Ford 6.0L Power Stroke Diesel :: 2005 F250 Running Really Cool / Thermostat Replacement?
Jun 15, 2017
I recently noticed my 2005 F250 6.0 was running really cool, like barely making it out of the 170's. I guess it is time to replace my thermostat which I just replaced about two years ago. The question is should I replace it with another stock 192 degree thermostat or go for a 200 degree Mishimoto? I found where some where going to that one and it is supposed to make everything run better and the thermostat lasts longer. Any pros or cons to installing a hotter one?
View 7 Replies
Advertisement
I'm about to replace my IPR and my thermostat, and just watched a video saying after replacing the thermostat you need to bleed the air out of the system to get rid of air pockets so you don't overheat the engine. Is this true and if so how do you do it? Also, how much coolant do I need to drain before taking off the upper radiator hose?
View 2 Replies
2013 6.7L F-250
The owner's manual recommends idling for a period of time after towing to allow the turbo to cool somewhat. After towing a 10K lb travel trailer in the mountains, what temperature should i shoot for as sufficiently cooled? When towing the oil to averages about 210-215-F. Normal operating temp is about 190F.
View 14 Replies
I have a 2006 f250 6.0. the truck has 101k miles and to this point I have had zero issues. I am having trouble loosing power after running at highway speeds. Once I stop and begin to accelerate the truck looses power for a few seconds ,Belches smoke and begins to operate normally. I had an egr code, so I replaced egr and the problem persist. It is intermittent and does not happen if I stay under 50 mph.
View 12 Replies
I have a 2006 Fod F250 with the 6.0 Diesel, I just got it back from the shop after doing Ficm, Injectors, Glow Plugs, Glow Plug harnesses, and brakes. I have driven the truck about 200 miles and got it back to the shop and parked on a hill and rewired the 7 way trailer harness. Now it will start for a second or two and then die. I checked all fuses(dont know how to check relays), pulled DTC and got a low fuel pump voltage. I pulled the IDM relay and was getting power to 2 of the 4 terminals and plugged the relay back and was getting power to 3 of four terminals(not sure if Im spose to have power to all 4), not getting power to the IDM 10 amp fuse in engine compartment either.
View 2 Replies
I've been fighting some issues with my 05 f350 6.0 I'm pretty sure I have it narrowed down to a failed central junction box. I have no power to the pcm. I bought a used one off ebay that was supposed to fit my truck but some fuse/relay locations are different. All the plugs on the backside appear to be correct though. Do I need to get a fuse box that is the exact same part number that is currently in my truck? 2C7T-140A067-AN is the part number of the one in my truck. Or can I use the one I bought?
View 9 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 Replies
Ok, so I have a 2004 F250, with 6.0L. when driving at a steady speed (doesn't matter what speed), the engine will run rough when coming to an idle, and stay running rough until I shut it off and let it sit for a bit.
After I cycle the key a few times it will fire up and run fine, so I came to the conclusion that air is getting in the fuel system. I then took the filter cap off that is located in the engine bay and cycled the key, which produced a lot of bubbles, which I am assuming shouldn't happen.
I guess my question is, should I have air bubbles in the filter bowl, when cycling the ignition?
View 1 Replies
I'm working on a 2005 F350 with a 6.0. The customer was driving the truck when it suddenly quit running and now it won't start. The only code stored in the memory is P2290 - ICP too low. With my scanner connected the IPR is showing 85% duty cycle and the ICP is only showing 5 psi while cranking. I disconnected the ICP sensor while cranking but still no fire, so I removed it and connected a pressure gauge which shows zero psi while cranking. I hooked up a cylinder leakdown gauge to the ICP port and with 100 PSI of air pressure I'm showing less than 2% leakage with the IPR energized at 60% duty. Thinking the hpop was bad I replaced it but still no change. I also tried a new IPR but no luck there either. I removed the oil filter cartridge and verified the low pressure pump is pumping oil while cranking. Could the inlet screen be plugged inside the oil cooler? I'm at a complete loss.
View 7 Replies
I recently had my injectors changed at Ford and while I was driving it started dumping coolant. If the leak can be cause from the injector replacement or if they didn't put something back together right... 2005 f 350 6.0...
View 14 Replies
My 2003 F250 started to sputter and died. Won't restart the rest of thw day. Go out next morning will start right up for about 1-2 min and dies like you shut thw key off. Won't restart. Cranks fine.
Oil pressure showing 1300lbs while cranking,ipr is 43% while cranking, but when koeo ipr is 97% which is weird. My excision shows 23% koeo.New oil,oem filters,fuel pressure is at 50 lbs while cranking. Seems electrical or something. Oil pump maybe but why 1300 lbs while cranking of that?
View 14 Replies
I have a 2005 Ford f250 Diesel 4x4 with - unfortunately - the crappy 6.0 engine. Yesterday my Daughter parked in the yard and this morning the truck not only will not start but will not even turn over. I thought maybe the batteries were dead but that is not he case. When you turn the switch on you can hear the pump start up but it will not turn over? All the lights come on and the bell comes on when you open the door and the dashboard lights work but the thing will just not turn over. I am assuming this may be some type of electrical issue or something but whatever the problem is it just came out of the blue. Ford imo should have recalled this engine.
View 14 Replies
I have an 05 f250 with 109k. Recently I turned off my truck, waited about 45 min or so and upon returning the truck would just crank and crank with no fire. After waiting about 4hrs the truck started right up like nothing was wrong.
Yesterday it did it to me again. This time I have it a small shot of starting fluid and it fired right up and ran like a champ all the way to the shop..... I got the call today from the mechanic saying I have 5 injectors that are bad, 2 glow plugs and harnesses. His quote was 2400 out the door.
View 5 Replies
I had this truck for two months no problems yesterday went on a small trip about 50 miles in on ,the hwy. I start seeing some smoke and then no power turned off & on engine several times a little hard starting no power at all I put the pedal to the floor It barely moves ran into another super d. guy he said fuel filters , I turned around and crawled back home and changed fuel filters still no power. no codes "don't no where to start".
View 8 Replies
I recently purchased my 2011 F250 Powerstroke a week ago today with 87000 miles on it. the dealer assured me they did all the maintenance on the truck before i was able to drive it home. I noticed on my dash that it kept popping up i needed to change oil soon.. so i got out to investigate and realized i was about a quart low on oil so i looked around more and am seeing that i have a leak coming from the back of the engine running down to the oil pan.. I have not noticed any on on the ground at all but what this leak is coming from...
View 14 Replies
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....
View 14 Replies
I have a 2005 F250 6.0l. I have no speedo and the ABS light is on. It was intermittent at first. It would go on and off if I hit a bump or braked quickly, but now for the last month the light has been on constantly.
I have tried the following to no avail:
1. check the harness to the VSS (rear ABS senor on the pumpkin)
2. replaced the VSS on the rear
3. check the lines from the vss for resistance and open short (and short to ground)
4. checked the HS-can network (pins 14 and 6 in the DLC to the respective HS-can + and - on the module) both have less than 5 ohms (about 3 ohms found) and no short.
5. checked the resistance of the network itself across pin 4-16 and found 60 ohms.
6. ran scans with OBD fusion for ABS (no abs found)
7. ran scans with forscan with laptop, does not detect ABS unit neither new or old module. note the TBC and IC both throw codes about not detecting the ABS.
8. check HS-can on the PCM as well as VSS wire from abs to pcm, no shorts or resistance.
9. check the number 11 fuse, (good) checked ALL fuses, only bad fuse found was trailer light number 20 engine bay. issue was a wire at the tailer connector was t-taped and not sealed leading to a short to frame.
10. checked the connector to the ABS module for power on both constant power pins, for open ground on both grounds, and power on run, all with in spec.
I've been diagnosing this for the last week, I am running out of things I can think of to check.
View 12 Replies
This is my first winter with my 05 F250 that has the 4wd controls on the floor. I'm just trying to figure out the proper way to put in in and out of 4wd. I did some reading and everyone talks about engaging the hubs, but my truck seems to have automatic hubs because the selector Is not on the outside of the hubs. Am I missing something obvious or am I just reading the wrong things. When I bought it at the end of summer, we tried 4wd out but only for a second and it would grind and be generally unhappy when we were doing it (while driving slow, and complete stop to go to low).
View 14 Replies
