up to 190ish. I unplugged the icp sensor and AE was reading 1538ish??, I guess that was a default value. The ipr reading immediately went up to 85% but still doesn't fire. Also while cranking there wasn't any white smoke at all from the exhaust. A few years ago he broke down and Ford put in the updated snap to connect fitting. He said they also replaced the dummy plugs but he didn't mention stand pipes so... I'm not where the truck is so if there's any questions it might take a few.
View 9 Replies
I just got finished putting on arp head studs and gasket, new bulletproof oil cooler and egr delete. Put it back together the way it came apart but it doesn't start. Just turns over but wont start??????? 2005 F350....
View 14 Replies
My uncle bought an '05 that stopped running one day. He was driving down the road and engine lost power. He was able to coast into his driveway. Unfortunately, it's been 10 years since I've work on a 6.0 and no longer have any of my computers.
He did state there is no check engine light. He's going to change the filters today / tomorrow. I'm hoping to make it down there this weekend to look at it, but what to look for. Even more unfortunately, we really don't have any specialty tools or gauges.
View 2 Replies
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 Replies
This is a new truck to me 03 Excursion, the owner has done a lot, gave me receipts for a lot of work and cosmetically it just seems taken care of. About a year ago hpop, ficm, oem egr and 3 injectors. He wasn't happy with that mechanic and still having problems so went to a different (supposedly better) shop. This time turbo cleaned, all 8 injectors and passenger head was redone and put back on with oem bolts. Apparently it was found that a nut was dropped down valve cover by the first shop! Somewhere along the way the ICP and GP module has been replaced.
I've only driven it a couple times and seems great until last night. It was loosing power and in about 10 seconds died and wouldn't start back up. Pops but doesn't stay running. WIF dash light on and no CEL codes. Not sure where to start/what to do. I've paid for most of it and was planning to pay the rest and transfer title but I'm not comfortable doing that till I'm confident it's good to go.
I drained the separator and seemed to gush out like it should and don't think I saw water. I'm planning to take the sensor off the filter there, inspect and clean it but I don't imagine that's the problem. I do see oil coming on the back of the engine and front of tranny on the drivers side... maybe ICP is all oily and failed? I don't know much about these, just been trying to read. What should I do as some first steps? Do I need some sort of scanner? It seems like it's starving for fuel. It was about 1/4 of fuel when I bought it and filled it up the night I took it home and have put about 80 miles on it since. Is it possible it's got bad fuel or water?
View 14 Replies
Had my oil changed on my 2011 F350, and the tech said that I lost one gallon of antifreeze coolant. Where could the coolant have gone? We could not find a radiator or hose leak. I am afraid that the coolant somehow got into the engine oil, and may have damaged the engine. I have 46000 miles on the truck.
View 14 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
View 10 Replies
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
View 9 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
My 03 F350 lost the Brake Lights, and Code B1483 came up, which is the Brake Light Switch. Switch was replaced with new switch, with no change. The new switch was tested, and is working. The mechanic even replaced all the bulbs, which did nothing. The tail lights and turn signals work fine, just no brake lights. The mechanic even called the Ford Dealer in Boise, ID, and their service dept had no clue. What is everyone missing on this issue?
View 14 Replies
I've got a 2005 F350 that i recently did balljoints, tierods and shocks/stabilizer on. Just stating that because i don't believe anything could be binding up to cause this.
If i am to take a left turn, more than 45 degrees, the truck will seem to lose power assist on the return to center and be very stiff when i return it by force until i jerk the wheel past center and let it come back the other direction and it seems to regain power assist.
Also, the steering is just generally bump. I have not driven a better condition 2005 to tell the difference but i'm sure this isn't the way it's supposed to be
I am not having any issue with braking force, as of yet. The first winter i got the truck i blew a power steering line that goes from the gear to the cooler, in which direction i don't know. It's been a year and a half since then so not sure that caused any failure.
Before this symptom the pump would whine when on left turns only, no problem turning right if i feel like doing right turns the rest of my days. I guess what i'm getting at is, does this sound like a bad pump? Bad gear? Both?
View 14 Replies
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 Replies
I have a 2005 F250 with 186K miles. I do minor work on my vehicles but have little experience working on my diesel. I was accelerating when I heard a pop and a hiss similar to disconnecting an air hose from an air compressor. Total loss of turbo power. No turbo reading on the turbo gauge on dash. No loss of oil. No smoke. Oil and coolant look fine. Took off turbo and everything appeared to operate like it should (according to YouTube videos). Inspected lines and rubber boots.
Rubber has some cracks but not certain if they are holes. How small/large of a hole would cause total loss? Was originally scared to take it to a shop knowing they could name their price. Not opposed to taking it somewhere now knowing the turbo works but obviously would rather save the money. Any tips on troubleshooting? I'm not opposed to proactively replacing parts/sensors as the truck has given me 186k and I plan to keep it as long as possible.
View 8 Replies
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 Replies
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 Replies
