Ford 6.0L Power Stroke Diesel :: 2004 Same Injectors As 2006?
Feb 11, 2016
I found some 04 injectors for a good price, will the work on my 06?
View 9 Replies
Feb 11, 2016
Advertisement
Ford 6.0L Power Stroke Diesel :: 2004 - Missing When Cold - Swapping Injectors?
I have 1 bad injector well it's missing when it's cold and two others that are "weak" I'm wondering what kind of job it would be to do by myself?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Not Starting / Circuit Low For All 8 Injectors
2004 F250 6.0 and it's a no start. I have a snap on scanner and I did koeo test and it came up as inj circuit low for all 8 inj. I performed "the buzz test " and all inj click. The voltage on the scanner for the ficm is 52 and everything I read say that's more that enough. Where I should look?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 - No Crank / Start - Injectors Are Not Initializing
Powerstroke 6.0 no crank no start... 2004 Excursion. I cannot get any of scanners to connect to get any codes. I have the Autoenginuity Ford Package, scanguage II and another generic scanner. There is power to the diagnostic connector but there is no communication.
I have recently been having issues with rough running cold starts. Codes before this no crank event were 2285 ICP Sensor Low and 0528 fan speed sensor low and one for EGR which has been deleted. Just last weekend I had crank no start. I unplugged the ICP sensor and started and ran. I ordered a new OEM ICP sensor and pigtail and the truck sat until I received them.
Recent Work : I just replaced the ICP sensor and the pig tail. I soldered and heat shrank the wires rather than using the quick connects. I did find that after soldering the pigtail I found two wires shorted on the pigtail. Per the diagram on the 6.0 bible the a/b wires were shorted. I have corrected those. I also noticed that the top of the glow plug control connector has a broken clip. Not sure if there is a connection issue so I have tried to ensure that it is pushed in as far as it will go. I have another module somewhere I'll have to see if I can find it. Replaced glow plugs and harness about 6 months ago.
What have I done:
- Pulled access panel on FICM has 4 posts.
- FICM voltage 48v Key On.
- FICM voltage 46v cranking
Check the diagnostic connector can +/- (pins 6/14) and has resistance 122.1
I've check all the fuses and specifically:
#20 FICM
#22 Engine Control
I found one bad fuse #115 Trailer Tow Charge.
When trying to start Glow Plug light comes on but doesn't go out. The injectors are not initializing and the fuel pump doesn't seem to be running either. I have unplugged sensors ICP, EBP and FSS. Not sure what to test next. I'm considering pulling the ficm harness tomorrow to look for chaffing.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Does Not Start / No Buzzing On Injectors When Key Turned On
I have been having trouble w my 04 I checked all fuses all relays all dash lights work, no buzzing on injectors when key turned on. I checked push pull plug for starter it turns over with direct to battery but still does not start. New computer on fender.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - No Crank Randomly / Injectors Buzzing
I think my starter took a s hit like I said truck randomly doesn't crank all lights on dash come on can hear injectors buzzing turn key nothing. Took wire off passenger's side of truck yellow wire touched to pos post solenoid click no crank. So I had the old lady sit in the drivers seat well I hit the starter with my BMFH started right up could something else cause this or should I just bite the bullet and replace the starter?
View 7 RepliesFord 6.0L Power Stroke Diesel :: Injectors Leaking Despite New Seals?
I have replaced all the injector seals as well as the ball cup seals but when I crank the truck over after a few cranks I see oil bubbling up from the top of all the injectors. When looking at the injectors from the "top" side all looks well but when I use an inspection cam from down below I can see this happening. Any thoughts?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Truck Got 4 New Injectors But Still Running Rough
My Excursion got 4 new injectors a couple weeks ago and when I got it back, it was running rough. My mechanic told me it was going to take about 100 miles for them to break in.
300 miles later and it is still running rough. So I opened the hood, took a look around and saw this wiring harness unplugged. Where it goes? Youtube video shows where the harness is [URL] ......
Also, my truck has been shaking violently at 50 miles per hour, unless I hit tow haul, then it is moved up to 60... I am assuming its connected some how to that wiring harness being disconnected.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - All Injectors Blow Out At The Same Time
2003 F250 6.0. We had our truck completely checked over by a diesel shop, and we spent $ in repairs on our 6.0 in June having a new high pressure oil injection pump put in, 1 new injector, new oil cooler, new EGR cooler, FCIM and a few other odds and ends. We had this done before leaving Michigan to spend 6 months on the road for my husband's job while pulling our 5th wheel. We were on the road for 6 hours, got to the middle of Pennsylvania, and every injector blows out of the engine all at once. One head is cracked, all injectors are burned, brand new oil pressure pump is destroyed, oil is pouring out of the turbo. The mechanic we were towed to says we got bad fuel that caused catastrophic failure and he proceeds to rebuild our engine. 2 injectors were so badly destroyed that they could not be rebuilt. We had the fuel tested by a lab and the lab says the fuel is fine. What would cause such a catastrophic failure like this?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure With Race Tune On Stock Injectors
I have a bit of a quandary with my 6.0 and I'm wondering how it compares to others. If you have a hot or race tune (example: super panty dropper) on your 6.0 with stock injectors, what is the peak high pressure oil that you see at full throttle?
Need to know high pressure oil PSI @ full throttle, year (or better yet which style hpop you have if you know), if your ecu tune is a "race" tune, and if you have any FICM tuning.
Ford 6.0L Power Stroke Diesel :: Replaced Injectors - Missing After 20 Minutes Now Won't Start
I have a 2003 Excursion with the 6.0 power stroke. I recently had a few codes, cylinder 2, 3, and 8 contribution/balance fault. I asked a buddy of mine, and he said I needed new injectors. I replaced them all, properly torqued everything down, and got it running. She ran for 20 minutes before it started missing again. I shut it down, and since then it hasn't started. That was two Sundays ago. Since then, I've replaced the ficm, all fuses related to the ficm and fuel pump, and even went in and checked all the connectors. Everything is in place, but it still won't run.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2016 F350 - Metal Shavings Clogged One Of The Injectors
I have a 2016 F350 disel with 2500 miles. It's at the dealer now they are telling me some metal shavings clogged one of the injectors. What should I be looking for?
View 14 RepliesFord 6.0L Power Stroke Diesel :: New Injectors - Now Truck Takes Almost Two Seconds Of Cranking To Start Engine
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
Ford 6.7L Power Stroke Diesel :: 2011 - Glow Plug Dropped And Destroyed The Engine And Injectors?
So bummed. I love Ford but this has put a bad taste in my mouth. Glow Plug dropped and destroyed the engine and injectors. Now i have a bill for 15k for a long block and injectors.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Engine Codes Coming Up After Replacing O-Rings And Copper Washer On Injectors
I removed the 4 injectors on the drivers side of my 2006 6.0 to clean them up and replace the o-rings and copper compression washer. When I put it all together (everything torqued per shop manual) I am now getting P0266,P0291, and P1000 codes. I have checked the connection on the #2 injector, it is good, and I didn't have any problems with connectors breaking or going back together on the FICM...
The truck will start after a long crank,but smokes and runs rough. It was running without codes before I messed with it. The reason for tearing into It was it has experiencing a pretty big drop in fuel milage. I had been running revx and fuel additives with mixed results...
Ford 6.0L Power Stroke Diesel :: Long Start - HOP Would Fire Injectors And Start Up After Several Tries
Had long start issues. Would turn over for 5 seconds - shut off- turn over for 5 seconds - shut off - third try on 4-5 seconds the low oil pressure would come up and HOP would fire injectors and start up.
Was not sure what was up, so look it to Ford. They did leak down test and found seal at the top of injector 4 was leaking. Replaced it and leak moved to other injector. Basically moving to the next weakest seal point. I told them to stop as i did not want to pay, parts, labour and shop time to replace all injectors, etc. They also said power across all injectors was good, but 3 & 7 were not contributing on cold start.
I drove it home and bought parts. New cups and seal for all 8 on fuel rail. New gasket kits for injectors. Plus 2 new injectors to replace 3 and 7.
Replaced injectors in 3 & 7 with the 2 remanufactured i bought. Replaced all cups and seals on fuel rails. So it has new injectors in 3, 4 & 7.
As for the other injectors i took the 5 of them right apart and cleaned them and re-assembled. Took about an hour per injector, took my time to get it right, just FYI. Went pretty good i thought. Seemed pretty straight forward actually.
Now no start - no high oil pressure at all. LOP comes up right away. Scanner shows no HOP no matter how long i crank it.
FICM power good, 47.5 - 48
shows FICM sync - YES
IPR sits at 14% and jumps to 84% on crank - starting, see photos below.
Scanner prior to crank
Scan during crank
Note zero IPC - PSI
Right now.... Got the valve cover off on passenger side. Cannot see oil squirting out the sides of any injectors, but line of sight is limited. Maybe need a small mirror to see in there. LOP comes up better than it has in years, but no HOP now. Before rebuild it seemed i had good HOP but low LOP.
I drove it home from Ford and into my garage, so i do not believe the HPOP crapped out sitting in the garage, so i am ruling that out as a fail, at this time.
Dummy plugs were replaced 5 years ago and o-rings looked decent.
Pulled the small plug screw at the top of the fuel rail. Cranked it until oil came out, bleeding air. then replaced the screw plug. Have not done that on drivers sideyet. Will try that tomorrow. However, think this is more than an air issue, as i have cranked it over plenty, unless i just have that much air.
Going to pull the valve cover on the Driver's side tomorrow. Then will have both covers off at same time to view all.
Noted that if i put compressed air into the screw hole on top of the fuel rail, i can hear air coming out from below the fuel rail. Nothing at the base or around injectors. Does not seem to be at the cups either.
Just wondering.... Buy applying air to those screw plug holes, is that the same as doing the air test at the sensor that pokes up through the valve cover.
With air pressure at these scew plugs on the fuel rail, should this be sealed and be air tight and hear no air leakage. Because it was not air tight on the drivers side before i closed that side up. I am curious about this.
I am assuming i still have a HOP leak. I do not think i have a failed HPOP. How to better chase a HOP leak?
Ford 7.3L Power Stroke (1999-2003) :: Low On Power / Injectors HPOP Or Tune?
So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.
16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC
Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?
Ford 6.0L Power Stroke Diesel :: 2006 F350 - White Smoke / Diesel Drip From Muffler / Poor MPG
I would like the hear what others have to say about the problems I'm having with my 2006 F-350 sd xlt 6.0 with 113,000 miles on it. It's being used as a tool truck mostly going from a shop on the property to close by buildings on the same property. In other words very short distances. Used occasionally to take a dump trailer to a close by dumping ground.
1. White smoke from exhaust. I've read this is most likely an ERG cooler that needs replacing. Any other possible causes? If I end up having to replace the cooler is there a stock cooler that is reliable or should I get the one by bullet proof?
2. Diesel is dripping from the muffler weep hole. Last full tank lasted only 60 miles. Could this be the oil cooler? Anything else? If so is the Ford replacement cooler OK or should I go with an upgraded cooler?
Ford 7.3L Power Stroke (1999-2003) :: Won't Start - Bad Injectors - Coolant In The Oil?
So we begin w/ another saga for the 7.3l Excursion......
A few months ago it started running like crap, real crap and blowing white smoke like crazy. Well I knew this from a previous episode and I had a bad or multiple bad injectors. I tried to trouble shoot which one it was and maybe just replace the one or two....but no it was worse than that. So Life was really busy it kinda got shoved aside until now.
I pulled all the injectors and had them rebuilt locally ..nice. They ended up being with mech for a couple of weeks because he went out of town...no problem. Well this entire time my rig was untouched and when I got them back #7 was full of water.....great, bad injector cup. #7 was the only one, the rest were dry. So I drained the radiator and the oil and left it overnight to completely drain and installed the new injector cup in #7. Next day I refilled via both heads because the valve covers were off, 4 gallons of oil and a new oil filter. Cleared the cylinders via the glow plugs and commenced to trying to get her started. Nada......just cranks, killed the batteries, recharged over night and left the box on them and still nada....but the oil was still very milky at this point.
So tonight I pulled all the injectors back out and drained the oil again, still a lot of water. This time I sucked out the HPOP reservoir and got a more milky water/oil out and I'm leaving everything open all night.
In the am I plan to check my overflow water level in the hopes it remains at the same level...if so I will reinstall all 8 injectors and refill the motor w/ 4 gallons of fresh oil and try again.
Oh, while I was attempting get her started I put my buddies Snapon scan tool on it and I got the p1271-p1278 codes w/ the buzz test. (low side to high side open circuit between idm and injector) So I found the pin test with everything connected at the idm pigtail and everything tested good. So I'm back to my not so fresh oil anymore is the culprit to it not starting.
Am I missing something here?
Also....another fun filled fact is that I seem to have a fuel leak somewhere at the rear passenger side. Every time my fuel bowl fills up, if I shut the key off it will drain down. Sometimes I can see fuel dripping quite vigorously onto my starter but I can not see where it is coming from. I have while it was dripping ran my hand along the head and the fuel lines and can not find where it is coming from. Any thoughts as to where in the hell this fuel could be leaking from?
Ford 7.3L Power Stroke (1999-2003) :: Injectors Barely Spitting Oil
This is a 1999 with 200k on it. It has a really bad hpop so valley is full of oil. Haven't removed the HPOP to inspect the non serviceable plug or the hpop gasket. doing that this week. This truck I just bought and it has aftermarket injectors so dont know the miles in injectors. once the oil leak is resolved I can then give the injectors the once over to make sure theyre okay. Question is how much of a stream of oil should I expect to see as the engine runs?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: New Injectors - Crank But Won't Start - Low ICP?
So I got all 8 injectors upgraded and excited when I get them back I put them all in in kind of a rush. And in that rush I left the cylinders full of excess oil. So obviously when I tried to start it hydro locked. Angry at myself. I kept trying to crank hoping it would fire and just shoot that oil out. Nope, so I went back to taking all the glow plugs out and firing it all back out. Put it all back together then tried to fire her up. Took a minute but she started and I let it run for a while. Hit the gas a few times and then it died. Couldn't get it started again. It would just crank, I checked the icp and ipr and the icp did not build above 35 psi and the ipr was at 98.04% so I just figured the o rings blew out when it hydro locked.
So I took it all back apart put new o rings on, took my time and put it back together right double checking everything. Got it all back together and went to start it, it would just crank around 160-170 rpms, battery voltage at 10.6 icp built up to 140 but now it won't build past 40. Ipr still goes to 98.04. The engine ran just fine prior to injector change, I put a new upgraded hpop prior to injector change, new ipr, icp, cps. Everything checks out, but it will not build oil pressure while crank I've killed a set of batteries then went all out and spent 350 at napa for some optima red tops. I did notice the cylinder 7 injector is the AE injector. It suppose to be in cylinder 8, idk if that's affect the oil pressure building up?
But as far as I know, I'm not building oil pressure. So idk if the hydro lock could have ruined something to keep it from building oil pressure?