Ford 6.0L Power Stroke Diesel :: 2003 - Run Rough And Stalls Eventually?
Apr 4, 2015
I have '03 6.0 when it gets to full temp it will run horrible and eventually stall. It will take a few long cranks to restart. will drive a little bit but will stall again. It will idle all day long even after a stall. IPR @hot idle is 22 and ICP @hot idle is 640. IPR and IPC readings seem to run good throughout the rpm range except for when it dies. Then the IPR is anywhere from 71 to 85. Has new ICP and Pigtail. Runs very good until hot. I am leaning towards HPOP.
View 14 Replies
Advertisement
So the last couple times I got a car wash the truck started running real rough, sometimes dies, then runs fine after a few minutes. Well, the last car wash I got it did it again, but the issue didn't go away. I checked the injector plugs, cleaned and greased, no change. Validated the bowl is filling with fuel, changed fuel filter, no luck.
Sometimes it will start and idle fine, rev in neutral fine, if you come off throttle abruptly it will fall below normal idle and start stumbling with an SES light and eventually die.
I managed to get it idling good, started logging with TPro (attached) and it was throwing codes P0475 - Exhaust Pressure Control Valve, and P0705 - Transmission Range Sensor Circuit Malfunction, as well as P1211, p1249, p1316 listed as 'multiple descriptions'.
I'm assuming this is an electrical issue since it happened after washing the truck, just not sure what sensor would cause all this?
View 14 Replies
Rough idle I have had for little bit.Would stall out at idle or a stop, but fire right up? No one could figure it out with the stalling, but now its bad, started yesterday. Have white/blueish smoke sometimes, ( white smoke smells fuel) on restart after warmed when it dies, first time it took 25 mins to restart, now only takes 5 to 15 mins, when I step on it INCREDIBLE full power, fuel mileage gone to hell also since yesterday. Had full tank, now 1/2 tank.
No problems on cold start at all, no check light, 325,000 and never had this before.
Bad fuel?
ICP?
FICM?
Recent work, new turbo, ( turbo was original turbo installed when built) cooling line to waterpump, oil change, new fuel filters, front brakes and 2 new batteries.
View 5 Replies
Truck has a rough idle and finally just stalls out. I replace the under valve cover wiring harness and put in new glow plugs. With valve covers still off I started the truck in the issue still persist. I went ahead and unplugged each injector and each time the motor had a hick up .
What am I pulling apart and replacing next?
View 13 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
2004 later year 6.0 F-350. 155,000 miles. All stock.
It will start and run fine. Drove it for an hour then began running rough. Nursed it back home. When idling it eventually died. It will eventually fire up but runs really bad. It has done this a few times. I've done fuel filters and 911 fuel treatment because thought it was gelling. No luck...
It has injector circuit fault codes that pop up. Only other code is MAF sensor low but in range. First it was codes for cylinders 3,5. Then 3,5,8. Then 1,3,5,8. Now just injector 1. Keeps changing as I refresh. Battery power fine. FICM is 47.5- 48volts and in sync. ICP at idle is 600-700psi. IPR is 25%.
We had a problem with blowing turbo pipe off so may be overboosting. Not sure. No code thrown relating to that. Possible wire chafing? Maybe bad tank of fuel? Not sure where to turn at this point.
View 14 Replies
I've got an 03 f250 superduty and a few weeks ago i was driving home pulled to the side of the road to get a phone call and my truck sounded like it was misfiring and started to shake very rough so i quickly got it home and it barely made it up hills with no power at all, took it to the mechanic and he said it was my wiring harness, so i replaced it and it took weeks to get here and i finally get it in and my truck still seems to be misfiring ad idling very rough, I replaced my oil less then 1000km ago and I've had 2 injectors replaced. I've talked to a few diesel mechs and he recommended to put some hot shots in it.
View 14 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
View 14 Replies
'03 6.0 Powerstroke. Rough idle AFTER it warms up. Runs fine cold. It seems to studder and miss at mid range acceleration. Egr deleted and new oil cooler installed. New lift pump. Replaced ICP sensor. Have 48.5 volts at the FICM. Replaced the fuel pressure spring to the blue one. All new filters. Does not smoke. Does not throw codes. I need to fix this truck one last time. It has a date with the bottem of a very deep lake! It has been nothing but a pos since it hit the ripe old age of 25k miles!
View 14 Replies
Proud new owner of a 2001 7.3....today. The previous owner installed Warn standard hubs. I assume they work same as OEM with the exception that I have to get out and lock them, right? Also, when I test drove it, and after locking them, I engaged to 4x4 button and the 4x4 engaged and worked. However, when I disengaged my AC went to defrost just like my old 7.3. The AC eventually came back. Is this normal? I think it also went to defrost when I engaged. The AC does come back after a couple minutes after disengaging.
View 14 Replies
My 1999 F550 7.3L has been hard to start when it's cold outside since I got it with about 150k on it (it has 200k on it now). Last year we tested the glow plugs and sure enough 5 of 8 were bad. So they are all new now. It worked a little with the hard start, but not much.
When it's cold out the engine will crank forever amongst clouds of smoke and the smell of unburnt diesel fuel and sometimes eventually start, followed by smoke and sputtering until the cylinders clear out. However, what I have noticed recently is that it will sometimes start in the first few revolutions. It seems like the best way to start cold is as follows:
1. Let the glow plugs heat up for a minute or two,
2. Crank engine for 10 or 15 seconds and stop,
3. Crank engine again, but stop if it doesn't catch in the first couple of revolutions,
4. Repeat step 3 until engine starts.
When it starts using this method, it's immediate and it's running smoothly immediately with minimal smoke. This is making me think there's a computer or sensor issue, but I have no codes.
View 13 Replies
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
View 14 Replies
My 2012 diesel frequently stalls momentarily after I touch the brake. This is very annoying as I drive in heavy traffic and often have to touch the brake then accelerate to merge into freeway traffic. The dealer service department said this was a 'feature' and not a flaw. Is there any way to eliminate this issue?
View 5 Replies
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
View 7 Replies
On Tuesday morning I was watching an auction on my computer and saw a 2003 Ford F350 Super Duty Crew Cab Fx4 with 200K on it. It had an inspection report which is *supposed* to note every cosmetic and mechanical issue. It had nothing listed wrong with it for mechanical. I "won" and for my prize I get a rough-running 6.0 diesel delivered.
I just got off the phone with the transporter who picked it up today and he said there are no check engine lights but it is running rough with no power. So I am having him drop it off at a diesel repair shop.
Hopefully it is just something with the wiring harness but I have a feeling it's got at least a few bad injectors so I am probably screwed.
View 14 Replies
Driving down the road at 55, the truck just stalled out and won't restart. This has happened before but it always started back up right away. Put a scan tool on it last week and it's giving me an injector 1 low pressure, and egr.
I've read that running the truck at low voltage could fry the FICM and cause all sorts or problems. I just replaced the alternator this week because the batteries always drained while the truck was sitting.
View 2 Replies
My truck started fine my truck was running good. One morning while working from a hotel I went to start it in the morning and it started and stalled more than a few times but eventually ran fine later it did the same thing. The next morning it would not crank at all. I deduced it was the ficm and ordered a replacement the dash was acting funny and tach dropped before it died. I ran the. Test on the dash it swooped the gauges acted fine. I checked and wiggled sensors wires. I also checked were a splice at the crank sensor was it looked good then I bought a meter and the ficm seemed to have the correct volts it was a upgrade. Had 57volts at 1 screw koeo and while cranking.
PCM and replacing the crank and cam sensors. I don't really think it is the harness it will now crank and shut off crank and shut off like it did at first. He said it's stalling because it looses ficm sink. I haven't put new ficm on it ...the harness was allot better than the first. Could the crank sensor splice be wrong it is done its soldered together and heat shrink ... is it the ficm or the dash. I'm out of my comfort level I was also reading it only needs ficm sink to start. Not run. In addition #2 injector is throwing a code. I asked him if he thought the fuel was getting pressurized and his reply was the fuel has nothing to do with ficm sink. Also, I swapped relay out with my other 6.0. And its running fine This is everything I got ....
View 2 Replies
I have 2005 Ford 6.0 turbo diesel. I replaced high pressure oil pump because it would die once it warmed up. Also replaced high pressure fuel rails and icp solenoid. Engine still dies when ect reaches 204 and eot reaches 235. Why it still dies?
View 3 Replies
