Ford 6.0L Power Stroke Diesel :: 2005 F350 - Climate Control Not Working Properly
Aug 30, 2017
I have a 2005 6.0 f350 lariat... My climate control doesn't switch very well I can get it to go to floor sometimes after 15min of pressing the button. The vacuum pump is good the tank has no cracks. I feel that the system is either plugged up or has a leak. I cleaned the tank after my hub seals went and it sucked a ton of dust and dirt through my wheel bearings in to the tank. Is the vacuum switching part of the digital display? Or is there a separate part?
View 1 Replies
Advertisement
I have been trying to figure my cruise control not working. I verified the switch for the brake pedal and the one on the master cylinder are not the problem. I have read about the clock spring but would like to verify signal is passing through/ not before replacing.
2 Questions.
#1 I have is how does the overall system work? Ok not that in depth but, is there some kind of servo that regulates the flow to,the injectors or is it strictly controlled by the PCM? and it tell the injectors to open to allow fuel to pass.
#2 Looking for a wiring diagram for the cruise control control circuit. Namely looking to verify switches are working.
View 14 Replies
First off my vents stopped blowing completely. At this time the thermostat was still functioning. Fuse 28 was blown. I replaced the fuse and it blew again shortly after turning the heater on. I replaced the relay and resistor and still blowing fuses. For some reason I tried a 30A fuse and it didn't blow but a few minutes after turning on the heater there was a burning smell. I immediately turned it off and pulled the fuse back out, which was hot. I then replaced the blower motor and at this point there is no power at all to the control panel. The fuses are all fine as well as the relay and resistor. There's power to the fuses. So it seems like somewhere between the fuse box and the control panel I'm losing power.
View 7 Replies
I have an 02 F350 7.3 ... I just installed my glowshift tripple gauge pillar set. I have an EGT, Boost and fuel pressure gauge ... I followed all the constructions on installing them. The boost is working just fine and the EGT was too, but after a while the needle started going back and forth and the red warning light what blinking and then it just sat at 0 with the warning light on and stay that way. My fuel pressure gauge is connected to a sensore i put in my fuel filter housing, my fuel pressure gayge right from the start stayed at 30 psi with the red warning light on and just stays there .... Also the buttons to change the color and set the peak on the EGT gauge are sticking for some reason and staying down and aren't letting me change the color ...
View 12 Replies
Here is the issue i am having. 2011 F-350 King ranch with all bells and whistles. In Arizona now we are in the season that the weather is cold in the AM and sometimes hot enough in the late afternoon to need the A/C in the truck. with the settings on Auto which i normally do, and the external temp reading in the 80s, and the internal thermostat set at 70 or lower, the A/C compressor will not engage and allow for cooling the cab of the truck. But sometimes it will work just fine. I am assuming there is a temp sensor for cabin temperature. Where that is located. or will i have to change out the entire Climate Control Module. I would take it in to have it checked out but it is an intermittent problem, and i cant not have my truck for a couple of days while they try and figure it out.
View 13 Replies
Cold start the injectors definitely are not "clicking" the way they should be. Bought a scan gauge II and checked the FICM voltage and it never drops below 48V. EOT/ECT never really get past 8/9* ....
Issue is when I first start driving you can feel a definite miss, but as soon as the truck warms up it runs excellent, no issues starting hot. I did put 15w40 in it but upon some research I drained it and put in 5w40 syn and it definitely solved some of the issue but it's still there.
One other note the battery's are a little weak in the truck so tomorrow I will have new ones-putting this in as a side note in case it may cause an issue
View 10 Replies
I have an 06 f250 6.0. When I bought it a few weeks ago I turn the key on and let the glow plugs warm up and start the truck it would start easily. Now it seems like it's taking longer to start . The temperature are between 50 and 80 degrees. I changed the fuel filters and it's still taking to long to start.
2nd I noticed today that when my truck is at idle the Tachometer is at 0 and when I'm driving 60-70 MPh it goes up to 900 or maybe 1200. It seems to be running fine no loss of power that I can tell. What could be causing the long crank time and my Tachometer problems.
the glow plugs and injectors are new I don't remember the brand and the fuel filters are brand new Motorcraft.
View 1 Replies
I recently bought a 2005 F250 4x4 automatic trans with 177,000 miles. In the last 300 or so miles it has developed a whine from under the truck like gears not meshing. It is constant and only the speed of the truck seems to affect the volume of it. It is loudest, considerable louder, on deceleration. Different gears have no effect, 4x4 high or low has no effect, even slipping it into neutral while its rolling has no effect. I have seen various websites about bad wheel bearings, transfer cases, and rear end gears causing this type of noise. There is no vibrations, slipping, shuttering, at anything else unusual. Except for noise it drives ad rides completely normal.
View 2 Replies
I've mentioned in earlier posts that my speedometer has been swinging around wildly off and on, and that on two occasions this has been coupled with a momentary engine stumble. This morning on the way to work it was doing it again but this time the engine stumble happened several times as well. I plan to check the speed sensor, but I wonder how this is also causing the engine stumble?
View 3 Replies
Well, after getting the bed back on my '05 F350, I have been driving it on the road for a few days, but now I have a new problem.
Every once in awhile I get lag off idle for about a second, then the turbo spools and everything is fine. Other times, I step on the accelerator a bit from a stop, and the truck acts like its going to die for a moment, a puff of black smoke, and then the turbo spools and all is back to normal. It a combination of these two problems happens about 3-5 times out of 50 stops a day.
I have a scanguage and everything looks normal and I never get any codes when I check.
View 14 Replies
I have a bone stock 2005 F350 DRW FX4 6.0 Diesel. I've been averaging 10.5 to 14 MPG city. Haven't really done any hiway driving yet.
View 14 Replies
2005 F 350 6.0
124000 miles. Drove the truck on a long road trip Saturday ran great. Didn't touch it Sunday. Went out Monday morning and it wouldn't start I noticed the fuel gauge said empty and the low fuel light was on. I knew there was plenty of diesel still in the tank but I still went and bought 5 gal and dumped in it fuel gauge then read over half full but still won't start. A buddy who's a mechanic swung by sprayed starter fluid in it fired right up then died he said I need a new fuel pump. I have been reading the forums. I just want to make sure is he right?
View 6 Replies
I have 2005 f350 will not shift on the fly. With a vacuum pump it will hold vacuum at both hubs but will not lock up. The seals should be good.
View 11 Replies
My 05 F350 6.0 won't turn over with the key, everything comes on like normal but won't turn over. Starts fine with factory remote start. What to check?
View 3 Replies
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
View 14 Replies
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
View 10 Replies
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
View 9 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
I just bought an 05 F350 and it starts fine when cold but after I drive it a while will not start even after sitting for up to an hour (overnight cold start fires right up). I replaced 1 battery and alternator and it started up right after install but after driving for a while still have the problem - cranks fine but will not start.
Buddy of mine has the same truck (just a 250) and had this same problem recently and had to replace the High Pressure Oil Pump, which was super expensive! This is my first diesel truck and it runs like a champ (once it starts!)
View 1 Replies
I recently picked up a 2005 F350 6.0. I got it cheap with a plugged oil cooler, and went in planning to do studs, gaskets, and all the Ford updates just to have it out of the way. When taking it apart, I quickly noticed that the compressor was damaged. Looks to me like some foreign object(s) entered the turbo, would bounce off the wheel, impact the cover, and repeat.
Engine seemed to run great. Turbo spooled quickly and while I wasn't paying close attention, I'd glance when accelerating and it'd be in the neighborhood of 27 PSI. Engine cranks evenly and starts well, so there's no obvious engine damage. I'll inspect the bores closely with the heads off.
So my main question: Assuming no damage elsewhere, Do I need just a wheel? There is some pitting and high spots on the cover, but could it be carefully worked down with the cover removed? Do I just need to get a wheel and a cover? Or just a whole new turbo? Looking for a budget-friendly option to remedy this properly.
View 7 Replies
