Ford 6.0L Power Stroke Diesel :: 2004 / Check Engine Light Came On
Jun 19, 2015
So last night my check engine light came on so I checked by by turbo and seen this hose not sure where it goes?
View 7 RepliesSo last night my check engine light came on so I checked by by turbo and seen this hose not sure where it goes?
View 7 RepliesMy low fuel light came on tonight. I drove about 2 miles, stopped and shut the truck off. When I restarted it and began to drive off to the fuel station a notice came on that isaid power reduced then a check engine light came on. I was about a mile or less from the fuel station so I filled up. I cycled the key but the engine light is still on. No low power message tho. The power is fine.
I came home and drained the water drain on the filter, didn't see any water but hoped it would solve the problem. I cycled the key a few times and started the truck but the light is still on. My truck is a 2013 f350 6.7 and has 211500 ish miles on it. I bought it a month ago with 18500 miles and haven't had any issue until tonight. My only thought is maybe the fuel filters need changed. I don't know if or when the previous owner changed them.
I started my '16 6.7 this am and drove it about a mile.
The check engine light came on and at the same time the display said "Reduced Power". I decide to turn around and try to make it back to my shop but shortly after turning around the display said "Low Fuel Pressure" and within a couple of hundred yards it shut down leaving me stranded by the side of the road.....
I called my local dealer who gave me the Ford Cares 800 number. I got a flat bed in about 1.5 hours which I didn't think was too bad considering I live in the country and they brought it to the dealer. The SA said it might be a couple of days before they could look at it as they were pretty busy... What it could be? The engine is stock with 9100 miles on it...
Check engine light is on...not blinking. All fluid levels are good. Mileage is 10,700. No code displayed in engineering mode. Truck seems to be running fine..
View 11 Replies2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
I found out today that the 2012 6.7 that I have purchased used with 30, 500 Miles on it a month ago has been in previously for warranty work. It appears that the previous owner took it in with a check engine light and after diagnostics found that the EGR cooler had "no Flow". Ford replaced the EGR cooler core under warranty before I bought it. (It now has 31, 950 on it). Normally I would think, GREAT, something I don't have to worry about doing. But being new to the diesel world, I was just wondering if this is something I should be concerned with. Anything else I should be keeping an eye on etc.... Also is this abnormal to occur with such low mileage?
View 14 RepliesI just replaced my batteries today on my 2011 F250 because of a no start situation. I guess it was about due since they were original and that gives me 5 + years of service and it happened in my driveway so I definitely am not complaining. However after I replaced them and started the truck the check eng lite came on....
View 8 RepliesIf doing a EGR delete on a early 2004 6.0 will turn on the check engine light? I was going to leave the valve in place and harness connected, I was just looking to add durability to the truck so don't want to use a tuner but also don't want the engine light on, I seen conflicting reports that it may or may not turn on the light!
View 3 RepliesI had a bad Glow Plug on my 2004 F350 6.0L Diesel causing the check engine light to go on. I replaced the Glow Plug and cleared the OBD2 error. The check engine light is off now, but I can't pass the smog check because EGR Monitor "Not Ready"
I put 100+ miles city/freeway miles on the truck, but I still get EGR Monitor "Not Ready" Even tried "Drive Cycle" with no luck...
My check engine light came on today and the code read P1335. What code is that?
View 14 RepliesCEL came on.. hooked up my cheap OBD/CAN scanner.. getting code P21B0..googled it and this is what i find: P21B0 - Reductant Level Sensor C Circuit High. What is this for? I've about had it with this truck..this having to replace a sensor every time I take it on a long trip stuff is getting ridiculous..2 EGT's, air charge cooler sensor, blower motor, and now this...
View 14 RepliesCheck engine light is on says low turbo boost but gauge says it has a lot of boost. Only happened after I put catalytic back on for smog test. Before that no problem.
View 10 RepliesWell another problem with my 11. It was just at the dealer getting the fuel pressure sensor replaced and then it started throwing a different check engine light. Dealer says it needs a new EGR cooler. They said there is a TSB for this. I don't have the exact code it was throwing right now. I haven't heard much about EGR coolers being a problem.
View 4 RepliesI have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
Noticed the other day when I went to leave a job site my Check Engine Light came on but the truck started fine and seemed to run normal. while cruising down the highway I noticed that my factory boost gauge was showing 35psi and fluctuating between that and around 10. looking at my H&S it was showing normal boost readings for the current driving condition, when I came to a stop the H&S would show 0psi but the factory one would fluctuate between 0 and 35-40psi..
I can tell the turbo is not spooling at all during this time. if I take off from a stop with the gauge showing 35 the engine sounds louder than normal at first take off compared to when the gauge is reading normal. I haven't gotten a change to get it in my shop yet to look it over but does the dash gauge read from a different sensor that what my H&S is reading? Truck is an '11 F250, deleted both EGR and DPF with H&S tuner. I checked codes and all I have is P06A7. Where to start?
My 04 F 350 started with a check gauge light while going down hill towing an 18 ft car hauler full of mulch. Did it for 5 seconds, then when we got to our land and I was getting ready to back up it did it again. and this time my oil pressure gauge was at zero. I shut her down. checked the oil. its full. Drive home everything is good. Today I'm getting fuel pressure gauge going nuts. 80 to 100 PSI. at idle no oil pressure and the check gauge light. but the engine is still running. Oil was changed 4K ago. fuel filters same. Where to start looking?
View 5 RepliesI am at 34,600 miles and had the oil changed yesterday afternoon. My son picked the truck up for me and on his way home the "drive to clean exhaust message" came on with the "check engine light" at the same time. I get home from work, re-check owners manual and no mention of the check engine light coming on with the drive to clean message.
I called my service rep and he says drive it as per owners manual, so I head out drive about 45 miles, averaging 60 mph nothing changes, both lights/messages are still on. Truck seems to be running fine and the last cleaning exhaust message was Sunday and I believe I was out long enough for it to do its job. It will go into the shop tomorrow, but was looking for thoughts from the the rest of you pros before I go.
I mention the oil change only because after the last oil change at around 30,000 miles I drive to work 2 days after and my water pump starts leaking.. coincidence I know.. but getting freaked out as I approach 36000 miles..Truck is a 2011 and I bought it new in Jan of 11.
Truck had a check engine light that came on. Plugged in scanner while I was still running it, said egr volts were weak, i just cleaned it yesterday.. and earlier today reset the check engine light once but then drove about 30 miles with no reoccurrence of light. Now i pulled over, shut off truck unplugged egr and reconnected. Went back to start my truck and nothing at all. Its like I am trying to start it in park.....been here for about 3 hrs now I've checked fuses nothing is blown. I am just sitting here freezing trying to fig out anything i can on line....... Its a 2006 f350 6.0 ty
View 14 RepliesI just bought a 2016 F250 with the diesel and thought I'd share an early ownership experience. At about the 1300 mile mark the check engine light came on and other than the remote start not working the truck continued to run great. I pulled a P0170 code, Fuel Trim Bank 1. And since the truck was still running fine, I considered clearing the code and see if it would come back. But since it's under warranty I decided to bring it to the dealer. They checked it out and diagnosed a bad Fuel Rail Pressure (FRP) sensor. They swapped it out and it seems to be good to go (no more light). While I was in there I asked them to turn on the DPF percentage full screen which they did.
View 3 RepliesI have a 2006 f250 with 120k. I am having trouble getting the water in fuel light off. I drainned the water out and replaced both filters and the fuel water sensor. The check engine light is now on and the water in fuel light is as well. I'm stumped and can't figure out what to do next. Will the check engine light come on as well with the water in fuel light or is it two different problems?
View 2 Replies