It has a floor shifter for the xfer case with 2wd, 4wd-H,and 4wd-L, and Neutral positions. It works fine in the 2wd and the 4wd-H positions. The problem is it sometimes slips out of 4wd-L position into 4wd-Neutral, which I have just lived with, but it is annoying. I think I heard this is a known problem with these 1970's Ford xfer cases, and the fix involves removing the xfer case and replacing a part.
View 10 RepliesEarly 70's Ford Truck w/Dana 20 Xfer case
The problem is that when I put the truck in 4W Low, it will sometimes slip out of gear into 4W Neutral. It happens more often when climbing hills than driving on level ground. It hasn't ever slipped out of 4W High. It is drivable the way it is, but it's annoying. If there were an easy fix I'd do it. If I have to remove the xfer case, that seems like a big job, so probably not. What do you think?
The manual suggests these four as possible reasons
Shifting poppet spring weak.
Bearing broken or worn.
Shifting fork bent.
Improper control rod adjustment.
Which is the most likely problem? What is the "poppet" for and where is it located? Can anything be done to diagnose or fix this problem w/out removing the xfer case from the vehicle? What about the control rod? Can it be adjusted with the xfer case installed? If so, where is that adjusted?
Looking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 RepliesI just replaced the transfer case BW 4405. And I noticed that the 2 sensors (front drive shaft and rear drive shaft) are bad. What is the name of these two sensors? I'm looking for a brand new ones...
View 13 RepliesWhere/how to check the ATF in the transfer case? I found the lower drain bolt,but I don't see anything up higher that looks like a fill hole.
'91 Aerostar 4.0L AWD
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 RepliesSwapped out my transfer case since mine was detonated and now my tranny is running hotter? Drove in town for about 10-15 minutes and noticed my temps climbing and once it got to 180 it felt like it was slipping when moving from a full stop. i went home and parked it. Checked my fluid level and it looked a little low so topped it off while running and went through gears to make sure it was good. Drove again and it still went up to 180 in 10-15 minutes in town driving. Before we swapped the transfer case it was driving fine and went on a road trip 6 hour drive and felt fine. I bought the excursion and it supposedly had a new tranny in it.
View 14 RepliesSo long story short I have a 92 Aerostar AWD which I'm pretty sure had the transfer case recall done (97V204000 1992 FORD AEROSTAR Recalls) it has the aluminum driveshaft but a couple of years ago the transfer case cracked and I replaced it with a "New OEM" transfer case off eBay. Fast forward to the present and my van has a strong vibration at 60+ my transmission guy says it all looks good so the vibration has to be from one of the driveshafts. My thought is that I may have got a transfer case without the recall done on it and its warped my driveshaft. I don't really know thats possible or what I could do about it if that was the case.
View 8 RepliesI bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 RepliesAbout 9 months ago heard a strange noise when shifted into 4 wd , sounded like driving over those grooves on the side of the highway to keep people awake.
Had to pull over to stop , as it would not go back into 2wd with the noise still going.
Then it stopped , after shutting truck off and restarting.
Then earlier this year after trying to do it again in 4wd had bad clunking noise and was hard to get back in 2wd , I can here the shift motor engaging and the dash reads in 4wd, seems its not engaging fully in 4wd and not going back to 2wd, its a very bad clunking noise, shakes the whole truck.
The dang thing leaks from the fill plug, I been reading about using liquid teflon on it.
View 4 RepliesI had sold my Explorers but just picked up a 2000 Excursion V10 plow truck. It has been hacked and slashed I find cut wires under the dash and hood. I have tried everything to get the 4x4 to engage and no luck. It is used just for my driveway no road driving...
So question is: Can I engage the 4x4 at the transfer case so it will go, and stay in 4 wheel drive. If so do I take the shift motor off or does that big bolt by the motor do anything.
I keep getting a check engine wrench on the readout, put a scanner on it and got the following code:
P183b transfer case code ...
What this means?
My 4WD sport trac was running fine. I took it off road and put it in 4WD. After I was done in the woods. I put it back into 2WD and backed up to unlock. I then drove 2 hours home. The next day the transmission started shifting funny, especially overdrive almost like I was low on fluid. (which I check and I'm not) And the truck sounds like its running ruff. Is my transfer case still ingaged? Do I need to take it in for tranny work?
View 9 Replies I have a BW 1345 transfer case. Does it have the shift in the fly capability? And, if so, what precautions should be taken if shifting on the fly?
Second, where can I get a "plate" or label that shows the shift pattern? I know the shift pattern, I just want to post it in my vehicle in case anyone else ever drives it and needs to use the 4 wheel drive.
I have a 99 f150 with a 4.2 manual with four wheel drive I need to replace the speed sensor in the transfer case it looks a lot like the one in the rear end I've called the auto parts stores and they show nothing. What sensor I can use ? I did find one on rock auto that said it was for the transfer case but after looking into there part I found it was for a automatic ...
View 1 RepliesMy 97 4.6 ran fine but the 4x4 light came on even when the transfer case lever was in 2wd. Then one day it would not start. It cranked over fine but would not fire. I added fuel but it didn't work. I pulled a spark plug lead and attached a spark plug while I jumped the solenoid and cranked over the engine to visually check for a spark as I have done on older trucks. Well it cranked a couple of times and then it died and won't even crank now, I must've fried something, the batterys fine. If there is a fuse or something? What could have happened when I jumped the solenoid?
View 4 RepliesI found that my transmission was low on oil but couldn't find a leak. What I did find is that the seal in the transfer case was letting trans fluid transfer into it and then it would leak out the out put seal. I purchased the new seal and gasket and repaired it myself in about 3 hours. I removed the rear drive shaft and removed the front drive shaft from the transfer case alone or you can take it out completely if you want.
Drained transfer case unplugged wiring and one vacuum line. Unbloted from trans and removed using trans jack. The bolts are not the easiest to get to. i used a 3/8 ratchet to break them loose then used a stubby 3/8 to get them out because they are around 2 inches long. Once down I had to jack up the truck to get it out from under it. I removed the old seal and installed new one cleaned everything up and installed with a new gasket.
Having problems. Transfer case broke in half, I think it is because of the auto free wheeling hubs. Is it possible to manual hubs on it?
View 11 RepliesMy TC motor picked today of course with the snow to go bad. Luckily I hobbled to advance right as they were about to close and got one. I laid in the snow and changed it. Needless to say I got soaked beyond belief. Anyways now it changes in and out well but still seems way to loose in the rear. Not sure if something else is malfunctioning or if these things are like that. Right now I don't feel nearly as safe as I did in my expedition and that was without even using 4hi or low just the A4WD. The excursion is sliding everywhere. My tires have great tread but are highway tires so maybe that's the issue. They are Dura Grapplers. I'm going to try throwing some weight in the rear to maybe gain some traction.
View 2 RepliesOn my 2007 f150 5.4 last week i changed out the driveshaft and it smoothed things out. This past weekend I dropped the transfer case oil and refilled it with motorcraft transfer case oil as per ford but now the front end seems to shake more than before. It just seems to come through the steering wheel but the wheel seems tight almost like a death wobble with solid front axles except obviously this truck doesn't have that. There are no leaks and I filled it up to the top fill hole with between 1.5 to 2 liters of oil until it started running out. I should also mention that when i went to check the level it was overfull on the top plug but it was that way for the last 90,000 km or so.
View 3 Replies