Ford 6.0L Power Stroke Diesel :: 2003 - Cooling Fan Rev Up And Down Every 10 To 15 Seconds - Normal?
Jan 27, 2016
I currently have a 2003 F-250 6.0 with 112,000 miles on it. While traveling interstate speeds (70+) and the I can hear the cooling fan rev up and down every 10-15 seconds. Is this normal?
Also when it spins up, it sounds normal then make a high pitched squealing noise. Thoughts?
I am also needing to rebuild the fuel bowl. I noticed DieselOrings offers rebuilds for the 7.3 but not the 6.0. Will these fit or any suggestions on parts?
View 7 Replies
Advertisement
I have a 2007 6.0 that this has happened to twice now. It's fine around town but I never hear the can come on. Friday when on the interstate my my temp gauge started to rise past normal operating temperature before fan came on. Is this normal? After the fan came on it stayed at normal temp for the rest of trip....
View 5 Replies
I have a 2003 6.0 Exc. I have installed an external "Bullet Proof" oil cooler, and essentially all of the "bullet proofing" accessories with the exception of head studs. I also have installed a Mishimoto oil cooler, as the OEM cooler had a crack in the upper tank, My particular problem is that the cooling fan does not kick on (audibly) until about 230 deg or so. It quickly cools to about 215, and the fan kicks off (audibly). On the long uphills here in AZ, it will repeat this process, sometimes getting as high as 240deg.
(As monitored by my EDGE tuner) I have utilized the blue-wire-to-ground trick noted elsewhere, manually turning the fan on myself, and that works great. What I'm asking, is what sensor sends coolant temp to the ECU, ( and where is it located in the cooling system) which in turn determines how much to turn the cooling fan on? What typical level the sensor sends to the ECU to control the fan? I would like to put together a circuit that "fools" the ECU into turning the fan full "on" at about 210 deg, and stays on until the coolant temp reaches 195 or so. I would like to check that sensor first, and make sure it is working correctly before I try to band aid a fix.
View 14 Replies
Under normal driving, my cooling fan rarely comes on. The truck runs ECT 194 to 200 and EOT about 7-8 degrees warmer. On grades in the mountains, not towing, it will cycle on if the ECT gets to 210, cools it down and cycles again if needed. My question is, under similar conditions, what does your truck do? When towing my 5th wheel, about 13k, when its 90 degrees plus, at between 60 and 65mph on level ground, my ECT runs 210 and the fan comes on to around 1400rpm and cools it back down to about 204.
When the ECT gets back to 210, the fan does the same. On uphill grades, I see as much as 220 ECT. When this happens the fan comes on at around 2500rpm and cools it down to about 199 pretty quickly. I have a new oil cooler so my oil always follows and on my last trip I never saw more than EOT of 225 on the longest, steepest grade. The reason I ask is to see if this seems normal. My mech keeps mentioning that if my fan is cycling it may be head gaskets. But, I don't have any other head gasket symptoms. I think it seems pretty normal. If the fan doesn't come on and cool the engine when its working this hard, then what is it for? What does your truck do under similar conditions?
View 11 Replies
The 2011 Platinum's "black" interior is really chocolate in color. This just killed a potential sale today. But I did drive it and it didn't dissapoint. Probably out of my price range,but if money wasn't and object, probably would go for the loaded blk. 4x4 Platinum.
View 8 Replies
This applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 Replies
getting ready to do a cooling system flush per the instructions Cheezit posted a while back, which say "refer to Cooling System Draining, Filling and Bleeding in this section." I think I can figure out the drain and fill but how do you bleed the system?
View 14 Replies
My truck was parked at home and hadn't been started for 10 days. When I did start it for the first time, I heard the cooling fan spooling up or down, consistent with the engine rpm. After pulling away from my home I saw the fan speed spool up to near 2,800 rpm during the short period it was locked-in with the engine speed.
While driving out of my neighborhood, and about 1/3 of a mile from my house, the fan returned to normal speed of about 480 rpm. I have the FSS pid displayed on my Scangauge and was able to see the fan speed while hearing it. Now I know what the fan sounds like at a high rpm. It makes quite a roar.
This has never happened before. I've driven the truck a few times since then and it hasn't occurred again. What may have caused this?
View 7 Replies
My truck is all stock and I am running in performance tune? And my friend the former owner said I need to let her loose about 75 percent of the time I am driving it because it's my DD and I do not tow anything on a regular basis. I do not want to stretch my bolts by unnecessary pushing, I don't know if I'm even pushing it hard but I normally get the turbo up to about 30 psi is that to much?
View 8 Replies
2006 F350 6.0 throwing code P0480 and I'm having a hard time figuring anything out pertaining to my truck. Trying to figure out what exactly it is and how to fix it myself.
View 3 Replies
My engine cooling fan came on when I first started the truck, was reading of 2k on torque app, ECT was appx 100* with the EOT a little cooler after about 5-10 minutes things went to normal around 600 rpm. It did not happen anymore during the drive, I was seeing about 192* ECT and 198-200 EOT. I let her set for 2 days and took her to town and the fan was at normal RPM's, Is there any problems or is that normal?
View 9 Replies
I noticed my A/C hasn't been up to par. It's not bad when driving but just ok when idling. So today I changed the orfice tube and the accumulator. Vacuumed the sys. down and charged it up, 2 lbs 10 oz. It is worse! the compressor kicks on and off constantly only cooling to 80 degrees.
I noticed the high goes right up to 350 then the compressor shuts off .... 7 seconds later, back on and up to 350lbs and off again. I think the high-pressure switch is shutting the compressor off before anything goes kaboom but why isn't my fan cooling the condenser down? my FSS shows no increase in fan speed. Sitting at 450.
I think I'm going to cool the condenser down with a hose now to see if that works. If so, That would be telling me the fan isn't doing it's job correct?
View 5 Replies
I have an early 04, I'm not sure if there's a different in pressure over the years. But I'm curious what normal or average readings are. Btw I did replace the icp and pig tail last year. Here is what I have in psi from my sct
Cold start at idle 680 .23v
Warm idle 635 .24v
Cruising 1800rpms about 1500 .32v
WOT about 4200 .78v
View 14 Replies
I wasn't sure if I should be having any sway at all while pulling our new 30' TT. Dry wieght is 7200lbs, GVW is right at 9500lbs, tongue weight is around 800lbs, and I'm running a Fastway E2 WDH with sway control built in. While towing this weekend, I was experiencing a very slight amount of sway. It wasn't what I considered to be much of an issue but my wife and daughter both asked why the truck felt as if it was moving side to side slightly. When I say slightly, imagine a small glass of water filled about 1/4" from the top. The sway wouldn't have been enough to spill the water, but enough to sway it slightly back and forth. Winds were about 3-8mph hitting me from the north west (in relations to my trucks heading).
I do have some suspension enhancements that might have contributed to the sway. I have roughly increased the rear end by 4" by adding add-a-leafs and F350 blocks. I have Fox 2.0 shocks and a Helwig Bigwig sway bar. Plus I'm running 295 Nitto Trail grapplers , all 4 at 80psi. I've read that the more aggressive tires could also be a contributor.
My question ultimately is: should I be feeling any sway at all? Is a very slight amount of sway normal when pulling a 30' 9500lb rear hitch pull?
View 14 Replies
It takes about 10 minutes for the truck to drive normal. If I start the truck and sit for 5 minutes, then start driving... the truck has a very hard time changing gears and accelerating. Just trying to see if this is normal or not ?
View 14 Replies
Decided to try and swap in LED bulbs into the sub par factory headlights and since some engineer somewhere decided it would be easier for me to have to remove the grill and headlights just to change a bulb, I noticed that the dual horn set up had the horns pointing back to the truck. Even worse, right in front of all the fins on the CAC, Raidator, etc. to reduce muffle the sound.
Now I don't know how things are where you live, but generally when I honk at someone, I'm not doing it so I can hear my own horn. The general idea I thought was so that others could hear my horn.
Of course the same engineers in charge of headlight bulb swaps also figured out the wiring for the horns so you can't just loosen the nuts (10 mm) and rotate said horns 180 degrees. You can rotate the driver side horn 180 degrees and call it good, but the factory wiring won't reach the passenger side horn if you rotate it.
You can however remove both horns and use a small screwdriver to unplug the harness that joins the two horns. If you swap the horns right to left and left to right, then you can put the factory wiring back together in a manner that leaves the horn outlets pointing forward towards others.
I can't insert pics into the thread as I describe things. I used to do that but FTE seems to have gotten rid of my gallery so I can't upload to there anymore and then post photos in the thread that way. So now you get them uploaded as attachments at the end of my rambling.
View 8 Replies
Noticed this past month on colder days my upper hose is collapsed, typically a symptom of a bad radiator pressure cap.
This hose is connected from the water pump to the radiator. The radiator is connected to the Degas bottle which has a nonstandard radiator cap.
Do these plastic caps vent the same way a typical cap does?
Cap for 2011 Ford F-350 Super Duty|9C3Z-8101-B
View 3 Replies
What the normal tire pressures are so the TPS will not alarm? The sticker on the door says 65 front and 80 rear for my F-350, but I think this is a bit high when empty or not pulling trailers, etc. Additionally, is there anyway to adjust the TPS settings?
View 10 Replies
I'm having a bit of a cold start issue, need to know if it is normal or something is wrong. I live in southern Indiana and it's gotten down to a VERY cold 50 degrees (lol) and the past two mornings I have started it up and it seems to have a misfire first thing in the morning and it will kick into high-idle mode and after I shut it off and start it back up about 20 seconds later after the ECT gets above 100* and it runs perfectly. It has brand new 190/100 injectors from Warren, an IDP tune, and I am running 13 quarts of FoMoCo 15w-40 oil with 2 quarts of hot shot stiction eliminator (tried it before installing new injectors). And also throwing no codes. Is this normal or should I be looking for a problem?
View 13 Replies
I have a 12 cc 4x4 drw. I hauled a bull and a cow about 100 miles this morning. I was pullling approx 6k including the trailer. The temp was about 75*. 50-60 miles into the trip I switched to the oil temp screen and the oil temp was 224* and the trannie was 199*. I was going into the wind which was about 20 mph, and I was traveling 75mph. The truck never lugged down heck it never shifted out of 6th gear. When I unloaded the cattle the temp came back down around 190*. Headed home and the temp got up to 226* and the tranni went to 205*. This was going with the wind and just the trailer. I am using oem 10w-30 motorcraft and motorcraft filters. The truck just has 9k miles on it. I am thinking that the oil temp is a little warm, should I be worried. What should I look for to diagnose. I like to do my own diagnosing if I can, the dealers around me can't find anything wrong even if you point the leak out to them. Should I be using a different oil?
View 14 Replies
I know it seems like everyone's truck tends to have different tolerances when it comes to when it starts and stops regen when it comes to gpl but the last two times my truck has gone into regen it starts at 100% and finishes at 25%. Is it normal to stop regen when it gets to 25% or should it be stopping at 0%. Or could it be that the percentage in my truck is off and it's actually using the gpl to start and Stop? The only thing about that is that forscan says it's supposed to start at 100% which it does so if my percentage is off that would mean it was starting at 75% does it not?
View 14 Replies
