Ford 6.0L Power Stroke Diesel :: 2005 - Engine Lost Power When Driving Down The Road
Feb 28, 2017
My uncle bought an '05 that stopped running one day. He was driving down the road and engine lost power. He was able to coast into his driveway. Unfortunately, it's been 10 years since I've work on a 6.0 and no longer have any of my computers.
He did state there is no check engine light. He's going to change the filters today / tomorrow. I'm hoping to make it down there this weekend to look at it, but what to look for. Even more unfortunately, we really don't have any specialty tools or gauges.
View 2 Replies
Advertisement
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
So I was driving down highway when I lost power. Engine was still running just had no power and would blow black smoke when I got on the accelerator. I pulled the EGR valve and noticed it had rocks stuck keeping the valve open. Cleaned it all up and put it back in. Went for test drive and seemed good again until few miles in same problem. Took it apart again and same thing.. rocks. I did this 3 times with same results...rocks getting stuck in my valve.
View 1 Replies
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 Replies
I have a 06 f350 with 140,000mile and today I was driving to a buddy's house and the truck died on me as I was doing 45mph so I towed it home and check the codes I have 1 low icp pressure and 1 low icp during starting / cranking and 1 ckp out of range I think that how it's worded so I looked at the icp pressure and it's 0 and the desired is around 1000 and the volt is .56 and as far as the ckp the rpm are reading so I don't know what to do about that ? Could the STC fitting and dummy plug and standpipe o rings really go out on me like this ? Or am I missing something? I am also trying to track down a oil pressure gauge for the Icp fitting to check it
View 9 Replies
i am recently a new owner of a 2006 6.0 F-350. So like any other used rig, it has its quirks. So the one that is bugging me to s the steering. It has been surging hard while driving. It mostly does this when cold. It feels like it's bouncing back and forth then I have to stop and force it from lock to lock. Once I do this it seems to stop it till the next day. I checked the PS reservoir and it's full. The power steering pump looks like it has a slight leak but doesn't seem to be a major issue. The lines going into the steer box are clean and no leaks...
View 8 Replies
I have a 2005 F250 with 186K miles. I do minor work on my vehicles but have little experience working on my diesel. I was accelerating when I heard a pop and a hiss similar to disconnecting an air hose from an air compressor. Total loss of turbo power. No turbo reading on the turbo gauge on dash. No loss of oil. No smoke. Oil and coolant look fine. Took off turbo and everything appeared to operate like it should (according to YouTube videos). Inspected lines and rubber boots.
Rubber has some cracks but not certain if they are holes. How small/large of a hole would cause total loss? Was originally scared to take it to a shop knowing they could name their price. Not opposed to taking it somewhere now knowing the turbo works but obviously would rather save the money. Any tips on troubleshooting? I'm not opposed to proactively replacing parts/sensors as the truck has given me 186k and I plan to keep it as long as possible.
View 8 Replies
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
View 9 Replies
OK here's the deal. Cruising down the road at 55 mph, I felt a pop and then the engine just stopped running.
When I tried to start it up, no oil pressure. It appears that the IPR valve may have failed, but I'm curious if the pop was a catastrophic IPR failure or an indication of something else?
View 7 Replies
I've got a 2012 F250 SD and when i go over some bumps in the road or even down a gravel road, the door panel on the driver side vibrates and it's noisy. Is there any way to pull the panel and add some foam padding or something to stop this? I can see the panel vibrate or heck, maybe it the whole door.
View 10 Replies
I have a 2000 f350. Lost power whole driving and won't start back up. I have checked all my fuses and relays several times. Have no power to the fuel pump. Tried running a hot wire straight to the pump and still nothing.checked my emergency cur off switch and there is no power there. Also my WTS light isn't coming on now. Tried checking the heater bowl and no power there.
View 6 Replies
My 2004 6.0 has lost some power and the head gasket is leaking into the coolant. How long can i continue to drive the truck before too much damage is done to the engine?
View 10 Replies
I have a 2003 6.0 when it has having troubles trying to cut out when running low rpms but would throttle out of it then it lost all power cab filled with smoke and died now it does nothing won't even try to turn over everything under the hood is covered in soot I'm ready to pull the cab just wondering if I didn't loose any oil or coolant...
View 6 Replies
I added LED lights to illuminate the running boards on my Lariat. Did this about 15 months ago and all was fine until this week and I noticed they weren't coming on any longer. Both sides are out of commission. The running board lights on each side are wired to the respective plug for the running board lights on each side. The interior lights that are on the same circuit work fine (fuse #12 in the passenger side fuse box).
So I'm scratching my head trying to figure out why both sides have gone out at the same time but the fuse is ok. It's winter here and my truck doesn't completely in the garage so I'm hoping to limit my time lying under the truck out in the cold, on a wet floor! I thought there might be another fuse in the engine compartment fuse box but there isn't, at least according to the manual.
View 6 Replies
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 Replies
Currently truck is in the shop after having multiple episodes where it lost power. It has 47,000 miles on it. When pushing down gas pedal, just does not want to go. Very slow to shift through the gears and get to highway speed. Turbo was not there, and there was also a hard shift/jerking from 2nd - 3rd. Did notice the traction control sensor kick on a couple of times....which was just replaced since a hole rubbed through the wiring. (took it to Ford twice before they found the problem)
They told me today that the code generator said to look at wiring but they did not find anything (heard that before) and that the fuel is possibly contaminated with DEF. If that is the case, someone is messing with my truck! What I don't understand that if the DEF does turn out to be in the fuel tank, wouldn't we have the problem continuously and not intermittently over a month after driving thousands of miles and going through numerous tanks of fuel? We drive and average of 60 miles per day just for work, half interstate/city.
View 14 Replies
This is a new truck to me 03 Excursion, the owner has done a lot, gave me receipts for a lot of work and cosmetically it just seems taken care of. About a year ago hpop, ficm, oem egr and 3 injectors. He wasn't happy with that mechanic and still having problems so went to a different (supposedly better) shop. This time turbo cleaned, all 8 injectors and passenger head was redone and put back on with oem bolts. Apparently it was found that a nut was dropped down valve cover by the first shop! Somewhere along the way the ICP and GP module has been replaced.
I've only driven it a couple times and seems great until last night. It was loosing power and in about 10 seconds died and wouldn't start back up. Pops but doesn't stay running. WIF dash light on and no CEL codes. Not sure where to start/what to do. I've paid for most of it and was planning to pay the rest and transfer title but I'm not comfortable doing that till I'm confident it's good to go.
I drained the separator and seemed to gush out like it should and don't think I saw water. I'm planning to take the sensor off the filter there, inspect and clean it but I don't imagine that's the problem. I do see oil coming on the back of the engine and front of tranny on the drivers side... maybe ICP is all oily and failed? I don't know much about these, just been trying to read. What should I do as some first steps? Do I need some sort of scanner? It seems like it's starving for fuel. It was about 1/4 of fuel when I bought it and filled it up the night I took it home and have put about 80 miles on it since. Is it possible it's got bad fuel or water?
View 14 Replies
it's now 1,500 miles away on the side of the road.White smoke, knocking and lost power. Truck has 133,000 reman engine installed at 46,000. Is it common for hydro locking to bend a rod? He sent a video and it def sounds like a rod and degas is empty.
View 9 Replies
I have a 2005 6.0. I just got done doing the HPOP seals, injector o-rings, stand pipes and dummy plugs. I have drove the truck 600 miles since the work with no problems other than a wiring issue I got fixed...
I was driving at highway speeds, and all of a sudden I lost power and got a shake when trying to accelerate. I pulled over and turned it off, and when I went to restart it I got nothing at first, then it went to what seemed like a partial crank followed by a thud. So I'm thinking I just hydro locked it. I waited a few mins and tried again, and it started but had a few knocks for 15 seconds or so, then it ran rough with smoke pouring out of the exhaust (grey then turned kinda white).
I the only codes I have are for the egr which I've had unplugged for a long time, and a glow plug code, but when I started it back up, I had no codes. I'm baffled. I did notice I have oil on my oil filter housing at the cap, a little oil had slung on to my wire harness and my intake. I don't even know where to begin!
View 14 Replies
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
While driving a mountain road (hwy 17) going downhill this morning I lost power braking and power steering and a got the following error message on the display
TRANSMISSION P LOCK MECHANISM
PARK CAR ON FLAT SURFACE AND APPLY BRAKES
I was able to stop the car on a flat area. I turned the ignition off and then restarted the car and the power steering and brakes came back, but the red triangle remained. I drove to the Toyota dealership and left the car for service.
View 12 Replies
