Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Shuts Off For No Reason / Codes P0606 And P0341


Jul 30, 2017

I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.

When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....

View 11 Replies

Advertisement

Ford 6.0L Power Stroke Diesel :: 2005 F250 Shuts Off On Its Own For No Reason

This has happened twice now, both times immediately after towing. I'll start it, begin to accelerate, and it will just putter out. It'll start right back up but it'll putter out again. After 20-30 minutes it'll start (and run). I have an edge programmer and it doesn't turn on when this happens. I get a turbo warning on it that the psi is at like 43/46 even though I'm essentially at idle so it seems to be getting a faulty error thinking the turbo is under too much load.

View 6 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Not Move When Stop At Light Or For Any Reason

I have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?

View 6 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Battery Light Comes On / Engine Shuts Off Seconds Later

Last week my battery light came on for the first time in years. I have a 185 amp DC Power alternator after dealing with so many bad oem ones.

Anyways, battery light came on when i pulled up to a stop sign. I proceeded to plug my sct x4 in to see what the voltage was, with the battery light it was 11.50. I shut the truck off started it back up, no light and voltage was 13.7. Went through the stop sign got into some more traffic, started to accelerate again and this is when the truck shuts off for the first time. Put it in neutral, and it started right back up.

Several days later it shut off on me two times back to back. It was a cold start, and both times the battery light was on and the truck would die within 30 seconds. Third start it kept running fine.

This past Saturday morning battery light was on, let it idle for awhile then as i tried to park it in the garage it shut off. Started it up, no light so it ran fine. Later when i started the truck it shut off again. So it has shut off on me 5 times in the last week.

Some more background on the truck:

2005, 199k miles
Well maintained (T6 every 5k, filters every 15k, etc.)
The injectors are going bad, it started running rough saturday 1/9/16, just a couple days before it started shutting off.
I used to a sct x4 to pull codes, i have p2237 (if i remember right) which is an intermittent icp signal. I replaced the pigtail and icp less than a year ago because of the same code.
And three codes for glow plug solenoid open on 5, 6, and 7.
No ipr codes

View 2 Replies

Ford 6.0L Power Stroke Diesel :: 2005 Truck With Low Boost And Gasser Codes

This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:

P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??

The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?

All my years of information on 6.0's was stolen with my laptop last year ....

View 13 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Wandering To The Right

My 05 F250 CC 4x4 had a problem where it was wondering to the right.

I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).

Had two new front tires installed/balanced and the problem seemed to go away for a few months.

Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?

View 2 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Codes P0279 And P0281 / Injector 7 Bad

I have a problem with my 2005 F250 6.0 with about 156,000 give or take. Started having a problem a few weeks ago started missing and fuel mileage went south and had it scanned. Codes pulled was P0279 and P0281, I was told probably #7 injector bad so I replaced it cleared the codes and Cranked right up no problems until a few moments later the truck started acting up again. Run smooth than rough idle, smooth, rough idle. Same codes! Tested the FICM while on the truck, it showed like 47.5 volts before cranking and 48 volts when cranked.

I have tested the Ohms between the Injector harness end and FICM end. Pin #2,3,4 all showed 0.3 Ohms, #1 did not even register like 0.L on my Ohmmeter. Took FICM all the way off and it made a rattling sound inside, took it apart and about 4 pieces of what a buddy says where resisters. SO I guess my question would be , is FICM bad? Did something short it out, and/or is the number 1 injector wire bad. Plus the when I took the FICM off the back 2 bolts where loose, so I guess the FICM was bouncing up and down maybe. The front 2 where tight.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Will Die For No Reason

01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?

View 6 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Will Run For A Few Minutes Loose Fuel And Stopped

I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem

View 12 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank

So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical

View 5 Replies

Ford 6.0L Power Stroke Diesel :: 2004 Truck Randomly Shuts Off While Driving

04 with 170k miles. truck runs fine. every now and then truck shuts off while driving. turn it off the it restarts every time. Only code that comes up is number 6 injector. The contribution test injector is firing right. FICM voltage is 47.5. has new ipr and hpop also 6k miles ago. Could it be number 6 shorts out or something crazy killing truck? or maybe a crank sensor.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: Truck Shuts Off Abruptly While Driving Or Idling

Yesterday, my truck began to shut off abruptly. Under every condition, from idling to slow running (30mph), and 70 mph, to load and no load. Wait 1 minute and it would start and run for 1 minute 15 seconds. If the batteries were disconnected, the truck would run for 13 minutes before shutting off. Have replaced the fuel filters. Still does it, but runs for between 10 and 20 minutes before shutting off.

Am seeing only two errors codes. P1000, and P0603. I was 40 miles into the Ville Vidal, when this started, and 150 miles from home. To get home, I disconnected the batteries too many times to count, and bled the HFCM numerous times. Am also seeing the moisture in fuel icon on teh dash light up when it quits, but so far as I can tell there is no moisture in the separate.

2003 F450 6.0, automatic. 150K miles.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2006 Truck Shuts Off In A Hard Pull

I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.

View 10 Replies

Ford 6.0L Power Stroke Diesel :: 2004 F350 - Buzzing After Truck Shuts Off

2004 f350 after i shut the truck off something was buzzing. So I popped the hood and found its the injector harness or injectors.Is this normal or something I need to look into?

View 3 Replies

Ford 6.0L Power Stroke Diesel :: 2007 F350 Battery Died / DTC P0606

My 2007 F350 6.0l DRW LARIAT battery voltage was too low to restart her while out and about today. I did notice that she seemed kind of when I started her up leaving my town to got over two towns away. So i set my Scan Gauge to check voltage and it was low considering she was running, in the low 12V range with radio and a/c running. So I figured the regulator is on it's way out but I this be able to restart her up. Anyway after a jump she started right up and I was able to get home no issues. After I jump started her the check engine icon was illuminated with DTC P0606. I'm not 100% on why this trouble code was recorded other than the fact that I tried to start her up which caused battery to fall below the 9.6V threshold to power the PCM. The voltage was still low after jumping her, so I figured i better swap in a new alternator but what kind. I hear that the alternator is an issue with this truck, so what should I get?? What alternator is proven to last on these trucks?

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2003 F250 Turns Over / Starts And Immediately Shuts Off

I have an 03 f250 that i think is getting air in the fuel line when it sits. It turns over starts and immediately shuts off. Then i have to crank it for a minute or so before it will start. After that it is good all day. Next day it might sputter on start but stays on. More than a day it shuts off immediately and needs cranking for a minute...

View 13 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes

I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.

View 7 Replies

Ford 6.0L Power Stroke Diesel :: No Crank Mainly During Colder Temps - Code P0341

I've got a no crank issue this morning. This truck has done this randomly off and on, mainly during colder temps, but normally if I hold the key in the start position for a few seconds it will crank. This morning, no such luck. Batteries are good, everything has power, I can hear the starter relay clicking when I turn the key to start but it won't turn over. It never does this during warm weather. It got down in the low 40s last night and it's rearing it's ugly head this morning. The only code is the P0341, camshaft position sensor, but I don't know if that would be the cause of this or not. It's a starter issue or the CPS?

View 4 Replies

Ford 6.7L Power Stroke Diesel :: Truck Has No Power Barley Moves / Codes PO113 And PO4DA

OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.

View 1 Replies

Ford 6.0L Power Stroke Diesel :: Randomly Shut Off When Pulling Into The Driveway - P0341 Code

A Little Background, my FICM wasn't bad per se but it would dip below 45 volts when the outside temp was around freezing. I pulled it and sent it for repair at the same time the Atlas 40 tune was loaded into the FICM.

First few days of driving mileage was better, truck ran great. All of a sudden one day pulling into the driveway it randomly shutoff. Two occasions since it has acted goofy at started, bucking a little a low throttle. Mileage has returned to how it was before I had the FICM fixed and ATLAS tune applied. To this point I had no codes at all.

Now today it randomly throws P0341 - Camshaft sensor out of range.

So heres the question - do I replace the sensor or try to get at the harness for inspection? Out of range would usually mean the sensor itself is failing while open circuit is usually wiring related. I know its uncommon for this particular sensor to fail but i'm not sure which direction to go.

View 7 Replies

Ford 6.0L Power Stroke Diesel :: Truck Would Not Start And Threw FICM Codes

My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?

View 12 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved