Ford 6.0L Power Stroke Diesel :: 2005 F250 - Intermittent No Start / Idle About 15 Minutes And Died
Feb 7, 2017
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 Replies
Advertisement
I need to get my oil cooler replaced but that's besides the fact. I drove it on a little trip the other night ran fine. Then went to start it after i was done with what i was doing turned it over didn't start the first time. Cycled the key and cranked it again. Started up drove it back home on the high way no spitting or sputters got off the high way it started idling like crap and shaking as i accelerated but made it home. Let it sit over night and day (was at work) got home to start it and it fired up no problem but still idled funny.
Revved it a couple times and it seemed to clear up so i took it around the block. Floored it and it ran like it was suppose to then go to the other side of the block floored it again and it had no power and sounded like it was running on 4 cylinders. Pulled it back in the driveway idled weird and cleared up again went down the street and floored it ran like a scaled ape and then just died. tried cranking it over and nothing finally got it to start after holding the ignition on ran and then died again. Got it pushed home and decided to fire again after a VERY long crank and it idled for a couple minutes very horrible and died on its own and hasn't started since.
View 14 Replies
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
View 13 Replies
Been chasing my tail and can't figure out an electrical issue. My issue is that I'll drive for about 20-30 min and the truck will shut off while driving. I'll pull off the road, let it sit for 10-20 min (cool down) and It will fire back up and go for another 15 min or so. Sometimes it will glitch/wig out when i try to start or not start....
I've replaced the following and monitored everything on a scanner.
-cam sensor
-crank sensor
-2 new batteries
-flashed the ecu
05' F250 6.0 King Ranch 4X4
View 5 Replies
My 2005 Excursion, at 198K miles has become more of a 'hangar queen' in that I only use it for big jobs. I've kept it for towing/hauling and making long highway runs with more than 4 people.
The truck, 99.8% of the time, runs super. It pulls like a locomotive and gets decent fuel economy (17 mpg running 75 mph empty). I've got the 'blue spring', EGR delete, ARP headstuds, 4" MBRP, Banks intercooler, and run my SCT tuner all the time on "8000 lb tow".
But...there is this weird intermittent problem. It appears to only happen when it is warmed up and driving around town. Sometimes, when I pull up to a light, with my foot on the brake, the engine will sort of go into a 'lumpy race idle' and you have to clamp down on the brake pedal to keep it from lurching into the guy in front of you. Other times, it just runs rough and idles 'lumpy'. It has only died maybe 2 times when acting up. Often, the symptoms disappear on their own and don't come back. If I turn off the engine and re-start (to keep from scaring people at the bank drive-through) it usually runs fine after restart.
I've got an EDGE CTS monitor so I've been trying to find out from that what is going on. I can't seem to catch the parameter that might tell me. My local 'indy' shop can't find any codes thrown. The truck had new alternator, batteries, and starter motor installed in January this year. These symptoms have been going on for several years. Recently, they seem to occur more often.
I've searched on this site a few times, but with no definite 'hit'. I'll admit that I'm a big out of the jargon. I keep thinking this is related to FICM, but everyone seems to say the FICM would manifest as a cold start problem. I do know the FICM sits right on top of the drivers side valve cover. It has got to get hot.
FICM?
Injectors?
How do I kill this one strange problem?
View 7 Replies
I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 Replies
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 Replies
Went out to start my truck this morning and it wouldn't start. Cranks fine and almost started once but died. Checked all fuses all my voltages are good. Oil and coolant are good. When I turn the key on I can hear the fuel pump and sounds like it's priming correctly. Might be an issue with a clogged fuel filter? Maybe? Haven't had any problems or issues otherwise.
View 6 Replies
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 Replies
I have an 05 f250 with 109k. Recently I turned off my truck, waited about 45 min or so and upon returning the truck would just crank and crank with no fire. After waiting about 4hrs the truck started right up like nothing was wrong.
Yesterday it did it to me again. This time I have it a small shot of starting fluid and it fired right up and ran like a champ all the way to the shop..... I got the call today from the mechanic saying I have 5 injectors that are bad, 2 glow plugs and harnesses. His quote was 2400 out the door.
View 5 Replies
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....
View 14 Replies
2005 Ford F250 6.0 Diesel (bought new). Never had a problem with the engine until about a month ago. Engine has 220,000 miles on it. Oil and filters changed regularly. Ran low (not out) of fuel, started sputtering badly but not killing. Filled up with diesel. Ran better, managed to get home. The next day it was dead. Crank but no start. Since then I have done the following (not in order):
- Changed EGR
- Changed ICP
- Changed IPR
- Changed the STC fitting
- Changed all seals in the HPOP
- Changed glow plugs and harnesses
- Tested each fuse and relay
- Installed new batteries
- FICM tested 48V
- Changed motor oil and filter
- Changed both fuel filters
- Checked for water in the fuel
- Purged air from fuel line
- Replaced dummy plugs
- No codes
- Prayed the rosary
One month later, still crank no start. Thinking about using it as target practice with the AR-15.
View 14 Replies
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
View 14 Replies
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
View 14 Replies
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 Replies
I have looked through every post and idea possible with no remedy for my no start condition. I have tried everything that I am capable of doing without diagnostic computers and other specialized tools. A little history of what happened. While idling in the parking lot for a few minutes, truck all of the sudden start running rough, and acts like it is going to quit. Hurried out of the parking lot to make sure that I made it home, but the the truck would only get up to about 25 MPH, but I finally made it home(about 3-4 miles).
NOW, the truck won't start at all, but just cranks. Some more detail about how it cranks. It cranks fast, I separated the batteries by disconnecting the grounds on each, and made sure both are charged. Batteries are only 3 months old from Ford Dealership. As the engine cranks, oil pressure registers after a little while, (longer the first time for some reason), and as soon as oil pressure shows up on the dash indicator, black smoke starts coming out of the exhaust. The engine is trying to start a little bit, but it mostly just cranks.
Things that I've done: Changed fuel filters, Motorcraft (new orings). At first the pump was pumping large bubbles through the line up into the upper fuel filter, but after sitting it appears that it is not pumping bubbles anymore, and I cycled the Key more than 10 times. Did the bubble test while upper filter was removed. Unplugged ICP sensor. Pulled EGR, installed new one. Pulled oil filter and made sure that oil is pumping.
Checked FICM voltage, with key on Injectors buzzing, also engine cranking for quite a while. Never dropped below 48.5 V. Pulled FICM just incase and performed repair procedure, still same volts and no start. Coolant level is good. Checked oil level. unplugged EGR. Checked filter Minder. checked for chafing on FICM harness. Unplugged MAF. Checked FICM relay operation, Fuses all around. I need this truck to run.
View 9 Replies
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 Replies
Rough idle I have had for little bit.Would stall out at idle or a stop, but fire right up? No one could figure it out with the stalling, but now its bad, started yesterday. Have white/blueish smoke sometimes, ( white smoke smells fuel) on restart after warmed when it dies, first time it took 25 mins to restart, now only takes 5 to 15 mins, when I step on it INCREDIBLE full power, fuel mileage gone to hell also since yesterday. Had full tank, now 1/2 tank.
No problems on cold start at all, no check light, 325,000 and never had this before.
Bad fuel?
ICP?
FICM?
Recent work, new turbo, ( turbo was original turbo installed when built) cooling line to waterpump, oil change, new fuel filters, front brakes and 2 new batteries.
View 5 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
While driving home the other night at highway speed my truck lost power. I just filled the tank about 15 miles before then and everything was running fine. No lights came on the dash before the truck died and now can't get it started. Bad fuel? Clogged filter?
View 5 Replies
