Ford 6.0L Power Stroke Diesel :: 2004 F250 Losing Power Then Stalled Out And Wouldn't Start
Jul 29, 2016
this morning I started my 2004 f250 drove a mile and filled up my truck. Then drove another mile and my truck acted like it was running out of fuel. It was loosing power then stalled out and wouldn't start. About five hours later I tried to start it again and nothing. about five hours after that I tried it again and it started up and drove fine.
My thought was fuel filter or the water trap. I haven't had a chance to open the filters up and check them yet. Today while I was at work I got on here to see if I could figure out what was wrong with it. all I could think of was maybe the HPOP went out or the ICP sensor. Could one of these be the problem or was I right with my original thinking and it's just a fuel filter? First thing in the morning I'm going to pull the filters and replace them.
Could there be something else wrong with my truck that I don't know about? Like I said I filled up the fuel tank then it lost power within a mile and stalled out and wouldn't start back up. Then about 10 hours later it fires up and acts like nothing happened.
View 6 Replies
Advertisement
2004 f450 with 6.0. Was driving down the road when it started losing power like it was starving for fuel. It carried on for about a mile then died and will not start. No codes at all and we put a new fuel pump on but still wont start. Put a rag with gas in the air box and will run but rough.
View 6 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
I have a 2006 f250 6.0. the truck has 101k miles and to this point I have had zero issues. I am having trouble loosing power after running at highway speeds. Once I stop and begin to accelerate the truck looses power for a few seconds ,Belches smoke and begins to operate normally. I had an egr code, so I replaced egr and the problem persist. It is intermittent and does not happen if I stay under 50 mph.
View 12 Replies
2003 crank no start, 196k bone stock truck egr still in truck and stock head bolts. Replaced the icp sensor and ipr sensor, both from ford. What happened is I got fuel then about 15 minutes afterwards my truck acted like it was going up a hill and was just losing power and shut itself off. ficm tested 48.5 volts all 8 injectors tested good and there is oil pressure. Had an egr fault code but I'm at a loss.....
View 7 Replies
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
View 14 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
I have a 2006 F250 with an International 6.0 turbo diesel. Last Friday I was driving 70mph up hill when my truck slowed down (I wasn't hauling anything) and then stalled, I got it restarted my doing a moving restart. After that it stayed in limp mode and wouldn't go up into 4th gear it just would jump from 1st to 2nd them to 3rd if I was coasting and it would only let me go 40mph at the most, so I got a tester and tested it and the only code it gave me was glow plug 1 & 5 were misfiring so I replaced those.
After I decided to do a test drive I went 800 meters and my tuck still didn't go out of gear one and I couldn't get my truck to go more than 5mph, then it stalled, so after about 30 minutes and 2 other guys tinkering with everything, we got her started and she sounded perfect, so I took off again, same thing happened except I got her going 20 mph but her RPMS stayed under 2,000 and then it decided to sputter and then stalled.
When I went to restart her the ABS, TBC and the transmission light went off, now she won't crank over and she was clicking (starter or dead battery) and now the lights don't go off, the Windows don't work and their is no electricity flowing...... I understand the electricity, she has 2 batteries. (The first one starts i.e. Glow plugs, starter etc, the other just supplies juice to the system, I.E. Lights, fuel pump.. Etc) what is causing this?
View 6 Replies
I was towing a trailer about 600 miles truck was running great, pulled in for fuel and truck was running rough, refueled and was on my way then when going down a hill (Idle) it just quit, had to tow remaining 200 miles.
After reading the forums I replaced the ICR (ICR screen was damaged) Truck now starts but its very loud and missing like crazy. and surges if i give it a little gas. codes 0268, 0281, 2284, 2288 I also replaced the ICP.
should I replace the injectors? what causes this?
View 14 Replies
I have an 04 6.0. My truck was running perfect, no problems. I start my truck, it started idealing rough for a couple seconds then just died. After that it just kept cranking and no start. There are no codes, tried unplugging the ICP sensor and nothing. Checked the fuel filter and its filling up with fuel before cranking. Oil is at a good level. FICM is reading 46.5-47.5 before cranking. Checked the ICP Psi I'm only building 11psi and HPOP was replaced in October.
View 13 Replies
My husband and I purchased a 2004 f250 king ranch 6.0L... We love the truck, despite the headaches. We took it to a dealership and spent just under $5k in parts, drove it for a month (everything going great) until we shut it off to bs w a friend and it won't turn back on. It's been sitting for 4 days and nothing. Cranks and cranks, but won't actually start. We are pretty handy with gas trucks, but this diesel is out of our element- we are getting better though haha!
We looked on here and saw that the no start could be bc of the FICM - swapped it out- not the issue.
Now the codes being thrown are P2291 & P2285 (or so my husband says)
We are thinking if we replace the ICP and that fixes it, we won't need to do the HPOP. Or do we need to do it as well? Are we on the right track?
When we shut it off, it didn't have any lights on, no gauge fluctuations, or any "red flags". This is why we are stumped!!
(Ford dealership fixes: 2 batteries, new starter, new tank cap, new oil cooler, maybe a few others- receipts not infront of me).
Like I mentioned, we've already dropped more money than we have into this truck and now it's taking more- we love the truck and once it's fixed we will "have a new truck" it just sucks bc my husband works afternoons and I'm a stay at home mom with a 14mo and this is our only vehicle.
View 12 Replies
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
View 4 Replies
The truck is a 2004 f250. Build date is 7/ 03 so its an early 04. I have been in a parking lot for 3 days now with no money trying to get this truck to start. Me and my dad replaced the ipr pigtail and the ipr thinking this might have been the problem, because the ipr pigtail had a damaged connector.
Before doing this work the icp sensor connector had no oil in it, now after replacing the ipr and cranking the engine the icp has some oil in the connector, could this cause a short and not let the truck start, and if so will unplugging the icp allow the truck to start?
We were having trouble with no starts before this happened and when it did all we had to was push the ground wire back further that goes back to the ficm and the truck would start, but that is not working anymore.
Is it possible the ipr is not seated properly or the new ipr is bad out of the box? Or maybe the made in tawain pigtail connector to the ipr is bad?
We are thinking it may be a short somewhere in the harness since everytime we pushed the ground to the ficm up further to where it grounds before when we had no start problems this might have took the short out of the ipr or icp pigtails and allowing the truck to start. Injectors are buzzing when key is turned and I can hear the fuel pump.
View 14 Replies
Fuel injectors do this? They are off a 2006 Ford F350 dually with the 6.0 diesel motor! Have replaced all 8 fuel injectors got back drove for 200miles and fuel injectors 4 and 8 were throwing codes changed them out and high pressure oil pump oil coolant deleted egr valve changed the ipr valve feed tubes to the oil rails. replaced the FICM. Yet again drove for 2 days about 200 miles again and shut down (stalled) misfiring hard start. and now fuel injector 4 is throwing codes again. Have not drove it since we got it home from the last stall out which was a few feet from our drive way and we towed it home.
View 5 Replies
I have been having trouble w my 04 I checked all fuses all relays all dash lights work, no buzzing on injectors when key turned on. I checked push pull plug for starter it turns over with direct to battery but still does not start. New computer on fender.
View 2 Replies
I have a 2004 F-250 changed out both fuel filters and now can't get it to run. It will start up and run for about a minute then stall out. I have cycled the key/pump numerous times with no luck. When I look into the fuel bowl when I engage the pump it looks like it's pushing more air rather than fuel. It seems to be burning the fuel in the bowl and then stalling out. When I take the bowl cap off after it stalls it's empty.
View 14 Replies
I have had literally no issues with my 2004 F250 Super Duty. Went out and started the truck like every other time for the past 13 years. Started backing out of the driveway and burped the throttle and it just quit??
I put back into park and it rolled over for about a minute and finally caught. When i put it back into gear i had zero throttle response. I have a NOx sensor fault code and and EGR fault code. I replaced the FICM 2 years ago.
View 3 Replies
So I recently bought a '04 F-250 early build with the 6.0 powerstroke. Truck drove fine for the first 1000 miles. Drove from Fort Hood back home for leave. Got home and truck sat for two days, started it up and it ran for 15 minutes, then shut off on me. Temp gauge read normal, but after it shut off, I turned the key off and back on and temp gauge was maxed out. And truck has to cool down before it will start again. Replaced the IPR Sensor to no luck. Not sure if I have an ICP sensor issue or what it could be.
View 11 Replies
Have a 2004 6.0 that stalled out while driving. Wouldn't restart. Took readings this morning. ICP was very low (below 100) and IPR was at 85. After a few times of taking readings I could get the truck to start up with an ICP reading over 500 but IPR was still at 85. When it did start up it would almost immediately die. Does this sound like an IPR problem or a oil pressure problem?
View 5 Replies
2004 F250 Powerstroke Diesel 6.0L ... 90,xxx miles
Symptoms : Within the past 10,000 miles the truck has begun exhibiting the following problems, sometimes in conjunction with one another and sometimes just independently of one another:Stalling on the road at low speed / low engine RPM.
Throttle pedal becomes completely unresponsive. Stabbing the throttle pedal repeatedly sometimes causes it to return to operation. Sometimes the engine must be shut off and re-started to return throttle pedal to operation.
Rough, surging, stumbling idle at rest. Will crank but not fire occasionally. Problem has become worse as of late. Repeated attempts at starting the engine usually result in success after much, much retrying.
Work Done : Local Ford Diesel technician replaced the EBP sensor, replaced the EGR valve and re-flashed computer with latest software -- all under warranty. Problems still persist.
Peculiarities : We have tried driving the truck with the EGR valve disconnected and with it connected, both at the technician's request.
With the EGR valve disconnected the truck usually starts fine but still stalls out at low RPM / low speed. Fuel economy is also cut by nearly 50% with the EGR valve disconnected. Really couldn't afford to keep driving the truck like this.
Technician speculated that if the truck continued to die with the EGR valve unplugged, it meant that the computer or fuel pump might be bad. ????
It also seems that the stalling problem manifests after the truck has been driven at highway speeds (65-70mph) for at least a period of 20-30 minutes. Stalling usually happens as soon as we make an exit off of the highway and begin to slow down to make exit. As in foot off the throttle pedal. Engine RPM drops then stumbles then stalls.
I wonder if this is a problem with the HPOP or ICP system.
Specifically I wonder if this is a cracked quick release fitting that allows oil pressure to fall after the engine heats up and oil viscosity thins out with the heat. Once the engine cools down sufficiently to thicken the oil, the HPOP finally gets enough oil pressure to allow the engine to fire up again.
View 14 Replies
I have a 2003 Ford F-350 super duty 6.0. A few weeks ago it starting loosing power, it wouldn't even go up to 15 mph. It now won't even move. There is 0 power. When I press the gas the motor bogs down to a very low idle and wants to die. I also had recent trouble with it starting. It would wind up to a very very low idle and about a minute later it would crank up to full idle. I changed the fuel filters (on top of the engine and under the cab) and also changed the fuel pump under the cab. After that I still have no power when pressing the gas it will still act like it wants to die.
View 14 Replies
