Explorer :: 2001 Ford Idles Very Low In Drive And Reverse Then Shuts Off
May 1, 2013
I have 2001 ford explorer sport.. it idles very low in drive and reverse and then shuts off.. What has been replaced:
1. Torque converter
2. All new plugs n wires
3. Map or mass sensor
4. Iac valve
5. O2 sensors
6. Fuel filter
7. Air filter
8. Throttle valve/sensor
It does not run bad only when u come to a red or stop light.. Had the vacuum tested and no vacuum leaks.. also no check engine light has come on and no codes have popped up when tested..
View 1 Replies
Advertisement
I just got myself a 1993 ford explorer and the damn thing won't drive forward but it will drive in reverse. What could be the problem?? I've already drained the Transmission Fluid out & refilled it. My friend told me it is most likely the Neutral Safety Switch but I have no clue where it is located. I will be honest I have absolutely no clue about vehicles.
View 1 Replies
I got my first truck about a months ago 2001 ford f150 v8 5.4.. has 155,000 seems to run good.. but about 3 days ago i started to notice that when I am in my driveway ill start it let it idle for say a min or so... then when I go to put it in reverse it will idle up for a lil bit.. it didn't do that till about 3-4 days ago.. other them that everything is fine.. should i get the transmission fluid flushed??
View 7 Replies
My car is taking a long time shifting from reverse to drive in the morning. Do you know what may be causing it and how to fix it. It's a 1995 automatic ford explorer.
View 3 Replies
I got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 Replies
I have a 2004 Ford Explorer V8 4 wheel drive. Yesterday I was on the way home from a 2 hour drive and was on the expressway at a complete stop on a downhill grade. When I hit the gas, the car started lurching - it would shoot forward, then slow down, then shoot forward, then slow down.
I got the car to the side of the road and called a tow truck. Just to test - while I was waiting for the truck I put the car in neutral and even though I was on a steep downhill grade, it wouldn't roll at all. When I put it in drive - it wouldn't go initially until I had to put a decent amount of pressure on the gas pedal. I reminded me a being at a speed bump that you couldn't idle over and have to give the car some gas to power it up over the bump.
When the tow truck got there - I watched the driver drive the Explorer up onto the bed of the tow truck. What I noticed was this:
The left front tire was completely locked when he was hitting the gas. But when he gave it enough gas, the right tire that was working would push the car forward while the left tire remained locked creating friction on the pavement but the car was still moving forward from the other wheel.
Then after 3 or 4 feet - the left tire would unlock/release and start to rotate - causing the car to suddenly lurch forward. But then after another few few it would lock again. Then release again.
The thing I found odd was that when the driver later reversed the car down off the truck - the left front wheel worked just fine. So the car works perfectly in reverse, but in drive the left wheel locks then releases then locks then releases.
View 12 Replies
I've read a lot on hear but can't seem to find what I need. I just replaced one of the battery cells. Now when I drive for about 20 min the engine idles high and the energy read out stops charging the hybrid battery. The AC recirculation turns off on its own. I have a few codes. the O2 sensor and cat code. The p3006. I had one cell that i didn't replace that was reading 6.9 volts. I thought that it would charge back up on its own. We went of vacation for 2 weeks and the car didn't get driven. I found out that's not good for an older prius.
View 5 Replies
I gave my daughter the '01 sport trac as her first car... just had to do: fan and clutch, ps pump, ac compressor pulleys, a/c line, actuator...
Now the reverse lights have gone out. Bulbs and sockets appear just fine... did notice shift indicator on dash is off just a bit... it reverses just fine....
Is there a linkage adjustment or some switch that is bad?
View 4 Replies
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
View 3 Replies
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 Replies
Was going to leave the other morning and put it into reverse and nothing happened. Tried every other gear and works fine. Reverse is the only thing giving me problems right now. Tried doing some research on my own, because I can't afford a tranny rebuild. I was hoping it was either the solenoid or low/reverse band. I don't know about the band, because it works fine in low2 and low1....
View 2 Replies
My 06 was parked about 2 months and when I first started the truck, the CEL light came on. It idles a couple of minutes and shuts off. It was running very well before it was parked. I put a code reader and the codes are P0607 and P2107.
View 1 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
My 2003 Santa Fe makes a grumbling noise when first started, and put into drive or reverse. The noise seems to be coming from the passenger side of the engine compartment. The noise disappears when the drive train has warmed up.
View 4 Replies
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 Replies
I have the following codes:
P0705
P1529
It looks like P1529 is caused by P0705. P0705 is the neutral range sensor. I purchased the sensor and replaced it. It is aligned correctly and I am still having the same CEL and codes.
What the car doing: The car jerks into reverse and drive. The dash does not indicate what gear I am in (PRNDL).
When it drives, acceleration is very slow. I believe the car is "stuck" in third gear. I've heard of fail safe mode?
What I did: This problem started when I changed my stereo. I did three bad things which may have caused this problem.
One, I had to put the car in "L" to get the dash off. I left it in "L" for a while then I tried starting the engine while it was still in "L".
Two, when I reinstalled the center console I swapped the wiring for the hazard lights and the rear windshield wiper (GT)
Three, I wired the dash illumination positive and negative together.
The cluster's backlight does not come on anymore and these codes came up. I checked all fuses and they are good. Where to look for a possible shorted wire that can be causing this?
View 10 Replies
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
View 2 Replies
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 Replies
So I have a 06 350 and I'm getting clunking from drive to reverse and now with drive too, I know my rear diff is on it's last days but I am wondering if that could cause the clunking and now my truck around 90km shakes likes crazy and same thing wana know if that's the diff. And if I was to fix diff myself would it not just be easier for me to just swap axles if I wanted to be cheap??
View 12 Replies
I have a 2002 santa fe 2.7. I just had the transmission rebuilt and since then have noticed a clunking sound when I shift into drive or reverse. It seems to be the lower motor mount is making noise from the motor moving the mount. I look at the mount and it appears to look good, but was wondering how I can really tell if a motor mount needs replacing or not.
View 3 Replies
I recently bought my '05 Elantra from a small dealership and I'm starting to see a problem with it. If I shift into reverse and then go back into drive, the car doesn't go forward at all. I have to mess with the gear shift a bit to get the car moving. I'm pretty sure it's a bad linkage. The dealership I bought it from said it desperately needed motor mounts when they got it so they replaced 2 of them. I'm sure the problems are related. I can't find any information on replacing it myself though.
View 1 Replies
