F Series :: 1985 Ford Would Not Start And All Dash Lights Went Out
Apr 25, 2014
My 1985 Ford F-150 6 cyl. manual with overdrive would not start when I turned on the key, moved moved the key to start... It suddenly did nothing and all the dash light went out. I assumed the battery was run down and then tried to start it with my 2010 Ford car.
It still would not start and all dash lights went out. I then put my battery charger on the battery and charged fully charged the battery. I then turned the key off and back on and the dash light went on, tried to start again and the same thing happened. After about 10/15 minutes, I tried again and still did not start. I waited another few minutes, turned the key on and jumped from the battery positive to the starter cable after the starter solenoid and the engine started.
I ran it for a few minutes, and the backed it into the garage. The next day I again tried to start it and again, there was no power to the vehicle... no headlights, brake lights, dash light...nothing. I assumed the starter solenoid was burned out and replaced it. Still did the same thing. I replaced the fusible link on a yellow wire attached to the battery side of the starter solenoid. Still no power.
View 2 Replies
Advertisement
85 ford ranger 2.3 efi .. My brake lights still aren't coming on. According to the Haynes manual, the wire that runs from the stop light fuse goes from there to the hazard flasher and then to the brake light switch. Since I have checked everything else, is it possible that the hazards are causing a break in the connection?
View 4 Replies
So I did alot of electrical work on this truck but never had any problems with the brake lights, now they dont work and the fuse blows every time you pop one in.
View 1 Replies
I was driving my 85 2.3 liter down the road and it died all of a sudden like and wont start back up. I took out a plug to check for spark and had someone turn it over and I touched it to the big metal part the grill connects to at the top but I got nothing. It IS getting gas. The spark plug was white as if it was really hot and rough-looking for its relative newness. I bought a new distributor cap because it was corroded, but it didnt work. They tested the ignition module at the store and its good, so I am thinking distributor?? Also, could compression issues keep it from sparking? I am a little worried it got over-heated somehow, but don't know....
View 9 Replies
I have a 1985 Cutlass Ciera Brougham with a 2.5L four. Got in it one day and when I turned the key nothing happened except the dash lights came on. No clicking or buzzing, no engine turning over, nothing... Pulled the starter and had it tested, it passed. Then again it is only about a year old. I then jumped the poles on the starter and the engine came to life. Replaced the ignition switch ( the electrical part ) still have the same problem. Turn the key and nothing happens except the dash lights.
View 8 Replies
I have a 2004 Saturn SL2. My Engine Turns over ok, but won't start. When I turn on my ignition key, the Dash lights Start Blinking.
View 3 Replies
My '96 ranger with a 4.0 auto will be running fine and then dies. When you go to start, the engine will will crank over. Also notice that there are no lights coming on the dash when the key is in the run position. A few hours latter the truck started right up. Not reading any codes. Transmission was rebuilt a few weeks before this problem.
View 6 Replies
I have a 1999 Ranger 4x4. My 4wd does not engage when I turn the switch to 4wd lo or 4wd hi. The lights on the dash flash on and off. I disconnected the battery and now the lights are clear. But if I try again to engage it, the lights return. I feel I have a vacuum issue but would like to know more about locking hubs. If I convert them over, how do I know that my system will work? There has to be something else that changes from 4wd lo to 4wd hi. How do I check to see if this is working properly.
View 6 Replies
I have a 97 ford ranger V6 4.0. my 4x4 lights flash on my dash board 6 times and go out, a few minutes later it does it again. When I lock my hubs and put it in 4x4 nothing happens. What could be causing this?
View 5 Replies
I have a 85 Ranger with a 2.3L engine. I'm not getting any heat. The temperature gauge never moves off of C, except when stuck in stop & go traffic. Even then it doesn't come up much. I tried to fix this last year by putting in a new thermostat, but it didn't work.
View 6 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 Replies
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 Replies
My ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 Replies
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 Replies
So 85 ranger with 2.3l and A4ld. I can manually shift to get first and 2nd. When i look at the vaccume diagram it shows these 2 blocks on the tranny,one box is connected to the next with a vac line. The other box has 2 lines, one goes to the main vaccume block on the intake and the other T's into a small capped off canister and the egr. I can only find one place for a vac line and its on the pasgr side of the tranny... Where is the block that the egr line connects too located? Its not on the tranny as far as i can tell.
View 2 Replies
When I turn on my heater full blast the most god awful squealing commences. Where to start spraying the grease?
View 10 Replies
So I noticed when I check the oil, there is a very small amount of water at the end of the dipstick and also water mixing with oil around the oil cap. It is not much water at all, but my first thought was head gasket. I was loosing very small amounts of coolant, but found a small leak at the thermostat housing....The truck runs fine, idles fine, no bubbles coming from the radiator at startup, no moisture from exhaust. It seems to be using more oil than normal, but I drive it 100 miles a day still and no major issues other than the perplexing bit of water and oil mixing. Could it be a tiny head gasket leak? What else would cause the water and oil to come together.
View 13 Replies
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
View 14 Replies
1985 2.3L... New fuel pump And fuel pump relay, problem was happening before new parts. the wires at inertia switch continue to get hot switch has been removed. The heat continues to under the hood where there is some so rt of connecting link and heat stops.what the is this link for, it doesn't look like A fusible link?? Saw a similar post here about a fuel pump shutting down and wires getting hot. Same problem.
View 9 Replies
Our 2011 Fiesta wouldn't start, key in the ignition and all the interior lights would come up on dash and interior. Friend of mine said, "sounds like a relay", came over and he swapped the low beam relay to the starter relay (said they where the same), car started just fine.
We put the bad relay in the glovebox, and planned to run to the auto store today. Except today it won't start in the exact same way it wouldn't start yesterday. Do i have 2 bad relay's in 2 days? Or as i suspect is this is a sign of a bigger issue?
View 8 Replies
