Ford 6.0L Power Stroke Diesel :: 2004 Excursion Gargling On Initial Startup
Jul 17, 2015
When I start my truck up initially and it's somewhat cold, like even if it hasn't run for just a few hours, it seems to gargle when I get on it. I'm not slamming it while it's cold but even just trying to accelerate. Code is egr flow insufficient, the truck isn't egr deleted, I've had it for 150,000 it's got 211 now. I just clean out the egr every 15-20k and it's been great until now. Once it warms up it sounds and runs perfect.
View 2 Replies
Advertisement
My 06 6.0 is blowing a fair amount of blueish, whitish smoke only on initial startup, then continues to blow smoke slightly for around 10 min until it's warmed up. It seems to be getting a little worse as time goes on, only on startup though. truck has no other issues otherwise, has an egr delete, and some old edge tuner. I don't think it's head gaskets, no other symptoms.
View 6 Replies
I was pulling a empty trailer and my boost started to act up. it would take a few seconds then I would get boost. my EGRs went up to 1050 and started to spit out black smoke. I got home everything went well after. Next day I went to another town no trailer and it started to sputter going down the highway. When I gassed it and let go it had a loud like gargling sound. But it would sputter and throw out black smoke every time it did it. I finally got to my destination and turned the truck off for about 30 minutes. Left to go back home and the motor ran as if nothing every happened to it. What is it. I have a 2004 F250 stock with new air filter and juice with attitude.
View 4 Replies
What causes elevated engine idle when cold or initial startup? Asking another way, what would cause it not to have the elevated idle on start up?
View 14 Replies
I have a strange issue and it happens very sporadic. Sometime it occurs at startup, sometimes while driving. Not sure whether it is limp mode, but I have no throttle. It starts fine, idles, but no throttle. Like I said, sometimes it happens while driving and I have to pull over and shut it down and restart. Mods are few, it has an airaid air filter and I had the turbo rebuilt and egr delete both completed in May. FICM was rebuilt by ficmrepair.com a couple years ago. It does seem to happen more often when it is raining or with a heavy dew after sitting for many hours. 128k.
I adjusted the pedals all the way out and back in and it stopped for almost 5 weeks, but it has been pretty dry here in SW Ohio. then it got really foggy one day and rained the next and it has started again. Could it be that the EGR pigtail is getting moisture. It does not throw a CEL and my scan gauge II shows no codes. I did run a dose of hotshot's secret thru the fuel back in may, ran a couple tanks of fuel, then changed the filters with OEM. I have had this truck for almost 3 years, but still a newbie when it comes to diesels.
View 14 Replies
I have a 2004 Ex, 6.0 PSD, 4x4. I am experiencing a fuel leak after first startup. Fuel drips off both side of engine area but not coming from the top of the engine, valley is dry. Truck runs great, no hesitation or buffeting as if it was leaking from the intake area. After about 10 min of running leak stops but there is some occasional drips from residue.
This all started after I installed the IPR remote coil cooler and Gen 3 EGR delete. I thought I was smelling an exhaust leak but didn't realize it was actually fuel until just a few days ago when the leak became really bad for about 10 min, leaks about a cup of fuel. I have added a UV due to the tank to see if that will show the leak.
View 14 Replies
2004 f350 4x4 sc dually 130K mi. Cranked truck this morning @ 18*F. Truck not plugged in but regular quick smooth startup. Noticed light blue smoke with normal condensation exhaust for about 5 seconds, then normal condensation exhaust for about 30 seconds. Drove truck at normal operating temps with 5* deltas. To my knowledge, truck has original turbo (Garrett), never been removed or cleaned by me. VGT at startup 70-72, running after warmup mid 50's. Is this a symptom of needing to replace turbo seal, and thorough cleaning while off?
View 1 Replies
Today I decided to do some maintenance on the truck as it needed an oil change and some other unrelated misc stuff.
1. I seafoamed the engine thoroughly. I bought two cans of this stuff, half of a can went into the fuel, another half can in through the brake booster vacuum hose, and I dumped a full can of into the oil. Took it for a 30 minute drive, let the ol' gal smoke as it usually does on a seafoam, and then changed the oil. No noises, I noticed immediately improvement in acceleration.
2. Upon intial startup after the oil change, I thought the motor was coming apart. It was only for about two seconds, (i was counting to make sure) if it didn't have oil pressure and no noise by 3, I was shutting it off. It hasn't done it since.
Is it possible I just knocked some crap loose in the heads causing the oil drain a lot faster into the pan than I expected? I'll try it again in a few hours after everything has cooled off and oil has drained back into the pan, but I wanna make sure I didn't damage anything. Still drives good, no problems, no noises since.
The last oil change I did, I didn't do a Seafoam, but I figured with winter coming it's a good idea to get her running in top form. I used Pennzoil Platinum 5w20, with a Motorcraft oil filter for those wondering.
Truck has 133K on the clock, and it's had the slight cam phaser tick since I've purchased it, no other problems. I bought it almost a year ago.
View 3 Replies
I have a 2008 6.4 powerstoke with 162,000 miles. It went into reduced engine power , so i had a sct x4 tuner with cold air intake and dpf delete installed. i just picked it up and it is smoking at initial start up. Is this somewhat normal...
View 1 Replies
My 2004 Excursion 6.0 4x4 is leaking oil around the gaskets. Does this usually just call for replacing the gaskets and is there anything that needs to be checked or upgraded while the engine is out? It looks like the engine needs to be taken totally out although I have heard it just has to be lifted a little.
View 14 Replies
I've dreaded the day I would receive the Red Triangle. It occurred upon initial start up this morning.Could this be brake system related as 3 weeks ago I got my front brakepads/ rotors replaced. Since then the front brakes have been grabbing to the point that my wife will ask me about the noise when she's in my car.
The hybrid battery indicator is always many blue bars and green with no wild flucuations. I'm getting between 48-51 mpg's. For general maintenance I installed the Optima Yellow top about 4 weeks ago. Oil is full, coolant inverter reservoir is full with tuburlant motion and was replaced under recall 2 years ago. The transaxle fluid was changed 20k miles ago.
So back to the brakes. I have the Red Triangle with !, VSC.
2008 Prius, 184K. Well maintained, 85% highway miles
View 9 Replies
When I first start my excursion in the morning, it starts fine, idles fine. If I don't let it sit for about 5mins plus i have this issue. I will start off and it has no power at all. I can barely get up to 20mph. It doesn't seem to want to change gears, I don't hear the turbo spool up. Then all of a sudden it will go to next gear, turbo spools up and it has power again. It is like I said a 6.0 power stroke, its a 2004 excursion with 214k miles.
View 11 Replies
I have a '94 Chevy Suburban with a driver's side power window problem. The window will work for 5-10 seconds upon initial startup but once I stop and try to restart, the window won't do anything. If I pull up on the window while pressing the window switch it will start working again whereas I can let go of the window and keep the button depressed until I reach the desired level I want the window to be. At times I get nothing up or down by pressing the switch leading me to believe it's the motor. It seems to have the most trouble going up rather than down. I am not sure what the problem is, i.e. regulator, motor, electrical relay.
View 1 Replies
04 excursion 6.0 auto. New batteries a month ago. New alternator (New Bosch) 6 months ago. Charging system shows 12-13 volts on scan gauge with engine off, 14 with engine running. Drops to 10 or 11 while actually engaging starter.
Every once in a while, often when the engine is hot (in fact I can't ever remember this happening when it's cold) the solenoid clicks like it would when the battery is dead. So far, it does this while it's actually engaging the starter, so I hear the solenoid clicking under the hood while I hear the whir of the starter under the floor board.
Never had this happen before. Not sure what part is trying to tell me it's on its way out? Heat soaked starters are harder to start, or less powerful, or something, right?
View 14 Replies
i have a 04 ford excursion 6.0 with the egr delete, was stopped at a light to make a left turn, when i stepped on the accelerator pedal nothing happened as the engine was just idling. i pumped the pedal around 10 times and finally got the engine to rev up. i just got this excursion and don't know to much about the maintenance on it. i am going to drain the water and change the two fuel filters. my neighbor is familiar with diesel engines and he said to look at the throttle sensor. i have run this engine up to 900 miles and it has started and run perfectly. i believe the usual maintenance like oil changes etc were done on it. would any error codes show up even though no warning lights on the dash.
View 8 Replies
I have a 2004 Excursion with a 6.0 Bought the truck already studded, EGR deleted, and a 54V FICM. When I bought the truck it had a hot stall, no restart problem. Found the high pressure oil leaks and resealed them by replacing the #3 injector and replacing the top injector seal in the #4 .Oil pressure reads very good now and I drove the truck for a couple weeks problem free.
Truck started smoking (white to gray) and felt like it had a miss. No misfire or contribution codes. Truck failed the bubble test and I narrowed the leak down to the passenger side by removing the banjo bolt
Banjo bolt at the front of the passenger head
Found the #3 injector loose...the copper washer
Copper washer had disintegrated/melted and appeared to be stuck to the side of the injector. Scraped off easily enough, cleaned up the injector and injector cup and reinstalled the injector with new O-rings and copper washer.
Put the truck back together and still smoked the same and still felt like it had a miss. Ran KOER test and found sometimes a contribution code for #2 and sometimes #6 .
Drove the truck to work and it didn't feel down on power...mostly just smoked and rough idle...but on the way home there was a lack of power and just as I pulled into my driveway the truck stalled...wouldn't restart. FICM voltage was good, high pressure oil read over 900, IPR was holding around 40%.
Pulled the secondary fuel cap
Secondary fuel cap to run another bubble test...there was no fuel in it...completely empty. Started to think that I had a fuel feed problem. Hooked up a fuel pressure gauge
Fuel pressure gauge and drove the truck again...pressure wasn't great (45 lbs) but never dropped below 42...not even when it stalled. Pulled the cap again...dry again...yet the truck read fuel pressure.
Research showed that I was possibly pressurizing the fuel system with combustion pressure and that was possibly displacing the fuel from the fuel system. This would explain the run for a few minutes, then stall and no restart for a few minutes...I'm assuming that the pressure would bleed off and the fuel pump would start over.
Still failing the bubble test and still pointing to the passenger side. I pulled and recleaned the injector and cup...new orings
oRings and copper washer. Bubble test again...fail.
Pulled glow plug from #3 , failed bubble test still.
Pulled glow plug from #1 , failed.
Pulled #5 , failed...pulled #7 ...failed.
With no glow plugs in the passenger head I am still bubbling up to the fuel filter housing. Pulled the banjo bolt from the front of the drivers side head...no more bubbles.
View 1 Replies
This morning I noticed when I started the truck had a rough idle shaking truck. The truck felt weak. Boost would go up but truck felt like it was in sand. While coasting on the highway at 50-55mph the truck not only lags in power but vibrates viciously until the overdrive kicks in that vibrations in cab and ssteering wheel go away.. What might be going on?
View 6 Replies
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 Replies
two days ago i noticed First start in the morning the truck billows out blue smoke. In mean is enough that looks like an old 2 stroke dirt bike. Quite alarming. I've had HHS in for 4300 miles or so. I hope I did not mess the engine up by towing With the HHS in there. The injectors have been getting loud an indication that i need to change the oil again. The truck always gets louder when nearing oil change time. It reminds me of an old chevy with bad valve seals. Would turbo seals just go. The smoke goes away after driving maybe 2 min well i can't see it while driving. Truck runs smooth doesn't stutter or miss. It has been acting like the stiction is happening upon first starting after sitting for 6+ hours.
View 14 Replies
My wife's 2011 F-350 on start up, will sweep the gauges from one side to the other. My 2012 doesn't, is that normal?
View 14 Replies
Get the message every time at start up and won't go away. It doesn't seem to be working when I back up near something. If one sensor goes does the whole system shut down? Also It won't let me check the "ON" box for the park aid.
View 6 Replies
