Ford 6.0L Power Stroke Diesel :: 2004 - A/C Malfunction - Coolant Temp Hits 218 Then Fan Works?
Jul 21, 2016
I have an 04 F350 and I was wondering if the fan is supposed to be locked up when the A/C is on. In max A/C with the fan on 3 it's barely keeping cool in the 95 degree heat we have been having. If I rev the engine I don't hear the fan noise like I do when the coolant temp hits 218 and the fan roars. Freon was replaced several months ago, along with receiver/dryer and orifice tube when I did the HG's. The A/C shop drew a vacume and did not find any leaks.
View 7 Replies
Advertisement
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies
Ever since having the EGR delete done, the oil temp has been LOWER than the coolant temp. I am assuming this is bad info from the sending unit? They are reading with in a degree of each other at start up, but when at operating temp the gauge will read lower. Before the EGR delete I had a delta of about 4-7* oil hotter than coolant.
View 1 Replies
I've been searching for a while now but have not found an exact match to my problem.
So, Yesterday I was pulling a large load home (15K lbs) over flat land/small rolling hills and I experienced a coolant temp spike. And I am trying to figure out what caused it. I was traveling 65 mph about 2k rpm and 20lbs of boost, I was motioning the ECT, EOT, TFT, and Fan Speed via my scanguage and 99% of the time the ECT was in the 209-220 range, once it got up to 220 the fan would come on and the ECT would drop to 209 ish pretty quickly.
However, twice the ECT shot up from 215 ish to 240 within seconds then the dash indicator said check coolant temp then the fan came on and cooled it down to 200 within seconds, I did lose about 1/2 gal of coolant. So today I'm going to get a new degas cap (still OEM original) and continue to monitor the situation.
My EOT ECT delta has been a constant 10-13 degrees for the 3 years i've been monitoring it so i believe my oil cooler is still functions within spec and all my cold soak temps are within a degree or two for various ambient temps (20 -80) so all my sensors should be good.
Also, tonight I'm going to pull the EGR valve and check if there is any coolant in the intake, but if there is not, where should I start looking and what should I start worrying about e.g. head gaskets?
View 12 Replies
This is the only 6.0 I have owned. My tranny temp (with the Torque Pro) is pretty much always the same as my ECT. My ECT will move, and less than 2 seconds later, the tranny will move to the same temp. Is this normal? I was expecting lower tranny temps, but maybe it should be the same because of sharing the radiator.
View 11 Replies
The truck has been just terrific, mostly used for towing our travel trailer. Earlier this year i developed a leak and lost 3 quarts of oil before I caught it. I would think with 15 quarts in her this shouldn't have been too big a deal. However, I am now experiencing 10-15 degree swings between ECT and EOT. Before I give the particulars, yes, I have had three new thermostats, two Ford and one brand X.
Anyway, coolant temps are 184-200 depending upon load, terrain, etc. At the same time, oil temps run 205-230. There is no oil cooler to get plugged up. She's got 120K on the clock, doesn't burn oil, no disappearing coolant. I am concerned about blowing a head gasket or other serious damage at these temps, but don't have a clue where to start? Yes, the fan does come on, but still this seems plenty hot.
View 14 Replies
What the coolant temp should be around after plugging in the block heater overnight? Not looking for an exact measurement since this can be affected by OAT and the length of time it has been plugged in. But when it's -15 to -20F this weekend I was wondering what to expect.
View 13 Replies
I have a 2006 350. When I am pulling my camp trailer (about 12,500 lbs) up a grade I hear a fan or blower turn on and I get a high pitched squeal. It will also have a beep and my in dash display will say high engine temp. I have a bullydog pmt programmer (i tow with it in stock mode) the display will show my coolant temp at about 180 degrees. If I pull over and let it idle for about 2 minutes the warning clears and the temp gauge returns to normal. the display reads about 180 degrees the whole time this goes on. I know the engine is not over heating so why do i get this warning and squeal?
View 4 Replies
My truck's been doing this ever since I got it when the engine is cold. Haven't brought it up to a dealer yet because I'm not sure it's a real problem, and since it only does it when it's cold I'd have to leave it overnight.
It seems to happen when the turbo hits a certain RPM. I got it on video but you can't really hear it until the end when I raise the RPMs a bit.
YouTube - VID 20100926 104950
View 14 Replies
Coolant temps getting much higher than oil temps under load. Is there any problem that could cause this other than a bad temperature sensor? Reading temps with an Edge CTS 2 monitor. Think I'm going to hook up a mechanical gauge in the morning and see what it shows.
View 8 Replies
I am going to install a coolant filter on my 2004 6.0 E350 van. I have read threads about bypass filters and full flow filters and I started asking myself "Why use a bypass when I can filter all of the coolant?"
Is there any reason why someone should use a bypass filter? I bought the van used knowing I would eventually have to do most if not all of the 6.0 repairs. IPR sells a complete coolant filter.
I talked with the people at FICM repair and they suggested I do my research but leaned towards the IPR cooler. Ed spent a good 30 minutes on the phone answering all my questions and never asked if I wanted to buy anything. If anything, he was trying to stop me from throwing money at the van until I isolated what needs to be repaired.
I already bought the Sinister Kit and requested a return.
View 10 Replies
So I recently bought a '04 F-250 early build with the 6.0 powerstroke. Truck drove fine for the first 1000 miles. Drove from Fort Hood back home for leave. Got home and truck sat for two days, started it up and it ran for 15 minutes, then shut off on me. Temp gauge read normal, but after it shut off, I turned the key off and back on and temp gauge was maxed out. And truck has to cool down before it will start again. Replaced the IPR Sensor to no luck. Not sure if I have an ICP sensor issue or what it could be.
View 11 Replies
I have an 04 f-350 that I did an EGR delete, new Ford oil cooler, new radiator (not ford), new thermostat (not ford), coolant filter, glow plugs and harness, MBRP theoretical 4in downpipe (was 3.5 to converter) flushed cooling system with lots of tap water before the delete, replaced coolant with Cat 1 ELC and distilled water, fresh T6 5W-40 and filter, several weeks ago. Was troubleshooting a wireing problem and found what looks like oil sludge in the degass bottle while under the hood.
Possible that while doing EGR delete I clipped a gasket? Truck runs great, no smoke out the tail pipe. There is what looks like about a cup floating on top the coolant. Oil level is down about a 1/2 quart and clean, no water in it. Where do I start looking?
View 14 Replies
I have a 04 f350 6.0 with about 195xxx miles on it. The other day my truck started acting up. It starts and idles without a problem and drives fine till the engine gets to operating temp once there I cannot accelerate quickly like getting onto the highway to get up to speed it just the motor just goes quiet and won't accelerate. It usually does this a little after 2000 rpm. I can let off the throttle and slowly get to speed as long as I don't go past 2000 rpm. No check engine light was not on scanned it and got p0611 for the ficm. I tested the ficm and it read 48v with key on. While truck was running I got 46.xx v then Started to climb to almost 48v. The truck was warm but not at operating temp where the problems starts(didn't have time to let it warm up all the way) could these symptoms be the ficm still? What else should I test?
View 5 Replies
I recently was informed by my local mechanic that fuel was leaking into my coolant. He said I had a cracked head based on this and it would give soon. Well, he was right, and now I need to do a head job. I found new heads, but would like to know how many book hours this should take before I proceed. He gives me a wide range of time, and don't want to get taken advantage of.
View 4 Replies
I just did a pressure check on the cooling system on my 04 6 liter. It reached 16lbs towing an enclosed trailer and into a strong head wind. I was just wondering what's the Normal pressure suppose to be, or is there a Normal pressure. I'm using the new style cap with the larger spring in it and it didn't kick any coolant out.
View 14 Replies
I spotted a leak last nite on my 6.0. It is coolant, running down the right rear on 2 metal lines that go to the trans I think. It was dark and 24 degrees so I did not spend too much time looking. Shut the mother down til I could research. 2004 250, 6.0 FX4x4, stock. Coolant was changed to green by previous owner. Bought it 4 months ago. 187,000 miles.....
View 14 Replies
While servicing the bosses 121k 6.0, I noticed the coolant resevoir empty. It took 1 1/2 gallons to bring to proper level. Returning under truck to install drain plug, I noticed coolant coming from rear of the engine(right side). And of course Ford has changed the cooling system cap, so I wasn't able to pressure test it to pinpoint the leak. Started the engine and seen coolant coming from the left rear as well. I've been reading here to see what others have been seeing, (EGR cooler, head gaskets). With all the heat shields,not much room to look.
After work I did go and buy the adapter to test the cooling system. With any luck I will be able to see leak better.
View 14 Replies
I have coolant blowing out of my coolant reservoir when ever i hold it to the floor it does it with or without the banks programmer... 6.0L power stroke...
View 14 Replies
Well got home and the front of the truck was covered in coolant. I must have driven 2 hrs after I noticed no coolant pressure, but temperature was great so figured it was another crappy cap. Looking to get a quick turnaround. Need to go out of town for work Saturday so I have this week to get it done.
Just put a stock unit back in? I don't think I need to do anything else in that area. Belt/pulleys/radiator all done last spring.
View 9 Replies
This weekend my friend and I plan on doing a coolant flush, new Mishimoto thermostat housing with high temp thermostat and install a Mishimoto coolant filter.
Truck currently has some unknown green coolant in it and Im going to replace it with Rotella ELC. I plan on doing a couple hose water flushes then follow with about 5 distilled water flushes. I've been reading about putting some Cascade in on first flush to dissolve any silicate goo that might be in there hanging out. I might give that a try. Im sure I can manage this part from all the stuff I read about doing flushes.
This is the part that looks like a little more work involved than the flush. Doing the thermostat kind of worries me because of the tight area in there to work with the fuel line and the EBP sensor being right there. The current thermostat holds temps around 175-185 under normal driving. I bought the new Mishimoto thermostat housing with the high temp thermostat installed in it when they had their pre sale going on for the housing.
I decided to just go with the whole thing because of all the stuff I read about people having issues with the thermostat not fitting the older housing correctly since Im certain I have the original housing from 2004, like everything else that's still original on my truck. I plan on removing the thermostat before doing the flushes and then installing the new housing and thermostat and coolant filter before I add the ELC.
The coolant filter install looks fairly simple to do so I should be ok with that.
View 11 Replies
