So... Tonight I had just stopped at the bank to deposit a check, hopped in the truck and started her up (started great with no problem), drove the truck through the shopping center and was about to turn on the main road when she died. I coasted into a parking spot and tried to restart her... But all I get is cranking, no firing up or any signs of trying to fire up. Any thoughts?
View 14 RepliesMy Brothers truck died while driving and won't restart. I am going to be getting IDS on it tomorrow night and just wanted some feedback on things to watch. I am planning to watch FICM sync, ICP pressure, IPR %, FICM voltage, and fuel pressure(not in IDS). Anything else I should watch while testing?
Edit: this truck is a 2005
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 RepliesStarted my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 RepliesMy 01 4x4 F350CCD was having this "issue" where, after leaving it plugged in all night, I would start it up with no problems but then after idling for maybe 15-30 seconds it would just fade out and shut off. The first few times I would hit the key again and it would crank for an extended period but then refire and it would idle normally. Eventually I learned that if I held the idle up at around 1000 I could see the rpm drop slightly after starting but it wouldn't shut off.
About a week ago I started the truck and wasn't paying attention and didn't hold the throttle open and the truck shut off. This time after cranking it (probably way to much) it wouldn't start at all. I changed the fuel filter but that did nothing. I also notice that the tach does move to around 500 or so when cranking. I have not changed the CPS but a new one had been installed in May 2015. The engine is cranking but there is no white smoke or even attempt to fire.
Another "no start" issue... The details:
- 2002 F250 7.3L
- Rosewood stage two single shot injectors (rebuilt 1 week ago).
- DP Tuner
- Brand new OEM IPR
- ICP about two months old (OEM)
- New UVH's installed about a month ago
The issue: After installing the injectors and driving about 30 miles the truck died and will not restart. Had to have it towed home. Thus far, I've unplugged the ICP, switched out the CPS with a known good, replaced the IPR, checked the hpop simply by removing the fill plug on the top of the reservoir and gave it a quick crank - oil definitely came pouring out, removed valve covers and plugs to verify oil in the high pressure rails. Oil dummy gauge climbs after about 5 seconds of cranking and seems to hold.
Hoping it's not an injector failure as I just had these reworked. EDIT: Forgot to mention, not seeing any white smoke while cranking. Fuel bowl, full of fuel and fuel pump was replaced this past spring. What to check next? Tried taking a snapshot from a video to show the readings. The ICP seems low, and when unplugged shoots up the 2500, but still no start.
I was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 RepliesI drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
This is the second time this has happened to me . Truck runs fine shut it off go to re start and it's a no start. I can watch the ficm volts drop to 0 from 48.5. Then it's 0 until it decides it gets power again?
View 8 Replies04 Excursion with 03 motor. I had been getting a no hot restart problem. Now it won't start at all.
FICM 48
rpm around 155-175
ipr goes to 77
icp jumps to 475 and drops back to 400-425
My problem started in Virginia, so I got it started cold and drove all the way home to Indiana without shutting it off. Pretty much been parked since. I've driven it 4-5 times. Now it won't start at all.
I have some LPO problem: I posted it November 2013 [URL] ....
After that I replaced LPO regulator, front cover gasket set, LPO cover (Ford tech said my gearator was fine). I don't think this problem is fixed still
We tried to do a leak down air test. Honestly couldn't hear much of a difference with IPR on vs off. Pulled IPR, found the screen in tact but the plastic pieces that hold it on were all rotted away and broken. I replaced with a brand new IPR to be safe.
I'm not real sure what to look into next. Right now I have both valve covers off and tried to look for a HPO leak in valve covers while cranking. I don't see any oil anywhere coming into the valve train. Shouldn't there be LPO somewhere?
My oil is old now but it was T6 and brand new when this problem first occured. Motorcraft filter but the cap is river city diesel billet cap [URL] ....
Could it be as simple as the oil screen to the HPOP or the check ball in the pump? Can the LPO gauge dropping be related to the no start now? Are there any techs that live in Southern Indiana and want to make some side cash? Last thing I want to do is bring this to the local shop or even worse the dealer. Last time the dealer said they wouldn't touch it because the tuner and EGR delete and the local shop left it sitting for a month and hadn't even touched it.
I have a 2004 f350 6.0 and it makes 550 horsepower and lately when I go to started in the morning it'll start at once everything gets up to temperature if I shut it off it will not start again without starting fluid into the air box if it's warm...
View 2 RepliesMy 6.0 stalls when its warm and it restarts no problem. no codes are given with scan gauge. No changes on icp or ipr when it happens. At idle icp ranges 577 to 737, fmp 47.5 to 48v, ipr 23 to 28, map 14.9, tfc .32. all at idle. all increase when rpm goes up. ive done the d plugs, sct plug ficm replaced 2 yrs ago. done egr delete, need to trouble shoot? Again no codes given...
View 14 Repliesno change, changed stand pipe and dummy plug on driver side, no change and guess what? Now I am stuck on the side of the road waiting to give my last $100 to a tow truck! Engine is hydrolocked, fuel pressure is low, starts off at around 20 and works up to 54 with key on engine off, and that is as much as I know from the side of the road with out my AE. Blew white smoke also. Smelled of unburnt diesel. I think it's linked to my rough running issue. Maybe a bad injector? But every time I did the click test they all passed. Idk, I'm gonna remove the glow plugs and see which hole is loaded and with what. . .
View 14 RepliesI have a 2004 6.0 that has been pissing me off to no end lately. I has a random dying/no start problem. If it idles for ten minutes, it'll die sometimes. And if I drive it and shut it off, it won't restart sometimes. I just drove it three hours on Friday, shut it off and it restarted immediately. Drove it around town all weekend and it started fine every time.
Now driving it home and stopped for fuel 45 minutes in, and it won't start. I have all sensor readings in spec except for I have no ficm sync while cranking. I have about 5k miles on new hpop, injectors, ipr valve, icp sensor, oil rail rebuilds, stand pipes, ficm and engine harness and injector harness. No codes either. If it sits for a couple hours it'll start fine. I've wiggled as many wires as I can and it still won't start. I have rpm while cranking on my edge too. Don't know if that would rule out crank sensor or cam sensor.
2003 with hot no start issues. It starts fine in the morning however will not start again after the engine gets warm, after an hour or so of cooling off it will eventually go. Not sure if I should start with.... Readings below ....
FICM L 13.5v
FICM M 48v koeo and 47 running
IPR 14.7% koeo
IPR 74.6% cranking (no start while hot)
IPR 40% (after cold start while running
ICP 737psi cold start
ICP 1600psi engine running 2k rpm
ICP 360 hot while cranking
It just started to die on him lately. Doesn't matter if he is driving or idling. When it dies doesnt sputter or anything. Won't crank up until next day and if it does start only runs for 5 min or so. Checked ficm 48.5 volts. Ipr while cranking is at 48% icp is about 1200 while cranking. The dash oil pressure or rpm gauge does not move but when I hook up my ids it shows 180 rpm. Changed fuel filters. New oil. Does fill up oil canister if I hold the drane button down. Getting fuel. Thought maybe ipr but thought I would check with you all. Unplugging the icp doesn't work. 03 motor with 180k miles.
View 9 RepliesMy truck ran great when I got to my house that I turned it off and tried turning it on again it wouldn't turn on I check the fuel pump it works I checked the injector if it was getting fuel it was .I'm a stand still, where else to check? What to do?
View 14 Replies6.7 with 19k . Drove about 2 miles and noticed dash lights were flashing and ac was not working correctly . Pulled into garage shut off and truck wouldn't restart, no crank ! All my dash lights were flashing & dash was giving numerous messages.. At least I wasn't on my road trip 2 weeks ago! 3400 mile round trip. Truck was towed to dealer! My 6.0 never left me stranded & I had 3 of them..
View 14 RepliesI have s 2007 f250 superduty with a 6.0. Recently after the engine gets warm I have a problem restarting it. I have to turn the key to the run position until all sounds have stopped then I have to pump the accelerator to get it to start. Sometimes I have to repeat this three or four times before it starts. I have had the fuel pump rebuild and installed two new batteries. What I should be looking at.
View 14 Replies