I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 RepliesWhile driving my truck to work this morning, it completely died at 65mph. The radio and all electronics are still working. Coasted to a safe place to try and restart, but it won't turn over. The glow plug light stays on. Could this be an alternator problem or something more serious? I'm waiting for a tow truck. I'll see if there are any codes when I get it home.
View 14 RepliesI have a 06 f350 with 140,000mile and today I was driving to a buddy's house and the truck died on me as I was doing 45mph so I towed it home and check the codes I have 1 low icp pressure and 1 low icp during starting / cranking and 1 ckp out of range I think that how it's worded so I looked at the icp pressure and it's 0 and the desired is around 1000 and the volt is .56 and as far as the ckp the rpm are reading so I don't know what to do about that ? Could the STC fitting and dummy plug and standpipe o rings really go out on me like this ? Or am I missing something? I am also trying to track down a oil pressure gauge for the Icp fitting to check it
View 9 RepliesI have a 07 6.0 that won't start it died a few weeks ago while driving. Being a mechanic I've done numerous things to the truck in order to fix all the common 6.0 problems but can't figure this one out. It will crank and get oil pressure and fuel pressure but seems to not be getting fuel. The IPR valve isn't clogged I tried with 2 working valves nothing worked. Along with changing the ficm. The connections to the ficm are clean and all in tact. I have an edge evolution chip that isn't even showing any codes. Not sure what to try next since I don't have any codes to go off of.
View 11 RepliesMy wife was driving through the intersection when the truck died... Tried to start it again but no go, I had it towed home, and stared to troubleshoot.
I have a Scan gauge2 and these were the readings: FMP: 47.5, IPR: 84.71, SYC: 1, ICP: 0
I pulled the IPR (that was only a year old) and the screen was perfect. I had 11.5v at the plug for the IPR, and on the Ohms scale I was reading 1.8Mohms.
I went to the dealer and got a new IPR, and still no start. and the only change in the reading on the scan gauge was the ICP is now reading 56. The gauge on the dash is reading normal oil pressure, but I haven't checked actual Low-end oil pressure.
Last month I replace the HPOP, and 1 faulty injector. Now I thinking wire loom, defective new IPR from the dealership or the new HPOP has failed.
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 RepliesI have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesAnother "no start" issue... The details:
- 2002 F250 7.3L
- Rosewood stage two single shot injectors (rebuilt 1 week ago).
- DP Tuner
- Brand new OEM IPR
- ICP about two months old (OEM)
- New UVH's installed about a month ago
The issue: After installing the injectors and driving about 30 miles the truck died and will not restart. Had to have it towed home. Thus far, I've unplugged the ICP, switched out the CPS with a known good, replaced the IPR, checked the hpop simply by removing the fill plug on the top of the reservoir and gave it a quick crank - oil definitely came pouring out, removed valve covers and plugs to verify oil in the high pressure rails. Oil dummy gauge climbs after about 5 seconds of cranking and seems to hold.
Hoping it's not an injector failure as I just had these reworked. EDIT: Forgot to mention, not seeing any white smoke while cranking. Fuel bowl, full of fuel and fuel pump was replaced this past spring. What to check next? Tried taking a snapshot from a video to show the readings. The ICP seems low, and when unplugged shoots up the 2500, but still no start.
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesMy 2003 F250 started to sputter and died. Won't restart the rest of thw day. Go out next morning will start right up for about 1-2 min and dies like you shut thw key off. Won't restart. Cranks fine.
Oil pressure showing 1300lbs while cranking,ipr is 43% while cranking, but when koeo ipr is 97% which is weird. My excision shows 23% koeo.New oil,oem filters,fuel pressure is at 50 lbs while cranking. Seems electrical or something. Oil pump maybe but why 1300 lbs while cranking of that?
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesI have an 03 6.0 F250. My truck started blowing fuse #45 and it would kill my gauges (fuel, oil, mph, rpm, temp, trans temp, and odometer) and I was just replacing the fuse and putting off the repair.
However, the most recent time my gauges blew, the fuse did not, and I put in a 20 amp fuse, in hopes that it would not blow so quickly, bad idea. So naturally, I ordered a new shift lever, in hopes that it would fix the gauges and I wouldn't have to deal with it anymore, but I think it was too late and something else needs to be replaced. What I could possibly have blown by having a larger fuse in there?
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
So the A/C compressor died on my truck. I am looking at replacing it myself and it looks rather tight in there. My labor manual says I have to pull the fan/fan clutch, fan shroud and right inner fender to gain access.
View 14 Replies2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
So about 3 days ago I made a long 9 hour drive. No problems at all but I did allow my fuel to get a little lower then I normally do. About eighth a tank had 30 miles left on the digital read out. Stopped and filled up at loves where I always get my fuel. And off I went drove it down to 3/4 a tank and made it to my stopping point. Got in to go about 7 miles down the road and come to a stop sign and slowing down the truck died. I thought crap I forgot to turn off the auto start but never done that before. Stopped and stared truck as normal. Made it to my stopping point again. Headed back to the house and doing on average 55mph and truck surges like it wants to die but doesn't.
Rpms drop below 500 and it keeps going I get to same stop sign and slowing down again doing maybe 25ish and truck dies again as I have my foot on the break. Put in nut and started it right up and drive on home. Today went about same distance. Only this time I started it with key and was doing down other things while letting it run it just dies start it back up and take off get to where I was going and it surged or hiccuped so to say. Again started it once I was getting ready to leave and let it run for about 5 min and it died had the heater on as it was chilly out by the lake. Got in and restarted it and it was blowing cold air and had a diesel smell to it. Wife asked me if truck was going to blow up. Backed out of area and put in drive and made it 80' or so and truck died again doing about 10mph
Checked so far
Batteries checked and both are good
No mods done to it
New ICP sensor and pigtail
New water pump
New injectors 20k miles ago
Oil changed 1100 miles ago
New filters upper sad lower
2003 Ford F-250 King Ranch 6.0
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 RepliesMy truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 RepliesHad just got done filling up with diesel, drove 1/4 mile and truck just died. Tried to start it and nothing. No power to edge tuner either. Fuse #22 20a under steering column blown (engine control). Replaced and keeps blowing. not sure what is causing it. Just another wrench to throw in my wedding week!
View 13 RepliesSo I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.