Ford 6.0L Power Stroke Diesel :: 2003 F250 Sluggish Around 35 MPH Till Full Throttle
Jul 13, 2016
2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 Replies
Advertisement
So I started to NM from fort worth texas with my 33" camper blew my CAC pipe four times. Finally got there. In the morning it took longer than expected to start. When it did white smoke. That was replaced with black smoke under full throttle.
I went from elevation of 700 to 8000 Ft. Should I care about black smoke? Meaning should I take it to Ford and get a rental car to get it looked at for our trip home.
96 degrees towing at 70mph with lots of climbing mountains.
View 14 Replies
Driving back from Baseball tonight, I stepped on the throttle truck was sluggish and a huge black trail out the exhaust. On and off the throttle a few times and no more smoke.
Checked codes when we got home and had p132b. I had this a month ago, replaced the map sensor and no issues. So am I looking at a turbo cleaning? Besides the unison ring, is there a seal and bearing kit? I am at 205k at this point and as far as I know the turbo is untouched.
View 7 Replies
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 Replies
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies
The DEF low caution is on and counting down the miles to go but the DEF tank is full. The caution goes away for a start or two then comes back. She's a 2015 F250 with the 6.7L. I love this truck but its starting to really bug me. I don't know if its related but she's been in the shop four times for warranty repairs to the wiring harness in the past couple months. Apparently there were loose connections in a couple of cannon plugs that the've now bypassed which were causing loss of communication between computers...
View 14 Replies
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
View 1 Replies
My truck has been doing great lately after the major surgery she's been through. She is an '06 F-250, with about 238k miles. I've noticed a few days ago that there is a grinding noise and feeling in the gas pedal. (Or diesel pedal..? ) I can feel it right when I slightly ease into the throttle. It goes away once I'm up and going. But its the kind of grinding that sort of worries me. It is also apparent when in reverse, almost more noticeable.
View 3 Replies
I've been having rather slow throttle response with my 6.0 f250 diesel at lower RPMs. Obviously, this is to be expected to some point.. Whether I'm cruising on the highway or through the neighborhood, if the truck is at lower RPMs and I try to accelerate, it doesn't want to. In order to get it to accelerate, I have to press the gas down enough to downshift it then it'll take off.
The truck doesn't have a loss of power at higher RPMs, it takes off like a bat out of hell. I've put 175CC injectors in, tuned it, power max turbo, EGR deleted / studded, etc. It's almost go out with acceleration, or go turtle power with acceleration.
Oil pump was replaced a couple years ago. This problem existed through it all, and it's rather annoying. The truck doesn't want to produce any low end power. If I try to hit the gas enough to accelerate but not enough to force a downshift, I'll just blow smoke, spool the turbo, and barely accelerate until I down shift or push the truck through it. Turbo PSI is roughly ~15ish-20ish during the sluggish transition.
View 14 Replies
2004 F250 Powerstroke Diesel 6.0L ... 90,xxx miles
Symptoms : Within the past 10,000 miles the truck has begun exhibiting the following problems, sometimes in conjunction with one another and sometimes just independently of one another:Stalling on the road at low speed / low engine RPM.
Throttle pedal becomes completely unresponsive. Stabbing the throttle pedal repeatedly sometimes causes it to return to operation. Sometimes the engine must be shut off and re-started to return throttle pedal to operation.
Rough, surging, stumbling idle at rest. Will crank but not fire occasionally. Problem has become worse as of late. Repeated attempts at starting the engine usually result in success after much, much retrying.
Work Done : Local Ford Diesel technician replaced the EBP sensor, replaced the EGR valve and re-flashed computer with latest software -- all under warranty. Problems still persist.
Peculiarities : We have tried driving the truck with the EGR valve disconnected and with it connected, both at the technician's request.
With the EGR valve disconnected the truck usually starts fine but still stalls out at low RPM / low speed. Fuel economy is also cut by nearly 50% with the EGR valve disconnected. Really couldn't afford to keep driving the truck like this.
Technician speculated that if the truck continued to die with the EGR valve unplugged, it meant that the computer or fuel pump might be bad. ????
It also seems that the stalling problem manifests after the truck has been driven at highway speeds (65-70mph) for at least a period of 20-30 minutes. Stalling usually happens as soon as we make an exit off of the highway and begin to slow down to make exit. As in foot off the throttle pedal. Engine RPM drops then stumbles then stalls.
I wonder if this is a problem with the HPOP or ICP system.
Specifically I wonder if this is a cracked quick release fitting that allows oil pressure to fall after the engine heats up and oil viscosity thins out with the heat. Once the engine cools down sufficiently to thicken the oil, the HPOP finally gets enough oil pressure to allow the engine to fire up again.
View 14 Replies
This truck isn't mine but it's an 05 F250 automatic. We just did oil cooler, STC, standpipes, dummy plugs, EGR delete, and cleaned the turbo. Truck starts perfectly and runs great 99% of the time. But after a high load throttle situation right when you let off the throttle the engine sounds and feels like it cuts out for a split second, then it comes back and everything is fine. It does it with stock tunes but it is more noticeable with his SCT tunes loaded. There are no codes being set. The weird thing is if your drive it relatively easily it never does it, and it never does it while it is actually under high load, at WOT it pulls like crazy until you let off a bit and then it happens.. It also doesn't do it every time but it is fairly often. It has edge insight with fuel pressure monitoring added, ICP doesn't drop out and neither does fuel pressure. What could cause it to do that?
View 14 Replies
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
View 8 Replies
I have 2007 6.0, rough idle starts, rough and no power till engine reaches running temperature, runs great after that. If the engine is off for half hour, and restarted, runs rough again till engine temp is back again.
View 3 Replies
Comming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.
Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer
View 14 Replies
My 2002 f250 starts but has no throttle, I did replace the throttle body, still no luck, i did find a wire on the shiffter that had a bad spot , fixxed it still no throttle, code reader says it passes with no codes, I disconnected both batteries and waited 15 to 20 min, reconnected them, started the truck and let it idle for 20 min so what do i need to do now. I just cant figure it out....
View 7 Replies
I just have a 1999 ES300 that is having a strange issue. I realize this is a toyota forum, but the engines should all be the same.
When you accelerate from a stop at full throttle, the car feels very sluggish moving up the RPM range, and acts as though it is missing and stumbling the entire way up. If you do the same acceleration at lets say 70-80% throttle its much faster and much smoother (like the car is supposed to be). Works just fine until the car hits like 55mph, then power just cuts out.
If I'm revving the car in park or neutral its the same story. Works well at part throttle, but full throttle it misses as its revving up. To me this seems like 100% some kind of weird electrical issue. I'm having a tough time tracking it down though.
Things I have done:
1. At one point i had an VVTi OCV code for the rear bank, so I've replaced both OCV filters, and removed tested and replaced the RH OCV valve (they were both working to spec, but the rear one had a little more play in it).
2. No codes by OBDii scanning.
3. Cleaned MAF
4. Checked intake hoses for rips (there are none)
5. TPS seems to be working well based on OBDii diagnostics.
View 14 Replies
03 6.0 with 90k miles. New heads, all orings , stand pipes, injectors , glow plugs, egr delete , oil cooler and studs . Has sct livewire. Just took the truck to the shop for a hard start issue and misfiring at around 30% throttle driving. It would fire up great in the mornings with some white/blue smoke till warm. But after it was warmed up you shut it off it would fire right back up but very slow to reach proper idle.
But if it set for about an hour it would crank great start but same lazy idle up but now it wouldn't get over 300 rpm before it would die. And do this for 5 or so more times before finally idling up. Then runs pretty good other than the misfire. So he said it's either the hpop ipr or icp. I had him replace all 3 with motorcraft parts. Still the same issue ! Return the truck to stock tune and it doesn't have any power . My pockets are only so deep...
View 5 Replies
I have a 03 6.0. I just had all the injectors changed a new fuel pump, spring in the regulator and fuel filters ouch. The truck runs great but I get a puff of black smoke if I get on the throttle going down the road it seem to clear up as soon as the turbo spools up. I that ok or do I need to take it back to the dealer?
View 1 Replies
What is a "normal" number people see on their load factor? Mine was around 25-30 a few weeks ago but I noticed it is increasing to around 30-40 once I'm in gear, in park it's fine. My acceleration is also getting a bit sluggish too especially going up hills and my throttle isn't responding all the way, my turbo boost is normal though and I don't think there is any VGT stiction. I'm thinking either a fuel filter or a MAF sensor to start with. Fuel filters have been in exactly 10 months. Can a dirty fuel filter, air filter, or MAF sensor affect engine load at idle and how fast it accelerates? I feel like I'm pulling a trailer and with it being more sluggish, my transmission is shifting harder as well.
View 14 Replies
When I first start it in the morning and go to take off, It runs sluggish and doesn't smoothen out for the first 1/2 to 1 mile. It then seems to run fine. I have no clue as to what to start checking. The temperature was 65 degrees out, so I don't think that was a factor. I don't know if it's and fuel problem or trans issue, or what. I'm clueless at the moment. It had a recent oil change and fuel filter(s) change. Was doing it before then. 2004 F-250 Super Duty CC 6.0
View 8 Replies
So after I've been driving for a while and stop at a light or drive thru, I will give it throttle and it seems like it wants to stall. Almost like the turbo isn't spooling and then does and all is good again. Is this a sticking turbo bearing or something else? I am not very familiar with this motor(although I have been doing a ton of searching on here) as I just got it about two weeks ago. I should mention that I am getting the 404 and 405 codes so not sure if that could be involved with the egr?
View 9 Replies
