Ford 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
Feb 27, 2016
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
View 14 Replies
Advertisement
Had to do the icp sensor originally. went in from the top and discovered my oil cooler was failing too. so i did that. with weather (too tall to fit in the garage) and life getting in the way it's taking me 2 months a little here n there to actually get it done so she's sat for a while. yesterday was moment of truth to get it started again. the batts were old before i started working on it. so i replaced those yesterday.
I've tried and tried to get it to start and it won't turn over. it did for one tenth of a second try. nothing since. I saw that my shifter wasn't exactly in park so i wiggled it and tried to crank it again and now it won't even crank. I have a feeling somehow the transmission isn't reading in park or neutral so it's refusing to crank. I really don't want to tow it.
View 13 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 Replies
Long story short: Got EGR Cooler and Oil cooler installed last week. New headgaskets and bolts. New down pipe. New orings on injectors. HPOP was installed 3 months ago before any of the above work.
Truck drove great for about 100 miles. Then stalled at a stop light. Restarted it. Drove another 10 miles. Truck then dies on me at 25mph. Wouldn't restart immediately. 10 minutes later it started. I drove it back home (couple miles). When i hit the last stop light, the idle immediately changed to crap. Very rough. Got home and parked it and since then I have not been able to start it.
I changed the EGR Valve, tried to start it and it wouldn't. Changed IPR Valve. Put all back together. No start. Cranked beautifully. But doesn't sound like it's taking fuel. note - no buzz/clicking from injectors and no fuel pump noise.
Here are my readings. FICM Sync - 1. I am stumped. I did recommended KOEO, checked emergency fuel switch reset, batteries are at 13.5 avg, checked harness wires and found one connector that wasn't snapped in cause the retaining clips were broken. Getting this connector replaced. Found another wire below chaffed. It is on the intake manifold. what is it for and could this be my problem? Pic below? This is where it connects to intake chaffed. The top of the two wires where they go into the connector were twisted around each other. Maybe wire to wire, maybe not. Would this cause my injectors to not buzz or fuel pump to not come on???
View 14 Replies
After installing a new oil cooler my 6.0 will not crank over and I have no injector noise or communication with my scanner , that is until I unplug the center connector to the PCM then injectors come on and engine cranks and pcm communicates with the scanner....
View 3 Replies
Swapped a new oil cooler and welded Egr shut. Truck ran fine the first 3-4 times I started it except for exhaust leak at the y-pipe/turbo connection. Tried to start it today and it started then ran real rough, blowing whit smoke. Now it will not start at all and blows whit smoke. The only codes I'm getting are egr codes that I've always had due to having the 05 and up intake elbow and the egr turned off via sct. What could be the issue?
View 8 Replies
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 Replies
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
View 14 Replies
Parts came from Riffraft Diesel Performance. A set of "o" rings for the injectors. High flow CVD fittings for the fuel lines. Turbo rebuild kit. (its got 210,000+ miles) Anti Surge compressor wheel.(ok its not part of the oil problem)
Photos to come. I will take during the rebuild.
View 14 Replies
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 Replies
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 Replies
I have a 2005 F250 with 6.0 and almost 175,000. On vacation right now and noticed when I came out of a store that there was a puddle of water under the passengers side. Chalked it up to AC defrost. The second time I was not running AC and puddle again.
Felt and smelt of it...antifreeze. Just put in all new Zerex G05 and a new degas tank because when working on it I noticed a pin hole in the base before we left. I replaced the EGR cooler and hose from Sinister about 3 plus years ago.
Would the EGR cooler hose be leaking? I've noticed that white residue on top of the intake around the where the hose is. What would cause this, Heat, wear and tare....my luck ?
View 2 Replies
I have an 03 6.0 F250. My truck started blowing fuse #45 and it would kill my gauges (fuel, oil, mph, rpm, temp, trans temp, and odometer) and I was just replacing the fuse and putting off the repair.
However, the most recent time my gauges blew, the fuse did not, and I put in a 20 amp fuse, in hopes that it would not blow so quickly, bad idea. So naturally, I ordered a new shift lever, in hopes that it would fix the gauges and I wouldn't have to deal with it anymore, but I think it was too late and something else needs to be replaced. What I could possibly have blown by having a larger fuse in there?
View 9 Replies
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
View 9 Replies
So I went to start my 2006 this morning and it would not crank at all. Like the battery was dead ( all the light in the cab and headlights were working fine. ) so I tried to jump it and still nothing no clicks not crank no nothing. Just for fun I went ahead and jumped the starter (using the same method as when I prime the hpo system) starter cranked no problem so I put the key in the on position and cranked the key again still nothing. So I put the key in the on position again and jumped the starter truck fired right up. So I went back in the cab and tried to start it with the key and it started right up like nothing ever was wrong. What was causing this? Also my voltage was at 11.5 with the key on and engine off when it was running the volts were at 12 to 12.5
View 5 Replies
I bought a 2003 F250 7.3 Powerstroke from a buddy of mine with 99,500 miles. It is a former Michigan truck and has some significant rust issues. Oil pan and drivers door will need to be replaced in the not too distant future. And probably bed rails later too.
In any case, I noticed a puddle of tranny fluid on the driveway when I got home today. The passenger side line at the fitting into the bottom of the radiator has corroded through. The fitting into the radiator is pretty rusty, and the line fitting is darn near destroyed. The line itself actually has a hole in it.
I see the same part numbers on different sites with different descriptions. Driver side here, passenger side there, inlet here, outlet there. For the same number.
As near as I can tell, Dorman number 624-059 is the outlet line from the tranny to the passenger side radiator fitting, and should be the part I need. Correct? Dorman 624-058 seems to be the line from the OTA auxiliary cooler and back to the tranny. What I cant find is the line from driver side radiator to the OTA cooler. That fitting is corroded bad too, and I may as well do both of them.
View 9 Replies
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
View 11 Replies
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 Replies
I have noticed that my truck will crank longer than normal when i park backed into my drive way but it only does it every now and then. I am guessing an internal oil leak but it starts fine cold or hot.
View 10 Replies
Had extreme cold weather here and I left my truck unplugged for a couple of weeks. Started fine but stalled once the fuel was used up in the lines. Replaced fuel filer and filled with that anti gel stuff. Truck sounds like it is almost firing up but still cannot get it to run. When I turn the key on it sound like the fuel pump is working for about one minute and then turns off. Made sure the fuel filter was overfilled with deiseal. Turned it over so many times the lines should be full by now. I used that quick start stuff and it almost starts every time.
View 9 Replies
