Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Crank / Start - All Gauges Shut Off
Mar 26, 2016
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 Replies
Advertisement
2003 crank no start, 196k bone stock truck egr still in truck and stock head bolts. Replaced the icp sensor and ipr sensor, both from ford. What happened is I got fuel then about 15 minutes afterwards my truck acted like it was going up a hill and was just losing power and shut itself off. ficm tested 48.5 volts all 8 injectors tested good and there is oil pressure. Had an egr fault code but I'm at a loss.....
View 7 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
View 14 Replies
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 Replies
I have a 2007 6.0 crew cab that I'm having some recent issues with. When starting cold in the A.M. the truck will crank, start for a half second then shut down, after about 3 times it will finally catch and keep running. I'll let it warm a bit, then for the first few minutes of driving it will have a pretty noticeable surge on acceleration only, not at idle.
The surge goes away mostly after warm however you can still feel it happening between 22-2700 rpm and can just see the rpm moving back and forth a little. Lastly the fuel mileage has dropped a good amount. If I baby it around town I'll get 10.5 and can see 9ish occasionally.
Truck has brand new ford fuel filters, ford blue spring, fresh oil change, FICM has 3k miles on it, new batteries in last 6 months. Turbo egr oil cooler done in last 20k. Currently has 120k on it.
View 2 Replies
Swapped a new oil cooler and welded Egr shut. Truck ran fine the first 3-4 times I started it except for exhaust leak at the y-pipe/turbo connection. Tried to start it today and it started then ran real rough, blowing whit smoke. Now it will not start at all and blows whit smoke. The only codes I'm getting are egr codes that I've always had due to having the 05 and up intake elbow and the egr turned off via sct. What could be the issue?
View 8 Replies
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
View 4 Replies
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
View 11 Replies
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 Replies
2005 Ford F250 6.0 Diesel (bought new). Never had a problem with the engine until about a month ago. Engine has 220,000 miles on it. Oil and filters changed regularly. Ran low (not out) of fuel, started sputtering badly but not killing. Filled up with diesel. Ran better, managed to get home. The next day it was dead. Crank but no start. Since then I have done the following (not in order):
- Changed EGR
- Changed ICP
- Changed IPR
- Changed the STC fitting
- Changed all seals in the HPOP
- Changed glow plugs and harnesses
- Tested each fuse and relay
- Installed new batteries
- FICM tested 48V
- Changed motor oil and filter
- Changed both fuel filters
- Checked for water in the fuel
- Purged air from fuel line
- Replaced dummy plugs
- No codes
- Prayed the rosary
One month later, still crank no start. Thinking about using it as target practice with the AR-15.
View 14 Replies
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 Replies
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
View 14 Replies
I've developed a problem, usually when starting, that the truck will crank over, start and idle for a few seconds and then shut off. The few seconds it idles it doesn't get any throttle input. I'll crank it back over taking a little more than usual to get it started. When it does start it seems slightly sluggish but that quickly, like almost immediately goes away and the throttle is working again.
Oh, 2001, 7.3 stock w/200k
View 1 Replies
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 Replies
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 Replies
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
View 14 Replies
I have a 2000 f250 7.3 with about 230,000 miles on it. So I filled my truck up to go out of town got on my way drove about 50 miles and the next stop I made the truck shut off and would not start again. I figured CPS went out again! nope changed it still not start. So check the fuel pump seemed fine was getting diesel. Checked oil, was a little low so i topped it off nothing. So i left the truck over night and came back on sunday still nothing. I finally got it started with a shot of quick start i know its not good but i had to get this Truck home. I drove and made it almost home took my foot off the pedal and it stalled again so i pulled it home. Had a guy go over and scan it and it says the oil pressure is at 30 psi when cranking so he says the hpop is probably bad.
View 2 Replies
I have a 99 F 250 7.3. It runs fine at idle even for a long time. When I drive around the block a couple of times it will start chugging and lose power and shut off. I have been mixing fryer oil with the diesel. I changed the fuel filter, oil change, crank sensor and fuel pump. I added 15 gallons of diesel and diesel treatment. Pulled fuel filter and bowel is full I'm not sure where to look next.
View 1 Replies
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?
View 1 Replies
I have an electrical problem on my 2003 f250 7.3 diesel. Sometimes it starts and sometimes it doesn't (mostly doesn't). I have two new batteries in it and have cleaned the grounds at the batteries and at the engine. When I go to start the truck all the lights in the dashboard work and it dings at me but when i crank the key nothing. I wanted to see if i was getting power to the starter and when I put my multi-meter down on the ignition wire on the starter and put my ground lead on the chassis bolt it starts every time.....I'm thinking this should not happen?? Is that a bad ground or a short or something else?
View 14 Replies
