I have a 2006 Ford 150 with about 120,000 miles on it... For almost 9 months now I've had a really rough idle and I can't seem to get it to smooth out. I've tried new plugs, tune up, new fuel filter, higher octane gas, fuel injector cleaner, octane booster, cleaned my mass air flow sensor and nothing works... I've checked the trucks ECM for any codes but it comes up clean every time...
View 6 RepliesI have a 99 lesabre cold start rough idle but smooths out . Warm no start. Trouble codes P0171, P0300, P0336. Had plennum replaced 2 years ago but I'm seeing coolant around the base of the plennum so I'm going to have to do that again but I don't think that has anything to do with the warm no start.
View 14 Replies1994 Buick LeSabre Custom 3.8 Litre V6 with 103277 miles.
It runs smooth when idling in Park, rough when I put it in gear when I am stopped (either drive or reverse) has hesitation when accelerating, it smooths out again when driving then it starts to drive rough at about 55 MPH.
Mechanic told me it was the plug wires. I replaced those and the plugs. This fixed the hesitation when accelerating issue, but the other issues remain (now even seem a little worse) I thought the plugs and/or wires were bad, so I rechecked the gauge on the plugs and traced to make sure I had the wires hooked up right. Everything seems in order.
I have added fuel injector cleaner, and changed the oil, oil filter, spark plugs, spark plug wires, air filter, flushed the radiator, and changed the thermostat. (For a tune up since it has admittedly been a while)....
I recently purchased a 2006 SE with 4 cylinder/at combo. Engine is silky smooth, but I have a rattle that I think is coming from behind the driver instruments or against the fire wall where the brake m/c is. This only occurs when the engine is in gear, mainly with a/c on, & the idle drops to 600-700 rpm range. Like if I am sitting at a red light for more than a minute or two. If I put the tranny in neutral, cut the a/c off, or step on gas to raise the idle speed the rattle goes away. It's definitely rpm dependent.
It's not the a/c, because I have been able to repeat the issue with the a/c off. I did notice that on the back of the air filter box, there are several plastic components attached but what they do. Is there anyway to increase idle speed?
My 2004 Lincoln navigator is very rough at idle but runs smooth when I give it gas. Someone said my VCT may be stuck or bad. I looked at Youtube videos of VCT replacement but in all the videos the VCT's are up front in the valve covers. On the Navigator they aren't there. Where the heck they might be located?
View 2 RepliesMy truck has been running great for the lasts 2 years. Today is actually the 2 year anniversary of me buying the truck. Still have great power and rumbles great down the road with no lights or anything.
Lately though at stop lights my idle will be inconstant. Will either sit smooth at about 550rpm, or be high but smooth around 700, OR that one that worries me the most is it will idle at 550rpm then drop down to 450 or so then catch itself and go back to 550, then drop back down.
It has the usual maintenance, new spark plugs around 100k, oil change and air filter just a few weeks ago, so this idle has me a bit puzzled. Maybe time for a new fuel filter? MAF sensor dirty?
Recently bought a 96 4 cylinder 5speed 2wd ranger. 200xxx miles on it and its former owner had a young guy change spark plugs . Truck ran fine before, but after is when the rough running showed up.
A quick check of the plug wires and there locations looked correct and also tested the wires for spark with a timing light attached to them, checked shows all are firing.
Seems to smooth out a bit when rpm's are raised up, but still acts like not running smooth.
I swapped out plugs. Looks like they haven't been changed in a long time .Some of the straps are burnt and are shorter than they should be, but still runs rough, very little improvement .
Check vacuum lines for leaks/breaks and all looked good. removed line off brake booster and plugged, didn't matter.
It doesn't throw and check engine lights. It does smooth out some as the rpm's rise, but still not smooth .
basically it runs rough and makes noise when AC is on. While it may not be perfect when off, it certainly is quieter. Check engine light just came on.
View 5 RepliesI have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.
I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?
I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.
I have a 2011 Santa Fe - I have noticed it is quite a rough ride. I guess I am used to the suspension in my Passat, but I still find it is not as smooth as it should be. I thought maybe giving it a bit of time would work, but so far at 25,000km it is still the same. Find it's a bit of a rough ride? Or should I look into it?
View 39 RepliesI just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 Replies2003 F350 6.0 with 290k+ ... It has a skip in the engine at idle and running. At times when running down the road skip seems to get worse. Changed both fuel filters, didn't work. Truck start up is normal, no leaks, and flashing no codes.
View 3 RepliesI have a Ford F150 XLT. I have 67000 miles on it and the other night it just started running rough out of no where near idle. Once you got over 20mph the rough running would go away. I took it to get an engine change and engine flushed but it came back. It doesnt always run rough near idle or below 20mph. The Ford dealer says my engine has only 22 psi oil pressure near hot idle and cant engage the VCT phazers and they want to replace the whole engine.
View 1 RepliesI just bought an 2006 f150 4x4 with a 5.4l 3valve, and this morning when I pulled into work it was idling Rough as I let off the gas and rolled into my parking spot. No check engine light or nothing, just when it's in gear Rpm is at 600-700 and vibrating. When I shifted it into neutral or park it went away and the engine ran smooth. According to the oil pressure gauge I've got good flow. I was told from the dealer that they replaced the cam phasers, timing chain and put new spark plugs in it. What the issue is here?
View 1 RepliesOk new issue that started yesterday only get it at idle. Runs great above idle no real power loss or change in fuel econ. Haven't really had a chance to test much. I was thinking maybe a injector issue but I don't know
View 14 RepliesHaving problem with 2016 Accent Sport (or other model) idling rough after smooth driving for about 20 or so minutes? It has started doing this about a month after being purchased. About 700 miles or so on it) When in stick mode it smooths out and purrs like a kitten, but back in automatic mode it idles rough, with Active Eco on and off. I have an appointment to take it in to the dealership 5/7, but I wanted to see what the cause was.
View 7 Repliescompletely stock 2006 4.6, 230,000 miles, I purchased and can vouch for everything after 106,000.
Two separate issues...have had a slight ticking noise growing for about the last two years. Seems to get slightly worse near an oil change but that could be my imagination. It has finally gotten loud enough that my wife (who drives with the delicacy and observational skills of a Sherman tank driver) actually mentioned it to me the other day. It is directly related to engine speed whether the truck is in gear or not. I kind of think it might be a manifold gasket going out but am not sure. Am not very worried about it but...felt like I needed to mention it because of my bigger problem....
Truck has gotten very "cranky" on startup in the last week. Has a rough time finding an idle speed but typically sorts itself out after about 5-10 seconds. This afternoon it started idling rough at a stoplight. It got steadily worse and noticeable even at speed. Four stoplights and nine miles later it threw a code and coincidentally, I was in front of an Advance Auto. They read it and said the #3 cylinder was not firing. I bought an ignition coil, drove 15 miles home and changed it. From everywhere I looked online, this is the second cylinder from the firewall on the passenger side.
Had a little trouble getting it in and am not entirely sure it is fully seated in the slot, but I can't get it to go any further. Seems as tight as a couple of the others. I disconnected the battery to clear the codes, cranked it up and it seems to run "better", but still has a rough idle. Just test drove it about 12 miles and no check engine light but the idle has not cleared up. I think coil must be working fine because I have no issues at highway speed. Earlier, when I backed off the gas you would feel the miss very badly, but not as much when under a load.
I just bought a used 2006 Ford F-150 it has the Triton 4.6L V8. Seems to be running ok a little white smoke on start up, but the other night after leaving work at 5am when it was around 10 degrease freezing. When I started my truck it was idling very rough like it was about to die but it didn't after it warmed up it was a little better but I think I seen black smoke from the rear end, but like I said after it was warm it sounded like normal so I started to head home and got about 15 mins down the road and it started to run very bad like it was bogging down and lost all power if I pushed on the gas all the way I was not picking up any speed but if I let off the gas the truck would jerk very bad and gain speed. But the next day in the morning it started up fine no problem I even drove it around town with no issue. What this issue could be?
View 1 RepliesI'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
I recently bought a 2006 that idles rough, not real bad, but bad enough for me (and my 9 year old kid!) to notice. I asked the dealer where I bought it and they put it on the computer and said everything checked out. He said "it's a characteristic of this motor." I've never heard of such a thing. The truck has 27,000 miles on it and the dealer flushed the fuel system. He said the throttle plate had a lot of carbon on it, but it still idles rough... 4.6 idle rough?
View 13 RepliesI have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 Replies