Ford 6.0L Power Stroke Diesel :: 2003 XLT - HPOP Cover Leaking
Oct 24, 2015
A good friend of mine just bought a 2003 xlt with the 6.0 and has an oil leak at the HPOP cover as far as he can tell. Looking for a good write up that explains how to get to where we need to go. Also maybe a list of o-rings and gaskets that will be needed on the journey. Is there anything else that may need attention while we are in that deep. I have read about the SVT fitting but not sure what that is or where. The EGR has been deleted.
View 12 Replies
Advertisement
When I pulled my HPOP cover the other day, noticed some RTV on each side where you have the small step down from the block and the piece of metal on the backside of the pump housing. The new gasket I installed had he step down and looked like it would fill the gap, but is the RTV necessary?
There was a previous leak on the turbo drain tube that the dealer I bought it from tried to stuff some kind of fiberglass material in there to absorb the oil. I half wonder if the dealer didn't try to "fix" the back of the cover leaking by cramming some RTV in there. I have to pull the cover again in a couple days and wanted to see if I needed to do anything special when installing the cover?
View 6 Replies
I need to get the HPOP reservoir top cover off so I can drill/tap a gauge probe into it.
I see torque-head bolts, and a few long bolts that go all the way down into the HPOP.
Unfortunately I cannot get two of the torque-head bolts out because they only un-thread several rotations before the heads of the bolts hit the edge of the fuel filter canister/bowl.
Any tips or tricks?
View 12 Replies
I need to get the HPOP reservoir top cover off so I can drill/tap a gauge probe into it. I see torque-head bolts, and a few long bolts that go all the way down into the HPOP.
Unfortunately I cannot get two of the torque-head bolts out because they only un-thread several rotations before the heads of the bolts hit the edge of the fuel filter canister/bowl.
View 14 Replies
I did the extended seal kit and non-serviceable plug on my HPOP and now the CEL is on. It is throwing the below codes. The truck in all reality runs fine and even a little better on a cold start than before resealing, just the CEL is on.
P1280
P1209
P1282
P1212
P1211
I cleaned the IPR when it was out when I put new seals on it but could it go bad by just taking it apart? The ICP and IPR are definitely plugged in. The truck is all stock, no chips.
View 3 Replies
I have a 7.3 and I think it's leaking oil out of the HPOP but I'm really not positive.
View 2 Replies
Well my hpop is cracked and leaking alot I need to get home this sucks I must of tighted it too hard
View 14 Replies
about to fix my leaking HPOP and step up to an Adrenaline. Looking at replacing the discharge fittings when I do and have a quick question. Dieselsite instructions say the oring seals it and to only run it down to where the fitting body touches the pump. Diesel orings instructions say the 680 locktite does the sealing and to torque to 25 ft/lbs.
View 12 Replies
Pretty sure my rear plug is leaking on my HPOP. It has a nylon washer under it which is different than what I have seen on all the write ups. I bought the truck with 189k on it five years ago.
I attached a photo....
View 2 Replies
My HPOP was leaking so I pulled it our last weekend along with the fuel bowl and put all new seals in. All my previous leaks are sealed but now this stupid fuel bowl is being a major PIA.
The return line coming off the FPR will not stop leaking! It was slowly dripping when I first replaced the bowl and I thought the leak was between the fuel bowl and FPR housing. I ordered new rings and put it back together.... still leaking.
I wrapped a towel around the fuel fitting and realized that is were the leak is actually coming from. I went to the parker store today and got 3 new 60VL5 sleeves. The first one tore while sling over the fuel line (I was using 2cycle oil as lubricate). The second one leaked even worse.
In a desperate attempt to stop the leak, I slid the sleeve onto the fuel line as far back as it would go. I inserted the fuel line into the bowl and then put a thin coat of rtv on the exposed fuel line. I slid the sleeve over the rtv and then put a light coat of the outside of the sleeve. I tightened the nut up and am waiting for things to dry before trying again.
Why is this fitting giving me such a hard time? I've pulled the FPR housing and it is not cracked so I don't know what the deal is.
View 6 Replies
2003 f350 6.0. Ran last night and wont start today. Monitor says 85 psi pressure, should be atleast 500 to start. Could it be the IPR?
View 4 Replies
Finally got the hpop in my 03 done, got it fired up and runs great. The longer crank times seem to be getting better, however I am a bit concerned when I really get into her I am seeing pressures of 3400 psi......seems high to me. I guess I don't know for sure what the IPR was reading, will have to check that. Truck runs great, nice and smooth, but I am afraid I am going to blow something.
What is normal and what is not? Is there a way this pump will dump excessive pressures if needed? Or is it just a matter of time before I blow an oring out somewhere? I'm not sure how much the pump is capable of putting out. At idle it's sitting right around 630 after warmed up, maybe a bit lower.
View 8 Replies
2003 with hot no start issues. It starts fine in the morning however will not start again after the engine gets warm, after an hour or so of cooling off it will eventually go. Not sure if I should start with.... Readings below ....
FICM L 13.5v
FICM M 48v koeo and 47 running
IPR 14.7% koeo
IPR 74.6% cranking (no start while hot)
IPR 40% (after cold start while running
ICP 737psi cold start
ICP 1600psi engine running 2k rpm
ICP 360 hot while cranking
View 14 Replies
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 Replies
Quick question, does an early 04 have an SCT on the HPOP that can be upgraded?
View 7 Replies
How does one pressure test for air leaks??? Truck is a 04/04 F250 with 198K ICP sensor in the valve cover.
View 7 Replies
Just replaced the hpop on my 04' 6.0. It had been down for about a year because my low pressure oil light would come on after warm up. Truck ran PERFECT, but dam light would come on. Eventually it wouldn't start by cranking, but would on a bump. (I have a 6spd.) still ran good. I would never run it over 5 minutes because i didn't want to damage anything. Finally getting around to fix it.
After a day of air testing, we tracked it down to hpop. (air coming out of turbo drain tube). I had a hunch that the dam bb on pump had spit out from similar stories on FTE, and thats what happened.
Replaced pump. (its an older style pump BTW, although i have a january 04 build and every ford parts guy said differently.) Put everything back together and now it runs terrible! We ran the truck for over 20 minutes and it didn't get better. I am afraid its gonna damage something to keep running it. My mechanic says 5 cylinders are misfiring and its something to do with the ficm or injector harness.... But, it ran perfect right before the hpop change???? Everything was double checked to make sure it wasn't something dumb.
View 13 Replies
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....
View 14 Replies
July 11, 2013 replaced HPOP. June 26, 2014, Going down I20 in Dallas engine shuts off. Three days later Ford techs declare said HPOP dead . Looking at another HPOP along with stand pipes and dummy plug seals. Hopefully I can get some warranty relief on the pump. Do these things eat HPOP?
View 14 Replies
I've gone through every possible step in diagnosing myself but can't seem to figure it out. I do not have access to shop air to do an air test. Vehicle history that I know of: Has updated STC fitting, looks to be a reman hpop. I have tested the LPOP with the oil filter housing, fills quite fast, although no pressure registers while cranking on the gauge. When I opened the HPOP case to take a look, I found the reservoir dry. What can cause the LPOP to not feed the HPOP? I will be updating everything. The truck has relatively low KMs sitting at only 163,000.
View 14 Replies
05 excursion with 04 motor. 290k miles. Had a crank no start issue. Pressure tested hpop only got 450 pressure. So got a brand new on from ford. Also did standpipe, and dummy plugs. After forever and day of cranking truck fired up. Sounded great let it sit for 30 min. Took it out for ride, mile down the road lost all power. Alternator was bad, replaced that and battered just to be safe. Now truck won't fire and have zero pressure. Something that could of been tripped during power surge?
View 8 Replies
