Ford 6.0L Power Stroke Diesel :: 2004 F250 - Transmission Stuck While Warm Up?
Jan 27, 2017
I have a 2004 F250 I just had a Ford transmission out in it. when the truck is cold it runs great. buy when it gets warm it gets stuck in a gear, even if I drop it into a lower gear. Also, if I cut it off when this happens and i cut it off it will not turn over as if it's not in gear, in park or neutral, but if I let it sit for about 20 minutes it will turn over and run as it should until it warms up again.
View 1 Replies
Advertisement
I have s 2007 f250 superduty with a 6.0. Recently after the engine gets warm I have a problem restarting it. I have to turn the key to the run position until all sounds have stopped then I have to pump the accelerator to get it to start. Sometimes I have to repeat this three or four times before it starts. I have had the fuel pump rebuild and installed two new batteries. What I should be looking at.
View 14 Replies
When the truck shifts into 5th gear i instantly feel a constant vibration and noise until it shifts to 6th gear. This happens nearly every time while driving at 40mph. Rpm range 1200 - 2000. I bought the truck new on June 30th and noticed the problem on my way to work on Monday July 2nd. Took it to the dealer on July 5th and the tech said it was the torque converter slipping. I drove it home because they didn't have time to work on it. Took it back on July 12th and the dealer has had it since (currently 30 days) They originally told me it was not the engine or transmission and it was an exhaust problem. Last week they said it was the motor mounts and said they would be done.
View 14 Replies
Transmission was not shifting out of second gear set a code stuck solenoid cleared code seems to be working now....
View 4 Replies
My 2012 F250 6.7 once again (third time in 2k miles) got stuck in park with no brake lights or traction control. I found that removing the shroud from the steering wheel allowed me to manually activate the solenoid and get into gear but could only drive in manual shift mode.
Something is causing the brake switch fuse to blow. When I replace the fuse all is well for maybe 1k miles then it happens again! After the second time I replaced the brake switch thinking it was the cause but no deal. It happened a third time. The dealer who fixed it the first time could not find the cause.
This is frustrating and downright dangerous! What in the circuit could be causing the short?
View 14 Replies
I have an 04 F-250 6.0l Power stroke diesel with a problem. The engine starts fine and runs normally until it gets warmed up. Once it is at the normal operating temperature it starts to sound like it is misfiring when idle. Once I accelerate it sounds normal again but when I slow to idle the misfire comes back.
View 5 Replies
2015 F250 with 6r140 Transmission. I have 13 K miles on my truck. While pulling my Travel trailer up a hill the transmission kicks down thru the gears, which is fine, but as I crest the hill and in 2nd gear, the engine begins to rev up and the speed increases, the transmission will not automatically go into 3rd gear. I have tried to let up on the gas pedal, but it remains stuck in 2nd gear. I have to shift to manual and then put it in 3rd gear. Then it shifts up as it should. I have tried with the transmission in "TOW' and not in "TOW". I have even tried it in "Cruise Control". Ford dealership ran tests but could find no problem. However it was road tested without the trailer.
View 5 Replies
My 04 6.0h started puffing bluish colored smoke typically only when I was accelerating. After a short amount of time I noticed it was smoking quite a bit when cold and until it had fully warmed up. I took it to the repair shop and they pulled it apart saying the turbo seal had failed and the turbo was full of oil. I purchased a new Garret PowerMax and had it put it in.
I picked up my truck and of course it was still smoking when cold. After it warmed up nothing, just like before. Since I just put a new turbo in I am worried this one will be ruined as well since the same condition exist. My mechanic said I need to run the truck for few days before the oil would get cleared out which had accumulated in the system. Am I mistaken in thinking that if it was residual oil burning that it would be more likely to do smoke when warm as opposed to when cold?
Since the turbo and seal have now been replaced what else should I look for to cure my blue smoke blues?
View 2 Replies
I have a 2006 f250 6.0L with 76,000 miles on it. And it just started to shift softer then normal under light throttle. The first to second to third shift are softer then normal. And the third to fifth gear shift seems to have a lot of what I would call overlap and some times it feels like it is slipping. Gets better under hard acceleration but not as firm as it used to be. I have always changed the trans fluid and filter every 25,000 miles. Trans temp runs about 150 to 160deg. I checked the fluid today and it's bright red and does not smell bad. And I don't have any coeds. Could it be a solenoid going bad ?
View 9 Replies
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
View 14 Replies
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
View 5 Replies
I have late 2004 with 130k with a bpd egr cooler and new oil cooler and new ficm from Ed. Cat delete with no muffler. Everything else is stock I have a dash boss and was noticing some weird numbers. My check engine light came on but I couldn't get any codes with the dashboss. I started monitoring the egr error and saw some erratic readings really high negative numbers after I let the throttle off. The truck runs okay but was kinda starting slow. Could my egr valve be stuck? Could my short modified exhaust be messing things up?
View 7 Replies
I picked up a 2016 F250 Powerstroke in the first of March. I owned a 2011 before and loved it.
The 2016 has been great so far, but I've noticed a sound that wasn't present in my 2011.
When the transmission is warmed up, I get a "cla-click" sound from the transmission area when sifting from park to reverse. It doesn't do it all the time and I can only hear it, not "feel" it.
This AM I heard a similar click sound when I came to a complete stop. I only heard it while stopping, not while taking off. I could repeat it almost every time I stopped. I was in drive the whole time I heard the click sound while stopping.
What it may be? I know sounds are one of the hardest things to communicate/diagnose.
View 6 Replies
I have a 2004 F250. Owned it for a little less than 4 miles (186k on the odometer) .. The other day making a routine run and the radio goes out. Stopped to check it out and found I had no power windows either.
Made it home, checked the fuse on the radio and its good and the the power window fuse is also good. Put a meter on the terminals and have no voltage going to them. What I need to look at???
View 11 Replies
I have a 2004 F250 6.0 DuperDuty with about 170,000 miles on it, so far no major break-downs, just a starter and a blinker relay, but now I have a problem.
When I start now, the truck starts fine and it sounds fine, but it has almost no power even if I floor the gas peddle, there is a delay of like 2-3 seconds and then responds slowly, like some tractor. Eventually it starts to move slowly, and after it warms up (after a few minutes), the gas peddle responds more normal.
Also - at about 45mpg, at lower RPMs about 1250, the engine starts to shake (weird), it doesn't do it at idle about 850 RPM, or when I get it up to about 1800RPM+, but at about that 1250 RPM it does do it, luckily I driver locally for a few miles.
What could this be ? What exactly happens when I press on the gas peddle, what systems are involved and in which order?
View 14 Replies
I've got a 2004 F250, 6.0, with 150k miles. I was pulling a motorcycle trailer uphill in the mountains when suddenly I couldn't go over 10 to 15 mph. All the gauges read good but it just couldn't get any power.
Got to the top and checked over everything. Didn't see any issues. Drove it home (200 miles) the next day. It drove okay on highway but it felt like the turbo wasn't coming on. Coolant was low and EGR was gunked up but only slightly wet. From what I read, it sounds like EGR cooler is failing but would that cause the turbo not to come on or feel like that loss of power? Reading another thread, I thought it might be the fuel pickup but I dropped the tank and the sending unit looked very good.
I'm ready to throw on a bulletproof egr cooler, oil cooler and rebuild the turbo if necessary but hate to get to the end and find out none of that worked.
View 5 Replies
I have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
View 13 Replies
First off my vents stopped blowing completely. At this time the thermostat was still functioning. Fuse 28 was blown. I replaced the fuse and it blew again shortly after turning the heater on. I replaced the relay and resistor and still blowing fuses. For some reason I tried a 30A fuse and it didn't blow but a few minutes after turning on the heater there was a burning smell. I immediately turned it off and pulled the fuse back out, which was hot. I then replaced the blower motor and at this point there is no power at all to the control panel. The fuses are all fine as well as the relay and resistor. There's power to the fuses. So it seems like somewhere between the fuse box and the control panel I'm losing power.
View 7 Replies
While driving home the other night at highway speed my truck lost power. I just filled the tank about 15 miles before then and everything was running fine. No lights came on the dash before the truck died and now can't get it started. Bad fuel? Clogged filter?
View 5 Replies
this morning I started my 2004 f250 drove a mile and filled up my truck. Then drove another mile and my truck acted like it was running out of fuel. It was loosing power then stalled out and wouldn't start. About five hours later I tried to start it again and nothing. about five hours after that I tried it again and it started up and drove fine.
My thought was fuel filter or the water trap. I haven't had a chance to open the filters up and check them yet. Today while I was at work I got on here to see if I could figure out what was wrong with it. all I could think of was maybe the HPOP went out or the ICP sensor. Could one of these be the problem or was I right with my original thinking and it's just a fuel filter? First thing in the morning I'm going to pull the filters and replace them.
Could there be something else wrong with my truck that I don't know about? Like I said I filled up the fuel tank then it lost power within a mile and stalled out and wouldn't start back up. Then about 10 hours later it fires up and acts like nothing happened.
View 6 Replies
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
View 13 Replies
