Ford 6.0L Power Stroke Diesel :: 2004 - Fuel Pressure Gauge Is Reading Dead 0
Jan 7, 2016
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 Replies
Advertisement
I finally received all the parts needed for installing my fuel pressure gauge, but I am wondering if I am going to need a schrader valve on my fuel pressure line going to the sending unit, or if I am going to be safe with just doing a 6 time cycle of the fuel pump like we do when we change out the fuel filters. Seems like that should work for getting the air out of the fuel lines, same concept I would think.
View 14 Replies
Well, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
View 5 Replies
Couple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 Replies
OK so 2006 f550 6.0
If I want to monitor fuel pressure with a gauge in cab while running all the time... (not just testing) can I purchase one of the secondary fuel filter caps that have a port in the top and connect the sensor to this to run or is there a better way? (Or is that not going to work)
Cap I am talking about is something like this
[URL]
(I know this is a combo kit but they do sell the fuel only) But since it has a threaded port in the top I could connect the fuel pressure sensor to that and go from there correct? Would that give accurate readings?
View 4 Replies
The backlight for my fuel level and oil pressure dash gauges are out. Would that require a simple bulb replacement or if there is something more difficult to replace, i.e. entire panel? The red needles illuminate, it's just the gauges themselves that are dark. The truck is my 05 Super Duty in the siggy.
View 3 Replies
I've had an ongoing issue with my fuel gauge reading incorrectly, and now I'm trying to fix it! Basically, it will change all over the place while I'm driving (not erratically, but definitely moves occasionally). I recently fixed my overhead display, but the "miles to empty" display doesn't seem to be very consistent. It will read 450 miles to empty, and then the next time I look at it, it will have dropped 100 miles or something (after minimal driving).
So I'm wondering where I need to begin looking to fix this problem. I've replaced the dash cluster using Circuit Board Medics, so I'm fairly confident that's not the issue. I've read that it can be the fuel pump or the fuel tank sender, but how to check if these are actually the problem or how much time it will take. Luckily, I've never run out of fuel and been stranded, but I need to fix this or it's only a matter of time!
View 8 Replies
I tried searching here for a pid to get oil pressure. Can't find it. Is it possible to get oil pressure readings on these motors? I assumed it would be because we have a dummy oil pressure gauge on the dash. I thought it would be in the pop up list of gauges on Torque but I didn't see it.
View 6 Replies
I have a 2003 Excursion 6.0. I didn't post this in the 6.0 section because it may not be just a 6.0 issue. (See what I get) On cold starts, anything under 150 degree water temp reading on the SGII. I get a CHECK GAGE light on accompanied by the check engine light. No codes read on the SGII pending or stored. Just some of the time I get a water in fuel light too. This tends to go out fairly soon after driving. (Even after I just drain the fuel pump it still happens.) other issues that accompany the lights are as follows.
The trans temp does not give a reading to the dash. The oil temp does not give a reading the dash. Both show proper temp on the SGII. When in reverse the back up alarm beeps as if something is behind me. And the auto door locks will not activate after 10 mph. The tach also will not show a reading in the dash. SGII shows the numbers. Now the kicker, this ALL gets resolved the instant the water temp hits 150 degrees. The only lingering issue is the that the tach will surge or drop every now and then. The tow/haul light does not come on when this is going on. I've checked the battery terminals all are clean. Both batteries are brand new.
View 9 Replies
Last week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
View 9 Replies
For the second time in 6 weeks My 2004 F250 Powerstroke has run out of fuel with the gauge showing a 1/4 tank. First time it was just under a 1/4 showing I had it towed to dealer and they told me it had sucked in the filters requiring replace and flush of system. The told me that this happening very often and I would be replacing all of the injectors at my cost. I told them that I didn't want this to happen again and to check out the fuel gauge and sending unit and replace if in doubt. Well they checked it out and found nothing wrong, told me it was accurate and should not be an issue again. Now 6 weeks later on the Friday night before a holiday, it did it again, this time with over a 1/4 tank showing. I really don't want to spend 6 grand replacing injectors and would really like to trust my truck again, getting to the point that I'm nervous at 1/2 tank.
View 9 Replies
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 Replies
So, I just had the fuel pump replaced on my '15 6.7 a month ago and it just died again. (next day edit: it didn't actually die, it showed all the same symptoms)
Same symptoms: whining sound, low fuel pressure warning, reduced power warning.
This time I'm 50 miles from home so I pulled off the road before it shut off. Interesting, I was in a hilly area and my low fuel warning came on too. We are waiting for a tow. I was considering trying to push on but don't want to get stuck in a dangerous spot on the highway. We're in a church parking lot.
So, last time this happened I was on flat road with about a half tank of fuel on a lunch break. I ran a mile after the warnings came on to feel out the issue and to see what would happen. I happened to be only about a mile away from my dealer so I drove that way. I got reduced power warning and then it cut power on me (limp mode). I made it to about 100 yards away before it cut off.
This time, I was in a hilly area at night on a windy two lane road with no shoulders in the woods. I was miles from civilization and was showing below a quarter tank of fuel. ~100 miles to EMPTY. I got the low fuel pressure warning first and then the reduced power mode before the whining noise started. I was climbing a hill on a curve at the time. I drove a quarter mile and then pulled off the road into a parking lot so I wouldn't be stuck on the shoulder. It didn't actually go into limp mode.
I let it sit a few minutes, talked it over with the wife and decided to call for a tow. After talking to the tow truck driver who said he would be an hour because he had to go find a bigger truck, I decided to see what I could do while I wait. I fired it back up and the fuel level dropped to below 1/8 and I was now showing 33 miles to EMPTY. I was parked on a hill with the back end up. I had backed the truck into a space to make it easier for the tow truck driver. I let it run a minute, checked for leaks and it seemed to run fine with no studdering or additional warning lights.
CEL was on but no new warnings. I put in my code reader and pulled the P0087. Just one code. I revved it a bit to see if there were any issues. It seemed fine so I decided to try my luck. I started driving towards home with the intention to stop at the first diesel station to fill up. Truck ran fine. After two minutes of driving gently, heart racing, my fuel level came back up and it now read 88 miles to EMPTY. I drove 11 miles to the nearest station and filled up. No issues. I shut it down. I fired it back up. Still no issues so with a full tank, I drove home the remaining 30 miles without issue.
Planning to take it in to the dealer Monday to get it checked. Could this be from an air pocked due to low fuel level and hilly terrain? Is my new pump dying already? Is there something else going on inside the tank or elsewhere?
View 14 Replies
I have my aux fuel tank pump hooked to upfitter 3. It has worked perfectly until this week. I started to transfer fuel and the aux fuel gauge and fuel pump both quit. The led on upfitter switch 3 still illuminates, but no fuel pump. I found fuse 9 on passengers kick panel is for upfitter 3. The fuse was good. Is there another fuse somewhere for the circuit I've missed? I can trouble shoot the wiring if necessary, but it's tough to do all behind the left side underbed box and not easy to get to. I've missed something simple before I go further????
View 14 Replies
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
View 8 Replies
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 Replies
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 Replies
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 Replies
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 Replies
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
View 11 Replies
