Ford 6.0L Power Stroke Diesel :: 2004 F350 No Longer Accelerate / Completely Dies Going Uphill / Will Not Restart
Nov 13, 2014
I have a late model 2004 F-350 6.0 powerstroke. 182K miles. Auto Transmission
What happened. Condensed version
Left house, drove out to highway, got on highway. Everything feels normal.
About 1 mile of going 70mph, I notice I can no longer accelerate. after 1/2 mile, I begin loosing speed, and engine will not rev past 1000 rpm. I eventually pull over (another mile), put in neutral and will not rev past 1000. put in drive and start to idle to highway exit. it gets about another .5 mile and begin going up a hill when it completely dies. Will not restart.
No prior issues with the truck. Full tank of fuel.
What I have tested so far. Ficm 48.5 volts cranking. Icp .225V KOEO, .875V Cranking. LPOP is registering pressure on the dash. No Fault codes.
I have gotten it to start twice now, one time it allowed me to rev to 750 rpm, where i used 4 low to make it onto a trailer. second time would not rev at all. idling at 250-300 rpm.
That same night as it died, I drained the transmission pan/ TP filter and filled with 8.5 Quarts of Mercon LV. This is the first time I have done this since purchasing @ 161K miles. Everything seemed normal, no leaks present.
Also my buddy showed me how to enter the dash test mode and we cycled through these. Not sure if this is relevant.
So, What do I test next? I don't think its HPOP issue since the ICP is reading .875 volts at crank. I did unplug the ICP and it still would not start. I don't think its the injector side of the ficm because they buzz as normal with koeo, but this is a possibility as I don't have equipment to test. Egr valve is clean for age of truck.
Would it be possible that the Mercon LV knocked crud loose in the transmission causing it to fail/seize? would siezed tranny cause the engine to behave in this manner?
Fuel bowl on top of the engine was full of fuel. I have not pressure tested it yet as I can hear the pump running during key on.
could i have a bad crank or cam sensor?
Multi-injector failure?
Bad Icp with HPO failure?
View 14 Replies
Advertisement
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
View 2 Replies
It just started to die on him lately. Doesn't matter if he is driving or idling. When it dies doesnt sputter or anything. Won't crank up until next day and if it does start only runs for 5 min or so. Checked ficm 48.5 volts. Ipr while cranking is at 48% icp is about 1200 while cranking. The dash oil pressure or rpm gauge does not move but when I hook up my ids it shows 180 rpm. Changed fuel filters. New oil. Does fill up oil canister if I hold the drane button down. Getting fuel. Thought maybe ipr but thought I would check with you all. Unplugging the icp doesn't work. 03 motor with 180k miles.
View 9 Replies
My truck ran great when I got to my house that I turned it off and tried turning it on again it wouldn't turn on I check the fuel pump it works I checked the injector if it was getting fuel it was .I'm a stand still, where else to check? What to do?
View 14 Replies
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
View 3 Replies
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
Lately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .
View 7 Replies
I have a 2005 f350 king ranch,I have a kinda weird problem.the truck starts up and runs great as long as I let it get to normal temp.but if the motor is cold it will idle fine but if I goto put it in gear it just dies.sounds like tc is locking but I don't get any codes.
View 9 Replies
04 Excursion with 03 motor. I had been getting a no hot restart problem. Now it won't start at all.
FICM 48
rpm around 155-175
ipr goes to 77
icp jumps to 475 and drops back to 400-425
My problem started in Virginia, so I got it started cold and drove all the way home to Indiana without shutting it off. Pretty much been parked since. I've driven it 4-5 times. Now it won't start at all.
I have some LPO problem: I posted it November 2013 [URL] ....
After that I replaced LPO regulator, front cover gasket set, LPO cover (Ford tech said my gearator was fine). I don't think this problem is fixed still
We tried to do a leak down air test. Honestly couldn't hear much of a difference with IPR on vs off. Pulled IPR, found the screen in tact but the plastic pieces that hold it on were all rotted away and broken. I replaced with a brand new IPR to be safe.
I'm not real sure what to look into next. Right now I have both valve covers off and tried to look for a HPO leak in valve covers while cranking. I don't see any oil anywhere coming into the valve train. Shouldn't there be LPO somewhere?
My oil is old now but it was T6 and brand new when this problem first occured. Motorcraft filter but the cap is river city diesel billet cap [URL] ....
Could it be as simple as the oil screen to the HPOP or the check ball in the pump? Can the LPO gauge dropping be related to the no start now? Are there any techs that live in Southern Indiana and want to make some side cash? Last thing I want to do is bring this to the local shop or even worse the dealer. Last time the dealer said they wouldn't touch it because the tuner and EGR delete and the local shop left it sitting for a month and hadn't even touched it.
View 14 Replies
I have a 2004 f350 6.0 and it makes 550 horsepower and lately when I go to started in the morning it'll start at once everything gets up to temperature if I shut it off it will not start again without starting fluid into the air box if it's warm...
View 2 Replies
I have a 2004 6.0 that has been pissing me off to no end lately. I has a random dying/no start problem. If it idles for ten minutes, it'll die sometimes. And if I drive it and shut it off, it won't restart sometimes. I just drove it three hours on Friday, shut it off and it restarted immediately. Drove it around town all weekend and it started fine every time.
Now driving it home and stopped for fuel 45 minutes in, and it won't start. I have all sensor readings in spec except for I have no ficm sync while cranking. I have about 5k miles on new hpop, injectors, ipr valve, icp sensor, oil rail rebuilds, stand pipes, ficm and engine harness and injector harness. No codes either. If it sits for a couple hours it'll start fine. I've wiggled as many wires as I can and it still won't start. I have rpm while cranking on my edge too. Don't know if that would rule out crank sensor or cam sensor.
View 7 Replies
Changed CPS,EBPV sensor and tube,replaced IPR&fuel pressure regulator,batteries 100%,HPOP full,oil level full,fuel in bowl and lift pump runs(have not tested pressure but has good flow).After replacing IPR truck started quickly and idled for 15 minutes,decided to try a test drive ,truck stalled after reversing 10 ft as I shifted into first gear.Now no start!!Losing my mind.
View 4 Replies
Ok, so my 2002 f250 died on me last Tuesday out of the blue, pulled it home and found fuse 23 I think ECU power was blown. I removed my Hydra, and put a new fuse in it and all seemed well, then Friday evening on my way to dinner was driving along and truck shuts off like someone turned the key off. I replace the Crank sensor, even though I had put a new one in after the first time it died, which was last Tuesday, still would not start.
Pulled it home, went out Saturday morning to look at it and hit the key and it fired right off. At this point I don't really know where to look, I wiggled every wire I could find while it was running Saturday and no change, but it does seem to have a miss in it while it is idling...... I am not sure where to start looking....
View 7 Replies
My excursion died while driving down the road I lose everything but once I turn the key off and turn it back on it will start turning over again but don't . I let it set for a few minutes and it will start right back up like nothing every happen . this is our only transportation for now. The recent things I've done is change out the radiator and upper and lower hoses due to a tiny crack in the neck. I also changed out the hose from turbo to pipe on the hot side due to wear out hole.
View 14 Replies
I have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
View 13 Replies
Early 2004 (IPC under turbo) 163000 miles. Injectors done last summer. Stock. Got a call that this guy died on the highway. By the time I got there (45 minutes?), it started and ran fine. He drove it for ahile, shut it down, drove it some more and it died again. I finally got it in and looked it over and test drove it. It died on me twice (Both times, I was pulled over and stopped. How lucky is that?) When it died, it showed that the Desired ICP dropped to zero just before the actual and the ICP voltage did. I wasn't watching the Regulator%. Cranking, it showed about 210 ICP and .19 ICP voltage. After it sat for maybe 10 minutes, it finally started.
Now, my question is, do I have a ICP problem or an electrical problem? My thinking is an electrical problem because to me, it doesn't seem like the oil would cool off enough in 10 minutes to allow it to become thick enough to build pressure again. I also noticed that the ICP dropped down to as low as about 590 at low idle once the oil temp was up to about 190, but it wasn't always that low - usually it was around 625ish. I have it idling right now and recording Sync now, but of course it's running fine. If my sync drops out, I need to change the Cam sensor or crank sensor, correct? If it doesn't drop out, I have a ICP problem. Does that sound right?
View 14 Replies
Have a 2004 6.0 that stalled out while driving. Wouldn't restart. Took readings this morning. ICP was very low (below 100) and IPR was at 85. After a few times of taking readings I could get the truck to start up with an ICP reading over 500 but IPR was still at 85. When it did start up it would almost immediately die. Does this sound like an IPR problem or a oil pressure problem?
View 5 Replies
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
View 14 Replies
I have an 04 f-350 that I did an EGR delete, new Ford oil cooler, new radiator (not ford), new thermostat (not ford), coolant filter, glow plugs and harness, MBRP theoretical 4in downpipe (was 3.5 to converter) flushed cooling system with lots of tap water before the delete, replaced coolant with Cat 1 ELC and distilled water, fresh T6 5W-40 and filter, several weeks ago. Was troubleshooting a wireing problem and found what looks like oil sludge in the degass bottle while under the hood.
Possible that while doing EGR delete I clipped a gasket? Truck runs great, no smoke out the tail pipe. There is what looks like about a cup floating on top the coolant. Oil level is down about a 1/2 quart and clean, no water in it. Where do I start looking?
View 14 Replies
I have a 2004 Ford f 350 superduty. Everything runs great. Now the other day my fan came on and stayed on for three days now. It goes with my rpm so when I am doing a 100 down the highway in hopes it will disengage but won't.. Everything is Stalk.
View 3 Replies
Just tried putting a ts6 on my pcm. First time I hooked it back up I just got cranking with no start. So I pulled the pcm terminals really well plugged it back in and got nothing. I do not remember because I was kind of in a hurry if I unplugged the batter cables and back on the second time. I plugged it back in after cleaning terminals and went to start and got nothing. A loud click on passenger wheel well and then all electric in truck completely dies. I hope I didn't fry my pcm. Maybe just blew a fuse or starter relay?
View 6 Replies
